Installation Instructions

ManualsBrandsToro ManualsSprayersExcelaRate Upgrade Kit, Multi Pro 5800 Turf Sprayer

FormNo.3405-472RevA

ExcelaRateUpgradeKit

MultiPro

5800TurfSprayer

ModelNo.41642

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

WARNING

Chemicalsubstancesusedinthespraysystemmaybehazardousandtoxictoyou,bystanders,animals,

plants,soils,orotherproperty.

•Carefullyreadandfollowthechemicalwarninglabelsandmaterialsafetydatasheets(MSDS)forall

chemicalsusedandprotectyourselfaccordingtothechemicalmanufacturer'srecommendations.For

example,useappropriatepersonalprotectiveequipment(PPE),includingfaceandeyeprotection,

gloves,orotherequipmenttoguardagainstpersonalcontactwithachemical.

•Theremaybemorethan1chemicalusedandinformationoneachchemicalshouldbeassessed.

•Refusetooperateorworkonthesprayerifthisinformationisnotavailable.

•Beforeworkingonaspraysystem,ensurethatthesystemhasbeentriplerinsedandneutralized

accordingtotherecommendationsofthechemicalmanufacturer(s)andthatallthevalveshavebeen

cycled3times.

•Verifythatthereisanadequatesupplyofcleanwaterandsoapnearby,andimmediatelywashoffany

chemicalsthatcontactyou.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Pressuretransducer1

Captting

Flangegasket1

Flowmeter1

Flowmetergasket2

Switch

Wireharness1

Installthekit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3405-472*A

Summary of content (16 pages)

PAGE 1
Form No. 3405-472 Rev A ExcelaRate Upgrade Kit Multi Pro® 5800 Turf Sprayer Model No. 41642 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils, or other property.
PAGE 2
Installing the Kit 1. Position the sprayer on a level surface, set the parking brake, stop the pump, stop the engine, and remove the key from the starter switch. 2. Disconnect the negative (-) battery cable from the battery. 3. Loosen the worm clamps that secures the manifold coupler to the agitation valve and section valve assembly (Figure 1). Figure 2 Figure 1 New flow meter shown 1. Worm clamp 4. Transducer clamp 2. Gasket 5. Cap 1. Pressure transducer 3. Cap fitting 2. Transducer clamp 4.
PAGE 3
9. Remove the plug from the dashboard (Figure 4). Figure 4 1. Switch 2. Plug 10. Install the switch into the hole (Figure 4). 11. Beneath the dashboard, connect the wire harness to the switch, then connect it to the machine wire harness. Note: The connector on the machine wire harness is tied back to the machine wire harness.
PAGE 4
Operation Using the ExcelaRate Software Note: You can use the software immediately after installing the kit. InfoCenter Home Screen Note: The following figure is an example screen; this screen is meant to show all of the potential icons that could appear on the screen while operating. When you start the machine, the home screen appears, displaying the corresponding icons that apply (i.e., the parking brake is engaged, the boom sections are in the On position, the operator is out of the seat, etc.).
PAGE 5
Active-Application Rate InfoCenter Main Menu Screen The active-application rate indicates the actual rate at which the sprayed product is being applied (Figure 5). Press and hold the button 5 (far right) on the InfoCenter to access the Main Menu screen. From the Main Menu screen, you can access the Set Rates screen, Settings screen, Calibration screen, Service screen, Diagnostics screen, or the About screen (Figure 6).
PAGE 6
Note: From the home screen, press and hold buttons 1 and 2 simultaneously to select Rate 1 or press and hold buttons 4 and 5 simultaneously to select Rate 2. Set Rates Screen To access the Set Rates screen, press button 2 on the Main Menu screen (Figure 6) until you reach Set Rates and press button 4 to select Set Rates (Figure 7). Note: From the Home screen, press and hold buttons 1 and 5 simultaneously to apply boost rate.
PAGE 7
Figure 10 Figure 11 Note: Volume indicates the current amount of liquid in the tank. The low-limit setting alerts you when the tank volume has fallen below the specified low-limit-tank volume. This setting can be turned on or off. You can increase or decrease agitation by pressing buttons 3 and 4. Change the InfoCenter protected menus as follows: 1. Press button 2 on the Display settings screen until you reach Protected Menus, then press button 4 to select Protected Menus (Figure 12).
PAGE 8
Figure 13 Figure 15 Turn the InfoCenter PIN on/off as follows: 1. Press button 2 on the Display settings screen until you reach PIN Settings, then press button 4 to select PIN Settings (Figure 14). 1. Digit 1 4. Digit 4 2. Digit 2 5. Enter PIN 3. Digit 3 3. From the PIN Settings screen, press button 4 to select PIN Entry and to turn the PIN on or off (Figure 16). Figure 14 Figure 16 2. Enter your PIN using buttons 1 to 4 and press button 5 when you complete the PIN (Figure 15).
PAGE 9
Figure 17 Figure 19 4. Enter your old PIN using buttons 1 to 4 and press button 5 when you complete the PIN (Figure 15). 1. Digit 1 4. Digit 4 2. Digit 2 5. Enter PIN 3. Digit 3 Note: The default PIN when you initially create your PIN is 1234. 6. Confirm your new PIN using buttons 1 to 4 and press button 5 when you complete the PIN (Figure 20). Figure 18 1. Digit 1 4. Digit 4 2. Digit 2 5. Enter PIN Figure 20 3. Digit 3 1. Digit 1 4. Digit 4 2. Digit 2 5. Enter PIN 3. Digit 3 5.
PAGE 10
Note: It is recommended to start the 15 second catch test at 2.75 bar (40 psi), then adjust from there. All boom sections must be on when performing the catch test. Boom-Width Settings The boom-width settings are pre-populated at the manufacturing plant (Figure 9). 8. Start at 2.75 bar (40 psi) and use the application-rate switch to adjust the spray pressure so a catch test yields the volume displayed for the selected nozzle color.
PAGE 11
Service Screen To access the Service screen, press button 2 on the Main Menu screen (Figure 6) until you reach Service, and press button 4 to select Service. Note: While spraying, you can view your current flow rate from the Service screen. 200 G034324 1 2 Figure 22 1. Increase the desired distance 2. Decrease the desired distance G034305 8. Ensure that the boom sections are off and press button 2 to begin calibration.
PAGE 12
Diagnostics Screen InfoCenter Spray-Area Screens To access the Diagnostics screen, press button 2 on the Main Menu screen (Figure 6) until you reach Diagnostics, and press button 4 to select Diagnostics. From the Home screen, press and hold button 5 to open the menu bar and select the Total Area or Sub-Area screen (Figure 27). Use the Total Area screen to track the total number of acres and gallons that you have sprayed across all areas (Figure 27).
PAGE 13
Figure 28 Sub-Area Screen 1. Active sub-area 4. Volume sprayed in the active sub-area (US gallons) 2. Area sprayed in the active sub-area (acres) 5. Select the previous sub-area; hold the button to reset area and volume sprayed for the active sub-area. 3.
PAGE 14
InfoCenter Advisories Operator advisories automatically display on the InfoCenter screen when a machine function requires additional action. For example, if you attempt to start the engine while pressing the traction pedal, an advisory displays, indicating that the traction pedal must be in the NEUTRAL position. For each advisory that occurs, there is a condition (e.g.
PAGE 15
Parameter Status 503 A value is outside the range of accepted values Parameter status, invalid data defaults used Booms Turned Off 802 Speed dropped Booms turned off, stopped or moving too slowly 15
PAGE 16