Form No. 3433-937 Rev C Sulky Mid-Size Mowers Model No. 44401—Serial No. 400000000 and Up Register at www.Toro.com.
Write the product model and serial numbers in the space below: WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Model No. Serial No. This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
Safety • Ensure that you operate the sulky in areas where there are no obstacles nearby. Failure to maintain adequate distance from trees, walls, and other barriers may result in injury as the sulky backs up or turns during operation if the operator is not attentive to the surroundings. Operate the sulky only in areas where there is sufficient clearance for you to safely maneuver the sulky. • Ensure that the sulky is properly attached to the machine and is in good working order prior to use.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal140-1917 140-1917 1. Crushing hazard of legs—read the Operator’s Manual; do not turn more than 90°; do not stand on the attachment while moving in reverse; look behind you when moving in reverse. decal116-8225 116-8225 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Mount plate Bolt Nut Pivot pin Hairpin cotter Transport pin Sulky 1 4 4 1 1 1 1 Install the sulky. Important: A Weight Kit is required for 91 cm (36 inch) machines and is optional for other sizes. Contact your Authorized Service Dealer to obtain the kit, and install it before installing the sulky.
g295053 Figure 4 g315914 Figure 2 2. 3. Store the transport pin in the pin plate shown in Figure 5. Important: Do not store the transport pin in the drawbar tube while operating the machine. Attach the sulky to the bracket using the pivot pin and hairpin cotter (Figure 3). Note: Ensure the J end of the pin rests on top of the plate (Figure 4). g294868 Figure 5 g315915 1. Transport pin Figure 3 1. Pivot pin 3. Hairpin cotter 2. Sulky 6 2.
Operation WARNING You could fall off the platform and be seriously injured during operation. Do not move the machine forward unless you are standing with both feet on the platform and your hands are holding onto the reference bars. Step off the platform when moving the machine in reverse. Using the Sulky Step onto the sulky platform before starting the machine. Use the reference bars on the machine to stabilize yourself while riding on the platform. g315917 Figure 6 1.
Maintenance Greasing the Sulky Service Interval: Before each use or daily—Inspect the grease fittings. Every 40 hours—Grease the platform (grease immediately after each washing). Grease type: General-purpose grease 1. Park the machine on a level surface, disengage the PTO, and engage the parking brake. 2. Shut off the engine and remove the key. 3. Clean the grease fittings with a rag. Note: Make sure to scrape any paint off the front of the fitting(s). 4. Connect a grease gun to the fitting. 5.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
