Form No. 3411-496 Rev E X25 GeoLink® Precision Spray System Kit Multi Pro® 1750 or 5800 Turf Sprayer Software Version 4.00 and Up Note: Contact your authorized Toro distributor, Toro NSN at 1-844-GEOLINK (1-844-436-5465), or NSNTech@toro.com for customer service. Register at www.Toro.com.
This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Contents Safety ....................................................................... 3 Product Overview ....................................
Safety Product Overview Read and understand the contents of this Operator’s Manual before operating the console computer. • Keep these instructions with the Operator’s Manual for the turf sprayer. g204997 • It is very important that all who operate this Figure 2 X25 control console equipment have ready access to these instructions at all times. • Read these instructions and the instructions in the Operator’s Manual for the turf sprayer carefully.
Controls Become familiar with the controls before you start the engine and operate the sprayer. Floating-Menu Bar g203292 Figure 7 1. Power-down icon 2. Help icon 6. Home screen icon 7. Brightness-control (reduce brightness) icon 3. USB eject icon (displays when a USB storage device is inserted into the X25 monitor) 8. Brightness-control (increase brightness) icon 4. Screen-capture icon 9. Brightness mode (auto, day mode, and night mode) icon 5.
Note: Turning off the console correctly does not USB Eject Icon affect the data stored in the ECU memory. Press the USB EJECT icon before you remove a USB device from the X25 control console (Figure 7). The USB eject icon is available on the floating-menu bar only when you have a USB storage device inserted into the USB port. Note: The USB port (not shown) is located at the back of the monitor. Screenshot Icon Press the SCREENSHOT icon to record the current screen image onto the USB storage device.
Operation • Yellow—the boom section is on and not flowing intentionally (typically due to auto-section control stopping the flow). The computer in the automatic section controller (ASC) controls the spray application rate for varying vehicle speeds. You set the target volume per unit area to spray, and the ASC automatically maintains the flow within the proper range of the vehicle speed and continually displays the actual volume of material per area sprayed.
Selecting a Language and Accepting the License Agreement The screen that follows the splash screen displays the language selection and the EULA (end user license agreement). 1. If needed, press the languages icon to change the X25 display to a different language (Figure 14). Note: Setting the language in the EULA screen changes the language setting throughout the X25 user interface. You can also change the language in the User settings. g204034 Figure 13 Settings screen 1. Current access level 2.
When the master switch icon is red, press the icon to display the master switch status, which shows the number of active alarms (Figure 17). g203217 Figure 15 1. Selected language 3. 2. Confirm icon g205202 Read the EULA (Figure 14). Figure 17 Use the scroll bar to navigate to the bottom of the screen. The Yes icon will change to green (Figure 14). 4. At any time, press the confirm icon (Figure 17) to return to the main screen and complete the necessary corrective action.
Selecting the Correct Units of Measure 5. As needed, select the correct units and application rate, and press the confirm icon (Figure 20). The following options are available: Metric, Imperial (US), and Imperial (UK). The United States (US) and the United Kingdom (UK) imperial options are provided because gallons and fluid ounces have different measurements in the US and the UK. 1. Press the setup icon on the main screen (Figure 18). g204046 Figure 20 1. Current unit of measure g204035 Figure 18 1.
Using the Easy Mode Use the easy mode for spraying areas with defined boundaries, allowing you to select from the list of jobs and display the spraying area. g203493 Figure 21 Easy-mode screen 1. System-information icon 5. Inventory-manager icon 9. Job-menu icon 13. Screen-view icon 2. Guidance icon 6. Setup icon 10. Field-menu icon 14. Center-map view 3. Job-information icon 7. Sprayer dashboard 11. Quick-start icon 15. Boundary-selection icon 4. Sprayer-controller icon 8.
Using the Different Spraying Methods Spraying with a Field Boundary Setting Description This method allows you to spray or excludes you from spraying a job region defined by a boundary: within defined boundaries that are setup. You create the boundaries through the display in Standard Mode. ASC ON GeoLink controls the operation of the individual nozzle sections.
