Installation Instructions

ManualsBrandsToro ManualsAttachmentsHitch Frame and Draw Bar Kit, Heavy-Duty Workman Vehicles

 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

H.D. Hitch Frame and Draw Bar Kit

Workman



Vehicles

Model No. 44213–210000001 and Up

Form No. 3352–626

Installation Instructions

Safety and Instruction Decals

93-8071

1. Hot surface/burn hazard—stay a safe distance from the hot

surface.

Installing the H.D. Hitch frame

and Draw Bar Kit

1. If a 2/3 or Full Size Bed is installed on vehicle, it must

be removed as follows:

A. With bed lowered, remove clevis pins and lynch

pins securing each cylinder rod end to bed

mounting plates (Fig. 1).

2/3 Bed Shown

Figure 1

1. Bed mounting plate

2. Cylinder rod end

3. Clevis pin

4. Lynch pin

B. Remove clevis pin and two lynch pins securing each

set of pivot plates to frame channels (Fig. 2).

Full Bed Shown

Figure 2

1. Vehicle frame channel

2. Pivot plate

3. Clevis pin

4. Lynch pin

C. Carefully remove bed from vehicle frame.

The bed and its accessories may weigh in excess of

200 pounds, so do not try to install or remove it by

yourself.

• Get the help of two or three other people.

Caution

Summary of content (8 pages)

PAGE 1
Form No. 3352–626 H.D. Hitch Frame and Draw Bar Kit Workman Vehicles Model No. 44213–210000001 and Up Installation Instructions Safety and Instruction Decals 93-8071 1. Hot surface/burn hazard—stay a safe distance from the hot surface. 4 Installing the H.D. Hitch frame and Draw Bar Kit 1. If a 2/3 or Full Size Bed is installed on vehicle, it must be removed as follows: A. With bed lowered, remove clevis pins and lynch pins securing each cylinder rod end to bed mounting plates (Fig. 1).
PAGE 2
Steps 2 and 8 only pertain to vehicles with serial numbers 240000001 and up. 6. Remove the quick coupler fittings and the 90 fittings from the rear hydraulic hoses (Fig. 5). 2. Remove the clamp securing the hoses to the R.H. rear frame rail (Fig. 3). 7. Install a new 45 fitting to each of the rear hydraulic hoses and re–install the quick coupler fittings (Fig. 5). Note: Make sure the O–rings are positioned in the fittings. 8.
PAGE 3
12. Remove two flange head capscrews and flange locknuts securing rear of each engine frame mounting bracket to each side of vehicle frame (Fig. 7). 16. Slide slots on bottom of draw bar assembly onto capscrews as shown in Figure 9. Pivot draw bar assembly upward and align top holes with holes in hitch assembly. Secure draw bar assembly to hitch assembly with two 1/2 x 4 inch large and locknuts. Tighten all fasteners. 2 3 1 1 Figure 9 Figure 7 1. Engine frame mounting bracket 1. Draw bar 2.
PAGE 4
18. Mount new spacer brackets to front of R.H. and L.H. bed frame channels with three capscrews and 3/8 inch locknuts. Position brackets on channel as shown in Figure 11. 1 2 Full Bed Shown Figure 13 1 1. Left rear corner of bed 2. Pivot bracket 2/3 Bed Only Figure 11 1 1. Spacer bracket 19. Remove capscrews and locknuts securing each set of rear pivot plates and pivot tube to right and left bed frame channels (Fig. 12). 1 2 2/3 Bed Shown Figure 14 1. Left rear corner of bed 2. Pivot bracket 21.
PAGE 5
HITCH RATING MAXIMUM TONGUE WEIGHT: 400 LBS (181 KG.) MAXIMUM TRAILER WEIGHT: WITHOUT TRAILER BRAKES; 1500 LBS (680 KG.) WITH TRAILER BRAKES; 3500 LBS (1587 KG.
PAGE 6
PAGE 7
PAGE 8