Installation Instructions

ManualsBrandsToro ManualsAttachmentsChemical Pre-Mix Kit, 2015 and After Multi-Pro 5800 Turf Sprayer

FormNo.3395-538RevA

ChemicalPre-MixKit

2015andAfterMulti-Pro5800TurfSprayer

ModelNo.41622—SerialNo.315000001andUp

InstallationInstructions

Thiskitisdesignedtoaidinthemixingofchemicalsin

preparationforturfsprayapplicationsonwell-maintained

lawnsinparks,golfcourses,sportselds,andoncommercial

grounds.Itisadedicatedattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww.Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3395-538*A

Summary of content (20 pages)

PAGE 1
Form No. 3395-538 Rev A Chemical Pre-Mix Kit 2015 and After Multi-Pro 5800 Turf Sprayer Model No. 41622—Serial No. 315000001 and Up Installation Instructions This kit is designed to aid in the mixing of chemicals in preparation for turf spray applications on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils, or other property. • Carefully read and follow the chemical warning labels and Material Safety Data Sheets (MSDS) for all chemicals used, and protect yourself according to the chemical manufacturer's recommendations.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Qty.
PAGE 4
Procedure 5 6 Description Use Qty. Bulkhead O-ring Locking ring Retaining fork Forward hose assembly Gasket Worm-screw clamp R-clamp Carriage bolt (5/16 x 1 inch) Lock nut (5/16 inch) Supply hose Gasket Worm-screw clamp Hose clamp Hose adapter Retainer pin 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 Install the forward hose. Install the supply hose. Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 5
Figure 5 Figure 4 1. Nuts (existing) 5. Eductor valve bracket 2. Eductor valve bracket 6. Eductor valve assembly 3. Bolts (existing) 7. Retainer pin 4. Flange nuts (1/4 inch) 8. Fitting (1 inch) 1. Bypass hose 3. Pump tee 2. Relief hose 4. Supply hose 7. Remove the horizontal hose tee from the side of the pump tee and attach it to the top of the pump tee (Figure 5). 8. Connect the supply hose to the side of the pump tee and the bottom of the eductor valve (Figure 5). 4.
PAGE 6
4. Install a lock nut over the lower exposed bolt passing through the frame to secure it to the tank strap (Figure 7). 2 Assembling the Frame 1 2 Parts needed for this procedure: 1 Support frame assembly 1 Locknut (3/8 inch) 1 Back plate assembly 1 Cradle arm, right 1 Cradle arm, left 2 Bushing 2 Pivot pin 2 Jam nut (3/8 inch) 2 Handle Bolt (3/8 x 1-1/4 inches) 1. Main support frame assembly 3. Exposed bolt, side 2 2 Set screw 2. Exposed bolt, top 4.
PAGE 7
Figure 9 1. Cradle arm, left 2. Pivot housing Figure 8 1. Back plate assembly 7. Handle 2. Hair pin 8. Bolt (3/8 x 1–1/4 inches) 3. Flat washer 4. Bushing 9. Right cradle arm 10. Main support frame assembly 5. Pivot pin 11. Cradle arm axle 6. Jam nut (3/8 inch) 12. Pivot housing A. Start by installing the right cradle arm to the frame. The right cradle arm is denoted by have the long axle. B. Insert the axle through the hinge shaft. C.
PAGE 8
plate assembly of the cradle to compress the spring tabs midway (Figure 11). 3 Installing the Latching Components Parts needed for this procedure: 2 Spring Installing the Springs 1. Install the spring in the hole in the lower end of the angled tab on the side of the frame assembly (Figure 10). Figure 11 1. Spring tab under pressure 3. Spring tab 2. Back plate 1 2 5.
PAGE 9
4 Installing the Eductor Parts needed for this procedure: 1 Eductor 1 Handle 2 Flange-head bolt 1 Spring clamp 2 Bolt (#10-24 x 1/2 inch) 2 Locknut (#10-24) 4 Bolt (3/8 x 1 inch) 4 Locknut (3/8 inch) 2 Flange-head nut 3 Hex-head bolt 1 Latch post 1 Latch handle 1 T-valve 1 Gasket 1 Worm-screw clamp Figure 13 1. Handle 6. Flange-head bolt 2. Eductor 7. Locknut (#10-24) 3. Flange-head nut 8. Latch post 4. Spring clamp 5. Bolt (#10-24 x 1/2 inch) 9. Extension bracket 10.