Spraying with an Unlimited Boundary Spraying with Rate Control Only This method allows you to spray any area and has no boundaries. This spraying method allows the following: This spraying method allows the following: • The GeoLink system controls the application rate. • The operator controls the boom sections. • The GeoLink system controls the nozzle sections with pass to pass control without any field boundary. • The GeoLink system controls the application rate. 1.
g209113 Figure 25 1. Auto-selection control-configuration icon (ASC) 3. ASC on/off icon 2. Sprayer-controller icon 4. Rate-control icon g204096 Figure 26 Creating a New Product Entry and Setting the Tank Volume Note: Ensure that the units are correct for your use. Refer to Selecting the Correct Units of Measure in the Operator’s Manual. 1. Sprayer-controller icon 3. ECU 1 icon 2. Expand icon 4. Product configuration icon 3. Press the ECU 1 icon (Figure 26). 4.
g204127 Figure 27 1. New product... icon 6. g204241 Figure 29 2. Product selection list icon Press the NEW PRODUCT... icon, and press the confirm icon (Figure 27). 4. Move cursor right icon 2. Backspace icon 5. Confirm icon 3. Move cursor left icon The New Product Setup wizard displays. 7. 1. Display keyboard 9. On step 1 of the new product setup dialog box, press the icon, and press the next icon (Figure 28).
g204244 Figure 32 1. New product setup dialog box 2. New product rate increment icon 3. Back icon (previous step) g205035 Figure 31 Sprayer control example 1. Increment rate lower 2. Increment rate higher 4. Preset rate 2 5. Flow rate increment 0.03 units higher A. 3. Preset rate 1 • Set a rate that you raise or lower application preset rates 1 and 2 by pressing the PRODUCT RATE INCREMENT icon (Figure 32). 15 4. Progress bar 5. Product rate preset icons 6.
g204317 Figure 33 g205038 Figure 34 1. Product-application rate field (example: 0.012 gal/kft2) 3. Confirm icon 1. Preset -application rate field 2. Numeric pad 2. Numeric pad B. B. Press the confirm icon (Figure 33). 11. • Press the 1 or set the preset product application rates as follows: (Figure 32). PRODUCT RATE PRESET PRODUCT RATE PRESET 2 icons to A. Use the numeric pad of the display to enter the preset application rate (Figure 33). 16 3.
2. Press the VOLUME icon (Figure 36). 3. Use the numeric pad of the display to enter 1 of the following: Note: Press the or icons to enter a preset increment of product volume quantity. INCREMENT VALUE DECREMENT VALUE g204276 g204329 Figure 37 Figure 35 1. Product configuration window 2. New product setup dialog box 12. 3. Confirm icon In the product configuration window, press the confirm icon to save the new product information (Figure 35). Press the TANK FILL 4. Numeric pad 5.
g204242 Figure 38 1. Old product tank volume 2. New product tank volume • If you are incrementally adding chemicals to g204245 water, enter the volume of water in the tank , press the confirm icon, and proceed to step 4. Figure 39 1. Volume increment icon 2. Decrease increment icon Note: The volume of water and product is less than or equal to the configured tank capacity. 4. 5. If you are incrementally adding chemicals to water, press the VOLUME INCREMENTS icon (Figure 40). 3.
Using the Easy Mode with a New Job Setting the Application Rate and Naming the Job 1. Start the machine and keep the key in the RUN position. 2. Open the sprayer-controller icon (Figure 41). g031532 Figure 41 1. Sprayer-controller icon g204243 Figure 40 Incrementally adding product 1. Volume of water in the tank (example: 100.00 gal) 5. 120.00 gal Volume of water and product in the tank plus an increment amount of product (example: 140.00 gal) 2. Increment amount of product icon (example: 20.
Selecting the Spray Nozzle—Preparing to Balance the Nozzle Valves Multi Pro 1750 Turf Sprayer Important: When the you create a job, the nozzle size to which the GeoLink system is adjusted is indicated on the display of the X25 control console. You must use the valve balance wizard each time you change spray nozzles. 1. Ensure that the agitation valve is adjusted and that the spray system pressure is above 207 kPa (30 psi); refer to your Operator's Manual. 2. Fill the sprayer tank with clean water. 3.
Note: If the nozzle that you are configuring is not in drop-down list, you will need to create a new nozzle in the setup menu before using the valve balancing wizard; refer to Creating a Nozzle (page 32). g205226 Figure 46 2. Valve balance wizard icon 1. Configuration icon Selecting the Spray Nozzle—Valve Balancing Wizard—Steps 1 through 3 Multi Pro 1750 Turf Sprayer 1.
6. At step 3 of the valve balancing wizard, If you need to set an different sprayer ground speed, press the speed icon (Figure 49). 7. Use the numeric pad to enter the ground speed at which you will spray, and then press the confirm icon (Figure 51). g205648 Figure 49 1. Application rate icon 5. 2. Speed icon Use the numeric pad to enter the application rate that you are configuring, and then press the confirm icon (Figure 50). g205230 Figure 51 1. Ground speed field 3. Confirm icon 2.
g205436 Figure 52 1. Next icon Selecting the Spray Nozzle—Valve Balancing Wizard—Steps 4 through 6 Multi Pro 1750 Turf Sprayer g205660 1. Adjust the engine speed until the target application rate is displayed in the dashboard of the X25 control console, and set the throttle-lock switch of the machine (Figure 53). Figure 53 1. Application rate (dashboard—X25 command console) 2. 23 2.
