Quick Start Guide

ManualsBrandsToro ManualsRiding ProductsX30 GeoLink Precision Spray System Kit

FormNo.3412-170RevA

X25orX30GeoLink

PrecisionSpraySystemKit

SoftwareVersion4.00

QuickStartGuide

ContactToroNSNat1-844-GEOLINK(1-844-436-5465)orNSNTech@toro.comforcustomerservice.

Note:Whenyouturnonthemachinewiththedisplayinstalledforthersttime,thedisplayisinstandardmode.

Ensurethatthemachineisstoppedwhilechangingthedisplayconsoleandconguration.

UsingtheTouchScreen

Sprayerinformationisaddedtothescreenwhenyoutouchandenabletheindividualicons.

•Selectanyicononthescreentodisplaywhatisshownonthescreen.

•Pressonanicontochangeit,andfurtheroptionswilldisplay.

•Selecttheoptionsasrequiredandconrmthenewdisplay(Figure1).

g032674

Figure1

g204819

Figure2

X30Standard-ModeScreenShown

1.System-informationicon

6.Inventory-managericon11.Job-menuicon16.Map-layersicon

2.Guidanceicon7.Setupicon

12.Field-menuicon

17.Center-mapview

3.Job-informationicon8.Sprayerdashboard13.Quick-starticon

18.Boundary-selectionicon

4.Auto-sectioncontrolicon9.Master-switchicon

14.Zoom-functionicon19.Section-displayicon

5.Sprayer-controllericon

10.Receivercalibrationicon

15.Screen-viewicon

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3412-170*A

Summary of content (5 pages)

PAGE 1
Form No. 3412-170 Rev A X25 or X30 GeoLink® Precision Spray System Kit Software Version 4.00 Quick Start Guide Contact Toro NSN at 1-844-GEOLINK (1-844-436-5465) or NSNTech@toro.com for customer service. Note: When you turn on the machine with the display installed for the first time, the display is in standard mode. Ensure that the machine is stopped while changing the display console and configuration.
PAGE 2
Using the Standard Mode 4. Drive around the perimeter of the boundary. 5. When you are close to the beginning, select the complete boundary icon. Creating a Field Note: Create 1 field per course with all field Naming and Categorizing a Field Boundary boundaries for that course under that field. 1. Select the quick-start icon. 2. Select the field name, name the field, and confirm (Figure 3). Note: This is for RTK equiped machines only. 1.
PAGE 3
Nozzle 04 05 06 08 10 15 5. Nozzle Color Flow Rate Red 1.5 L/min (0.4 gpm) Brown 1.9 L/min (0.5 gpm) Gray 2.3 L/min (0.6 gpm) White 3.0 L/min (0.8 gpm) Blue 3.8 L/min (1.0 gpm) Green 5.7 L/min (1.5 gpm) Press the NOZZLE NAME icon (Figure 6). g201302 Figure 6 1. Navigate to the new-nozzle icon. 2. Select a nozzle based on size and color. 3. If desired, rename the nozzle. 4. Do not change the nozzle parameters.
PAGE 4
1. Fill the tank with water. Note: For the 1750 sprayers only, run the 2. Select the sprayer-controller icon and expand the sprayer-controller panel. valve-balance wizard before selecting a nozzle. 3. Select the correct nozzle. 3. Select the product title. Note: Nozzles are created in the standard 4. Select the custom product icon. mode; refer to Creating a Nozzle (page 2). 5. Name the product, select the rates, and select the rate increment (Figure 7). 4.
PAGE 5
g200319 Figure 9 5800 Sprayer Controls 1. Master section switch 2. Section switches g202822 Figure 10 1750 Sprayer Controls 1. Section switches 8. 2. Master section switch To start spraying, turn on the master-switch icon (the master-switch turns green) and drive into the spray area (Figure 2). Note: The machine starts spraying when the sprayer crosses into the correct spray area. Note: The display shows areas to be sprayed with light gray and non-spray areas with a dark gray.