FORM NO. 01-502-0410.2 MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS 3-4 SAFETY AND INSTRUCTION DECALS . LUBRICATION . 12 TROUBLESHOOTING . SPECIFICATIONS STORAGE .14 BEFORE OPERATING IDENTIFICATION AND ORDERING .. 14 Attach Blower To 300 Series Grounds master .6-7 MAINTENANCE CHART 15 Attach Blower To 200 Series Grounds master 8 11 THE TOR PROMISE Back Cover OPERATING INSTRUCTIONS 12 SAFETY INSTRUCTIONS The sateen/ alert symbol means CAUTION, WARNING OR DANGER"personal safety instruction”.
SAFETY INSTRUCTIONS (Continued) 8. Operator must be skilled and trained in how to drive on hillsides. Failure to use caution on slopes or hills may cause loss of control possibly resulting in personal injury or death. 9. If engine stalls or machine loses headway and cannot make it to the top of a slope, do not turn machine around, Always back slowly straight down the slope. 10. Do not carry passengers on the machine or Grounds master” and keep everyone away from the areas of operation. 11.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. Replace any decals that becomes damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor.
SPECIFICATIONS POWER: PTQ from Grounds master CASTORS: Swivel castors 4.10x3.5x4 FRAME: All welded steel construction BEARINGS: 2 self sealed and self aligning IMPELLER: 10 bladed, 24" diameter, welded and balanced DIRECTIONAL CHUTE: (Standard) All steel over center locking, spring loaded DIMENSIONS: Height: 36 Length: 36, 24" without handle Width: 48" with directional chute in down position SHIPPING WEIGHT: 245 ibs. CFM: Approx.
BEFORE OPERATING (Continued) 13. Have a helper push down the right push arm; 8. Install the Hydraulic Bracket (part number then remove the 2" x 4" blocks of wood, 2) in the same location with existing hardware. 14. Attach the PTO of the Grounds master to the PTO Adapter on the blower fan shaft. | 15. Using the lift mechanism on the i NOTE:This Bracket Grounds master, lower the unit on a level surface. &5 Uninstalled T When Mounting Blower 16.
BEFORE OPERATING (Continued) ATTACH BLOWER TO 200 SERIES GROUNDS MASTERS 1. Remove the cutting unit or other attachment trim the Grounds master. Refer to cutting unit or attachment operator’s manual. 2. Attach the Deflector Handle on the blower housing using the 1/2" x bolt. 3. Attach the linkage rod to the top hole in the Deflector Handle. Secure with flat washers and a 1/8" x 17 cotter pin. 4. Position the Grounds master to the rear side of the blower. 5.
BEFORE OPERATING (Continued) GROUNDS MASTER 220-D and 223-D (Fig. 4) 1. Attach the support bracket (A} to the steering column housing. Secure the bottom four holes with Debris Blower 2670 Grounds master 3/8 x bolts. Secure the two top side holes with 1/4 x 3/4" bolts.
BEFORE OPERATING (Continued) ONE PIECE CARRIER FRAME ALL 200 4, Line up the holes in the Grounds master SERIES (Fig.5) with the holes in the mounting frame (B). Phil up the mounting frame and secure 1. Remove the lift arms from the Grounds master. with the mounting pins. Attach a presto Deter to the mowing deck operator's manual. pin in each end of the mounting pins. 2. Install the mounting frame to the lower 5.
BEFORE OPERATING (Continued) TWO PIECE CARRIER FRAME ALL 200 2. Line up the holes in the mounting frame (B) to SERIES (Fig.6) the right and left lift arms on the Grounds master. 1. Install the mounting frame to the lower 3.Secure with the existing bolts on the tube (A) on the blower using the lower Grounds master. mourning pin to attach.
OPERATING INSTRUCTIONS 1. Start the Grounds master and run at a low RPM. 2. Lower the blower using the Grounds master lift mechanism. 3. Engage the PTO while the engine is at idle speed. 4. Increase the PTO speed to 1800 RPM. 5. Practice blowing material. [tis advisable 1o blow the samey direction the wind is blowing to prevent material from blowing back into the cleared area. TRANSPORTING BLOWER 1. Reduce the engine speed to idle position. 2. Disengage the PTO and wait for the PTO to stop. 3.
TROUBLESHOOTING CONDITION CAUSE CORRECTION FAN QUIT TURNING {200 Series) Belt may be loose or broken. {200 Series) Bearing pressed in the bearing mount may be damaged. {300 Se rigs) Bolt on PTO adapter may be sheared. Replace bet or adjust the tension of the belt. Replace the bearing, use #8609 locate when replacing. Replace bolt. EXCESSIVE VIBRATION Bearings on tan shaft may be damaged. Material may be built up on fan blades. RPM of the PTC shaft too fast. Replace bearings.
STORAGE 1. Thoroughly clean the bower. The fan housing should be free of dirt, leaves and debris, 2. Lubricate aii grease fittings. Wipe off any excess lubricant. 3. Place alight coat of grease on the splines of the PTO adapter. 4. Tighten all fasteners. IDENTIFICATION AND ORDERING MODEL AND SERIAL NUMBER. The BLOWER 2670 has two identification numbers: a model number and serial number. The two numbers are stamped on & plate which is located on the housing.
Ohe Outwore Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The following time periods from the date of purchase apply: Commercial Products .. The casts of parts and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25", K you feel your TOR product is defective and wish to ray on The Toto Promise, the following procedure is recommended: 1.