PAGE 10
. Tighten the fasteners securing the eductor to the cradle. Note: Torque the fasteners to 36-45 N-m (27-33 ft-lb). 11. Tighten the 2 set screws on the left pivot arm. 12. Check the overall position of the eductor assembly on the tank strap. Note: The eductor should be upright, in the transport position. Loosen the lower locknut on the frame assembly securing it to the tank. Do not remove the locknut. Adjust the position as necessary and tighten the locknut. Make sure that the strap is secure to the tank.
PAGE 11
Installing the Bulkhead 5 1. Open the main tank lid and remove the filter screen. 2. Install the bulkhead and the O-ring up from inside the tank through the previously cut opening (Figure 18). Installing the Forward Hose 1 Parts needed for this procedure: 1 Bulkhead 1 O-ring 1 Locking ring 2 Retaining fork 1 Forward hose assembly 1 Gasket 1 Worm-screw clamp 1 R-clamp 2 3 4 1 Carriage bolt (5/16 x 1 inch) 1 Lock nut (5/16 inch) G014022 Figure 18 Drilling the Tank 1.
PAGE 12
4. Install a lock nut over the bolt in the R-clamp and finger tighten at this time (Figure 19). 6 Note: This will allow for later adjustment. 5. Attach the other end of the hose to the forward-facing opening of the eductor using a gasket and worm-screw clamp (Figure 20). Installing the Supply Hose Parts needed for this procedure: 1 Supply hose 1 Gasket 1 Worm-screw clamp 1 Hose clamp 1 Hose adapter 1 Retainer pin Procedure 1.
PAGE 13
Figure 23 1. Supply hose 3. Retainer pin 2. Eductor valve assembly 5. Install the open end of the hose into the eductor valve and secure the hose using a retainer pin (Figure 23). 6. Slide the hose clamp over the fitting barb, and tighten the clamp to secure the fitting to the hose. 7 Finishing the Installation Parts needed for this procedure: 1 Suction lance and hose (optional) Procedure Note: The suction lance and hose are optional accessories.
PAGE 14
Handles and Transport Strap Operation Use the upper and lower handles to raise and lower the eductor and to lock it into the Transport position. CAUTION Chemicals are hazardous and can cause personal injury. Main Valve Use the main valve to introduce chemicals from the eductor into the hose leading to the main tank. • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions.
PAGE 15
Raising the Eductor Starting the Eductor 1. Lift the lower handle to raise the eductor while slightly tipping it toward the tank. Note: Close the eductor hopper valve and hopper rinse ball valve(s) before starting the eductor. 2. Guide the tongue under the crossbar with the welded tab in the upper portion of the frame assembly. 1. Lower the eductor. 2. Open the lid to check for foreign objects which may hinder performance or contaminate the system. 3.
PAGE 16
Figure 26 1. Suction lance 2. Eductor 2. Use the free end of the lance to pierce the bag or container to vacuum powdered or liquid chemical. 3. Place the lance end into a clean container of water to rinse the lance assembly. 4. Remove the lance body from eductor and drain any remaining fluid into the hopper. 5. Close the hopper valve (red handle). Shutting down the Eductor 1. Close all the valves. Note: Close the hopper valve first. 2. Remove all chemical residue. 3.
PAGE 17
Troubleshooting Problem The eduction rate is low. Possible Cause 1. There is a lack of flow and pressure to the eductor system. 1. Increase the pump speed. Turn the agitation throttling toward the closed position. 2. The outlet/Inlet hose is obstructed. 2. Disassemble and remove any obstructions. 3. Use only sweeping turns with flexible hoses. 3. Fittings with elbows or other flow-restrictions are in the eductor outlet. There is no rinsing or flushing action. There are leaks at the fittings.
PAGE 18
Notes: 18
PAGE 19
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
PAGE 20
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).