Form No. 3397-155 Rev C GeoLink® Precision Spray System Multi Pro® 5800 Turf Sprayer Model No. 41623—Serial No. 315000001 and Up Model No. 41624 Model No. 41625 Note: Contact Toro® NSN® at 1-800-ASK-TORO or NSNTech@toro.com for customer service. Register at www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. g000502 Figure 1 1. Safety-alert symbol This manual uses 2 words to highlight information.
Safety Read and understand the contents of this Operator’s Manual before operating the console computer. • Keep these instructions with the Operator’s Manual for the turf sprayer. • It is very important that all who operate this equipment have ready access to these instructions at all times. • Read these instructions and the instructions in the Operator’s Manual for the turf sprayer carefully. Be familiar with the controls and the proper use of the equipment.
Product Overview Note: Hold the green button only to turn on the screen until the screen and light bar begins to flash, or in an emergency, to turn the screen off. Controls The GeoLink™ System consists of an ECU-based control console, GPS system, pressure transducer, and a turbine-type flowmeter. Become familiar with the controls before you start the engine and operate the sprayer.
Brightness-Control Buttons Brightness-control buttons adjust the brightness of the display (Figure 3). g030694 Figure 3 1. Help button 4. Brightness-control button 2. USB eject button 5. Brightness-control button 3. Home button 6. Day or night mode Cancel and Confirm Buttons Use these buttons to cancel or confirm an entry or a selection. You must select 1 of these buttons to progress from any screen displaying them (Figure 4).
Understanding the LED Lights Operation The display computer controls the spray application rate for varying vehicle speeds. You set the target volume per unit area to spray, and the display computer automatically maintains the flow within the proper range of the vehicle speed and continually displays the actual volume of material per area sprayed. The display computer also monitors the area sprayed, the speed of the vehicle, and the total volume of material sprayed.
Using the Touch Screen You add Sprayer information to the screen by touching and enabling the individual icons. • Select any icon on the screen to display what is shown on the screen. • Further options display when you press a particular icon. • Select options as required. • Confirm the new display (Figure 4). Using the Master Switch The master switch on the screen turns the sprayer system on (Figure 8). This switch does not work when the section switches or the foot switch is off.
Using the Easy Mode The easy mode is for spraying areas with defined boundaries, allowing you to select the jobs and display the spraying area. g030907 Figure 8 Easy-mode screen 1. System-information icon 5. Inventory-manager icon 9. Job-menu icon 13. Screen-view icon 2. Guidance icon 6. Setup icon 10. Field-menu icon 14. Center-map view 3. Job-information icon 7. Sprayer dashboard 11. Job-assistant icon 15. Boundary-selection icon 4. Sprayer-controller icon 8. Master-switch icon 12.
3. In the sprayer-controller screen, determine if the correct rate (gal/ac) is selected. 4. If the rate is not correct, change the rate with the preset rates, incrementally or selecting the current rate and manually entering the application rate (Figure 10). g031485 Figure 12 1. Job-menu icon 3. Select the job region 2. Configure-job regions icon 9. g031494 Note: Refer to the standard mode videos for Figure 10 spraying a boundary inside another boundary. 3. Decrease and increase icons 4.
If the display shows all light gray, you can spray every area. 5. 6. Select the field menu icon. Select the name of the existing field (Figure 16). Using the Easy Mode with an Existing Job Note: A job is set up in the standard mode. Ensure any previous job information is deleted before repeating an existing job. 1. Start the machine and keep the key in the RUN position. 2. Open the sprayer-controller icon (Figure 14). g031533 g031532 Figure 16 Figure 14 1. List of existing fields 1.
g030903 Figure 18 1. Boom switch, left boom 3. Boom switch, right boom g031535 2. Boom switch, center boom 10. Figure 19 1. Job-menu icon To start spraying, turn the spray icon on the screen and drive into the spray area (Figure 8). 2. Record-job information icon Note: The machine will start spraying when the sprayer crosses into the correct spray area. Note: The display shows areas to be sprayed as light gray and non-spray areas as dark gray.
g031536 Figure 20 1. Job-notes icon g031537 2. Job-information icon Figure 21 1. Job-menu icon Exporting Job Information 2. Data-exchange icon Note: Ensure a job is in session before exporting job information. 1. Insert a USB storage device into the left side of the console. 2. Select the the job-menu icon (Figure 21). 3. Select the data-exchange icon (Figure 21). 4.
Setting up the System Note: The pump should increase the pressure until it reaches the desired rate with the proper nozzle size. Before operating the GeoLink spray system, perform this procedure. 1. Read through the following instructions before starting. 2. Attach the supply hose to the anti-siphon tube and fill the tank half full of clean water. 11. Turn the master-boom control (foot) switch to the OFF position.
Operating Tips Note: The system should automatically correct the target application rate. If the system does not correct the application rate, review Setting up the System (page 13). 9. 10. Increasing the RTK Reception After spraying a swath, switch the foot switch to the OFF position to shut off the spray flow to all booms. Reduce the machine speed when you are approaching an area with known RTK reception difficulty. Note: This also shuts off the area calculations.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure • Clean the flowmeter (more often when using wettable powders). Every 200 hours Cleaning the Flowmeter 9. Service Interval: Every 200 hours 1. Thoroughly rinse and drain the entire spraying system. 2. Remove the flowmeter from the sprayer and flush it with clean water. 3. Remove the retainer ring on the upstream side (Figure 22).
Troubleshooting Note: If the console computer malfunctions or needs repair, you can control the system using the center-console controls. For many errors an error code, or trouble code, will display. It is also possible to view the errors on the screen. The errors listed below are common and are correctable. For other errors or if a problem persists, always record the error message to report to your distributor, including any code displayed.
Problem There is no power to the display. Possible Cause Corrective Action 1. The connectors are not installed correctly. 1. Ensure the connectors are installed correctly at the back of the display, 2. The fuse for the display is blown. 3. The battery connections are loose. 2. Replace the fuse. 3. Secure the battery connections. The monitor is frozen. 1. There is a malfunction with the software. 1. Hold in the green button on the back of the display until the front LED lights flash.
Notes:
Notes:
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
