FORM NO. 01-502-1400Rev. A OPERATOR'S MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone else using or maintaining this making are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety massages.
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS . SAFETY AND INSTRUCTION DECALS SPECIFICATIONS .. SET UP INSTRUCTIONS OPERATING INSTRUCTIONS 11-13 MAINTENANCE. . 14 Page STORAGE .. i 14 IDENTIFICATION AND ORDERING 14 HYDRAULIC SCHEMATIC .. 15 ELECTRICAL SCHEMATIC. 16 THE TOR PROMISE .. Back Cover SAFETY INSTRUCTIONS The safety alert symbol means CAUTION, WARNING or DANGER "personal salty instruction”. Read and understand the instruction because it has to do with safety.
SAFETY INSTRUCTIONS (Continued) WHILE OPERATING 8. Using the machine demands attention. Failure to operate vehicle safely may resulting an accident, tip over of vehicle, serious injury or death. Drive carefully. To prevent dipping or loss of central: A. Use extreme caution, reduce speed and maintain a safe distance around sand traps, ditches, creeks, ramps, any unfamiliar areas or other hazards. B. Watch for holes or other hidden hazards, C. Use caution when operating vehicle ona steep slope.
SPECIFICATIONS Ball Height: ground. Bali Size: 2" Diameter Rated Capacity: 400 max. trailer tongue wt. max. trailer gross wh. wio brakes max. trailer GVW brakes Construction: Welded Steel hitch plate with rubber isolated ball. Rear Stabilizer: Fastens to Workman axe. Welded steel construction. Workman Mounting Zone: 2/3rd area of Workman cargo zone. Shipping Weight: 80lbs Brake Controller: Electric controller with variable output to adjust braking force.
SET UP INSTRUCTIONS {Continued} Wire Harness — Connector Bracket Access Controller Wheel Main Frame L /)’7 work Man " < «* Rear Axle h. Rear Stabilizer ; Figure 2 Left Side / WORKMAN Frame Front /C// Bracket Att.
SET UP INSTRUCTIONS (Continued) E. Route wire harness alongside main vehicle wire harness toward rear of vehicle. Attach connector end of harness to (92-4524) connector racket with fasteners. Atlas threaded connector cover chain to one of the fasteners., F. Secure wire harness to Workman in several places with wire ties. G. Connect battery.
SET UP INSTRUCTIONS (Continued) / Plate Leach Pin R-Clamp P\ Manual WORKMAN ] iw Tube Frame Cap screw, Flat Washer Lock Washer A /{ Bracket /qt/ Mount Lynch Pm | ‘grue \»§f ~ Clevis Pin ; T~ Figure 4 Huger 7/1 6"x Cap screw Lock Nut \ “SAE" Lat j/ Wife S her racket Flat Washer ~ Washer \ 1/“‘ Figure 7
SET UP INSTRUCTIONS {Continued) INSTALL MALE QUICK COUPLE R-CUSHMAN IMPLEMENTS Bushman 5th wheel implements use one male and one female quick couplet 1o power their 5th wheel implements. Two male couplets are requited ta function with the Workman remote hydraulic kit. it is necessary to replace the female quick couplet of the Bushman 5th wheel implement with a male quick couplet. 1.
OPERATING INSTRUCTIONS Safe operation begins before taking the vehicle out for a day's work. Read and understand the operating instructions for the Toto Workman, bih wheel hitch kit, and 5th wheel implement before using the equipment. Allow only rained operators o use the vehicle. Caution The interlock switches are for the operator’s protection, so do not bypass hem. Check operation of the switches daily to assure interlock system is operating on the Workman.
OPERATING INSTRUCTIONS (Continued) 10. Connect the electric brake wire harness of the sth wheel implement to electrical connector located at left side of Workman frame. Route wire harness near the ball and through the wire bracket ina manner that will prevententanglementwith the Workman, yet provide sufficient slack to allow turns in either direction. Secure wire harness to 5th wheel implement tongue with plastic tes. A\ DANGER Jack-knifing or sliding could cause loss of control resitting in serious injury
OPERATING INSTRUCTIONS (Continued) 2. Adjust the brake output control by initially setting at approximately 3/4 of the gravel from MINIMUM towards MAXIMUM. With this adjustment, make a few slow speed test stops on dry pavement. Slide the control towards MAXIMUM for firmer braking and towards MINIMUM for lighter braking until the brakes are set just short of skidding on dry pavement. If uncertain about the adjustment, leave slide control setting at MAXIMUM. 3.
MAINTENANCE 1. Always stop Workman engine and set parking brake before performing any maintenance activity on either the Workman or Bth wheel implement, 2. Lower the 5th wheel implement to the ground or against its unlatch pins to prevent accidental towering during maintenance. The Workman engine does not need to be running to lower the 5t wheel implement. 3. The engine access cover of the 5th wheel can be removed hy unscrewing the two knobs and filing the cover off the 5th wheel hitch plate.
The Toto Bromine A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The Hollowing time periods from the date of purchase apply. Commercial Products The costs of parts and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25", 1f you feel your TOR products defective and wish to rely an The Toto Promise, the following procedure is recommended: 1.
