FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged 1o read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page Page SAFETY INSTRUCTIONS 3-4 MAINTENANCE 9 SAFETY AND INSTRUCTION DECALS. .8 TROUBLE SHOOTING . 10 SPECIFICATIONS .6 STORAGE .M BEFORE OPERATING .. .7 IDENTIFICATION AND ORDERING " OPERATING INSTRUCTIONS . . 8 MAINTENANCE RECORD. . LUBRICATION . ...hoes 8 THE TOR PROMISE SAFETY INSTRUCTION The safety alert symbol means CAUTION, WARNING or DANGER “personal safety instruction”. Read and understand the instruction because it has to do with safety.
SAFETY INSTRUCTIONS (Continued) 8. Operator must be skilled and trained in how to drive on hillsides. Failure to use caution on slopes or hills may cause loss of control possibly resulting in personal injury or death. 8. If engine stalls or machine loses headway and cannot make it to the top of a slope, do not turn machine around. Always back slowly straight down the slope. 10. Do not carry passengers on the machine or tractor and keep everyone away from the areas of operation. 11.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. Replace any decals that becomes damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor. A DANGER » ROTATING PULLEYS AND BELTS CAN CAUSE IMUS INJ GUARDS ARE IN PLACE. 14 ON BELT GUARD {Part No. 01-506-0010) YU .
SPECIFICATIONS HITCH: Standard 3 point hitch WHEELS: Castor type, POWER: Tractor (16-25 HP) PTO drive at DIRECTIONAL CHUTE: All steel, over center 540-600RPM (Belt to Impeller) locking, spring tension control, operated . from tractor seat FRAME: All welded steel construction DIMENSIONS: Width 36" handle BEARINGS: Self sealed, self aligned Length Height 46" chute in IMPELLER: 10 bladed, reinforced, 24" .
BEFORE OPERATING ATTACH BLOWER TO TRACTOR IMPORTANT: The maximum PTO speed is 540 RPM. Do not operate ata faster speed because the fan, sprockets and PTO will be damaged. 1. Connect the PTO half {1 3/8" splines slip clutch) to the actor. When new, the spring lock lever on the end of the PTO is hard to operate. Apply grease and work the lever until it snaps in and out freely. In the correct position the lever will spring back out and lock the two shafts together.
OPERATING INSTRUCTIONS IMPORTANT: The maximum PTO speed is 540 RPM. Do not operate ata faster speed because the fan, sprockets and PTO will be damaged. 1. Start tractor engine and run at a low RPM. Slowly engage the PTO. 2. Run actor engine 10 1100 RPM, 3. Practice blowing material. Iris advisable to blow the same direction the wind is blowing to prevent material from blowing back into the cleared area.
MAINTENANCE ADJUSTING BELT DRIVE (Fig. 3} Make sure belt is properly pensioned to assure correct operation of unit and unnecessary wear. 1. To adjust tension: A. Remove the belt guard. B. Loosen the nuts mounting both bearings. C. Turn the nut on the Push Bolt (A} unit proper tension is achieved. The belt should have 1/8" deflection with 5 Ibs. of force. Keep track of the number of rns on the nut. . Turn the nut on the Pull Bolt (B) the exact number of turns that were used on the Push Bolt.
TROUBLE SHOOTING CONDITION CAUSE * CORRECTION FAN QUIT TURNING Remove belt guard. Check for broken belt or tension of the belt. Check PTO for sheared bolt. Check the drive shaft A key may be sheared. Replace belt or adjust the tension of the adjustments in manual} Replace the obit. Replace key. EXCESSIVE VIBRATION Check bearings on fan shaft for damage. ook into opening of deflector, check for material build up on fan blades. Replace bearings. Clean off any build up inside the housing.
STORAGE 1. Thoroughly clean the blower. The fan housing should be free of dirt, leaves and debris. 2. Check all fasteners for looseness: tighten as necessary. 3. Grease or oil all grease fittings and bearings. Wipe off excess lubricant. 4. Check the tension and condition of the belt. Adjust the tension if necessary. IDENTIFICATION AND ORDERING MODEL AND SERIAL NUMBER The DEBRIS BLOWER 2673 has two identification numbers: a model and serial number.
The Toto . Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The Following time periods from the date of purchase apply: Commercial Products The costs of parts and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25°. 1 you feel your TOR product is defective and wish to rely an The Toto Promise, the following procedure is recommended: 1.