g205521 Figure 55 1. Previous and next section icons 2. Section On/Off icon (ON indicated) g205437 Figure 54 1. Lock icon (flow rate stabilized) 2. Next icon 3. Press the next icon (Figure 54). 4. At step 5 of the valve balancing wizard, perform 1 of the following: 4. Wait indicator 5. Master switch icon (ON—green) 3. Active section bypass adjustment indicator • The application rate for the section valve is too high (Figure 56).
g205524 Figure 57 1. Flow rate (e.g., below the 0.500 target rate) g205520 Figure 56 1. Previous and next section icons (inactive) 3. Flow rate (e.g., above the 0.500 target rate) 2. Section On/Off icon (OFF indicated) 4. Reduce the flow indicator (close the bypass valve) A. Press the section On/Off icon (Figure 56) to shut off the section valve (red). B. Move to the back of the machine. C. Adjust the bypass valve at section valve 1 to reduce the flow rate to the target application rate. 5. 2.
g205525 Figure 60 g205522 Figure 59 1. Next icon 7. When all of the section valves are balanced, select the next icon (Figure 59). 8. At step 6 of the valve balancing wizard, check the section valve balanced list to ensure that all the bypass valves are adjusted, and press the confirm icon (Figure 60). 1. Section valve balanced list (green—complete; red—incomplete) 3. Back icon 2. Scroll bar 4.
Selecting the Spray Nozzle 4. Multi Pro 5800 Turf Sprayer 1. In the new job menu, press the nozzle icon (Figure 62). Select the excluded regions that are not to be sprayed (bunkers, trees, hazards, etc.) (Figure 63). Note: Refer to the standard mode videos for spraying a boundary inside another boundary. Operating the Sprayer System of the Machine 1. Set the 3 section switches (located in the control console of the machine) to the ON position (Figure 64 and Figure 65). g205214 Figure 62 1.
g031532 Figure 66 1. Sprayer-controller icon g205685 Figure 65 Multi-Pro 5800 1. Left section switch 3. In the sprayer-controller screen, determine if the correct rate (gal/ac) is selected. 4. If the rate is not correct, change the rate with the preset rates, incrementally or selecting the current rate and manually entering the application rate (Figure 67). 3. Right section switch 2. Center section switch 2. Press the master-section switch on the machine. 3.
g203639 Figure 70 Multi-Pro 1750 1. List of existing fields 3. Right-section switch 1. Left-section switch g203549 Figure 68 2. Center-section switch 3. Field-menu icon 2. Field-list icon 7. Press the job-menu icon (Figure 69). 8. Select the existing job (Figure 69). g205685 Figure 71 Multi-Pro 5800 1. Left-section switch 3. Right-section switch 2. Center-section switch 10. g203772 Figure 69 1. List of existing jobs Note: The machine starts spraying when the 3.
Using the Standard Mode g205067 Figure 72 1. System-information icon 6. Inventory-manager icon 11. Job-menu icon 16. Center-map-view icon 2. Guidance icon 7. Setup icon 12. Field-menu icon 17. Boundary-selection icon 3. GPS-information icon 8. Sprayer dashboard 13. Quick-start icon 18. Boom-display icon 4. Auto-selection control-configuration icon 9. Master-switch icon 14. Zoom-function icon 5. Sprayer-controller icon 10. Receiver-calibration menu icon 15.
Calibrating the Compass 1. Select the receiver calibration icon (Figure 73). 2. Select the compass icon (Figure 73). g209126 Figure 74 6. Confirm the calibration (Figure 73). Creating a Field Note: Create 1 field per course with all field boundaries for that course under that field. A spray job can only stay within 1 field. It cannot spray boundaries between fields. 1. Press the quick-start icon. 2. Select the field name, name the field, and press the confirm icon (Figure 75).
Creating a Nozzle 1. Set the user access level to STANDARD ; refer to Understanding the Different Display Modes (page 6). 2. Press the setup icon home screen. 3. Press the implement icon, boom icon, and nozzles icon (Figure 76). in the lower left of the g204393 Figure 77 1. Factory template selection (nozzle) 2. Next icon (next step) Nozzle Table Nozzle 04 05 06 08 10 15 g204392 Figure 76 1. Nozzle setup screen 2. New nozzle... icon 4. On the nozzle setup screen, press the NEW NOZZLE...
Calibrating the Flow Meter Customer provided equipment: A graduated catch container (a container with 0.01 ml (1/2 fl. oz) increments is preferred). Preparing for the Calibration 1. Ensure that the sprayer tank is clean. 2. Fill the sprayer tank with at least 150 gallons of fresh water. 3. Ensure that the nozzles that you intend to test are in the active spray (down) position. 4. Engage the parking brake and start the engine. Note: Allow the engine and hydraulic system to warm for 10 minutes.
7. Turn on the sections using the master-section switch. 8. Perform the catch test for at least 15-seconds or more at 1 of the nozzles (Figure 82). Note: The length of the catch test depends on the size of the container, but more time is best. 9. 10. Shut off the master section switch, set the throttle to the slow position, and shut off the spray pump. Set the graduated container on a level surface and note the fluid volume (Figure 83).
Recording Job Details The job menu selects or sets up specific job information associated with the chosen area. Use this menu to store information and record and report activity. Recording Job Information 1. Press the job icon (Figure 86). g211486 Figure 84 1. Run the catch test. 13. 2. Verify the fluid amount. Confirm the flow cal factor (Figure 85). g203550 Figure 86 1. Job-menu icon 3. List of information to change 2. Record-job information icon g211487 2.
Recording Job Notes Exporting Job Information Use the notes area to record any information for each job. Note: Ensure that a job is in session before exporting 1. job information. Open the job-information icon (Figure 87). 1. Remove the cap for the USB port located below the power button (Figure 88). g203865 Figure 87 1. Job-notes icon 2. Job-information icon 2. Press the job-notes icon (Figure 87). 3. Enter the information and press the confirm icon. g212841 Figure 88 1. Cap 3.
g203551 Figure 89 1. Job-menu icon 3. Export job report to USB icon g203571 Figure 90 2. Data-exchange icon 1. Eject USB icon 4. Press the data-exchange icon (Figure 89). 5. Select the export Job Report to USB icon (Figure 89). 6. Deselect the following in the job-report options menu: 9. 10. • Auto adjust ranges • Task data 7. If required, select the create shape files option in the job-report options.
Setting up the System Before operating the GeoLink spray system, perform the following procedures: Note: The master section switch for the machine is at the following locations, refer to (Figure 91, Figure 92, or Figure 93). g205125 Figure 93 Master section switch—Multi Pro 1750 turf sprayer: Preparing the Machine g205126 Figure 91 Master section switch—Multi Pro 5800 turf sprayer, 2015 and before 1. Read through the following instructions before starting. 2.
D. Press the switch window icon for the sprayer controller menu. The current home screen and the sprayer controller menu switches position. E. Press the configuration icon in the sprayer controller submenu to display to configuration menu (Figure 95). g203964 Figure 94 1. Auto section control configuration icon 3. ASC icon (OFF) 2. ASC icon (ON) B. C. g203967 Press the ASC icon to OFF (Figure 94). Press the sprayer-controller icon (Figure 95). Figure 96 1. Configuration icon F. 2.
2. 3. Note: Ensure that either the ASC is OFF or the Press the switch window icon to return sprayer controller menu. (Figure 95). boundary limit set to UNLIMITED. Enter the desired application rate by using the pre-sets, increase or decrease icons, or by selecting the current-target application rate icon (Figure 98). 6. Select a target application rate. 7. Increase or decrease the vehicle speed by 2 km/h (1 mph). The system should automatically correct the target application rate.
Alarm List (cont'd.) Alarm Description No GPS The GPS signal is lost. Parameter mismatch Contact Toro NSN at 1-800-ASK-TORO or NSNTech@toro.com for customer service. Pressure high The pressure signal input has exceeded the alarm-point setting. Receiver disconnected The GPS receiver is not responding. Requested rate is zero The auto-rate control is enabled, the tank is On, the master switch is On, and the requested rate is zero. Tank empty The calculated tank volume has reached zero.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure • Clean the flowmeter (more often when using wettable powders). Every 200 hours Cleaning the Flowmeter 9. Service Interval: Every 200 hours 1. Thoroughly rinse and drain the entire spraying system. 2. Remove the flowmeter from the sprayer and flush it with clean water. 3. Remove the retainer ring on the upstream side (Figure 100).
Troubleshooting Note: If the computer in the X25 control console malfunctions or needs repair, you can control the sprayer system using the center-console controls of the machine. For many errors an error code, or trouble code, will display. It is also possible to view the errors on the screen. The errors listed below are common and are correctable. For other errors or if a problem persists, always record the error message to report to your distributor, including any code displayed.
Problem Possible Cause Corrective Action The machine is not shown on the screen. 1. The display screen has been moved. 1. Select the center-map icon on the main screen. The lights are not blinking on the GPS receiver located on the ROPS. 1. There is no power to the GPS receiver. 1. Ensure that the connectors are installed correctly. The pressure is not high enough. 1. The nozzle size used is incorrect. 1. Refer to the nozzle selection chart for the proper nozzle sizing. 2.
Notes:
Notes:
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
