Installation Instructions

ManualsBrandsToro ManualsAttachments67 Blower Mounting Kit, Groundsmaster 220D

1 67-002-2952 Bearing Mount Assembly

(Incl. Ref. #2,3,4,25,26) 1

2 67-005-2822 Bearing Mount 1

3 01-100-0340 Bearing (see note) 1

4 67-004-2731 Pulley Shaft 1

5 3256-6 Flat Washer 1

6 3253-7 Lock Washer 2

7 3217-9 Hex Nut 2

8 01-260-0150 Sheave 1

9 01-260-0240 Bushing 2

10 82-004-1171 Key 3

11 01-260-0060 Sheave 1

12 01-264-0350 Belt 1

13 67-005-0241 Belt Guard 1

14 58-6520 Decal - Grease 1

15 01-506-0130 Decal - Danger 1

16 01-506-0040 Decal - Danger 1

17 01-650-1090 All Thread 1

18 32153-2 Lock Nut 1

19 3256-4 Flat Washer 1

20 3296-39 Lock Nut 1

21 01-282-0600 PTO Assembly 1

22 322-13 Capscrew - Hex Hd. 1

23 3217-6 Hex Nut 2

24 01-163-0030 Socket Head Set Screw 1

25 01-215-0050 Grease Zerk 1

26 95-0075 Ring - Retaining 1

Note: When installing bearing,

apply #609 Loctite to bearing

before pressing into collar.

PARTS LIST &

ASSEMBLY

INSTRUCTIONS

67 BLOWER MOUNTING KIT

for 220D SERIES GROUNDSMASTER

MODEL NO. 44533

FORM NO. 01-505-1331 Rev. B

DRIVE SYSTEM

67-005A

Ref.

No.

Part No.

Description

No.

Used

Ref.

No.

Part No.

Description

No.

Used

The TORO Company - 1996

All Ri

ese

Summary of content (8 pages)

PAGE 1
FORM NO. 01-505-1331 Rev. B PARTS LIST & ASSEMBLY INSTRUCTIONS MODEL NO. 44533 67 BLOWER MOUNTING KIT for 220D SERIES GROUNDSMASTER® Note: When installing bearing, apply #609 Loctite to bearing before pressing into collar. DRIVE SYSTEM Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No. No. Used Description 67-002-2952 Bearing Mount Assembly (Incl. Ref.
PAGE 2
MOUNTING FRAME 2 Ref. No. Part No. 1 2 3 4 5 6 7 8 9 10 67-005-2572 67-004-1161 01-159-0010 67-004-2261 325-6 3256-6 3253-7 3217-9 67-005-2411 67-005-2421 Description Mounting Frame Lower Mounting Pin Presto Pin Stop Bracket Capscrew - Hex Hd. Flat Washer Lock Washer Hex Nut Support Arm Support Bracket No. Used Ref. No. Part No.
PAGE 3
COUNTER BALANCE Ref. No. 1 2 3 4 5 6 7 8 9 10 Part No. 72-9240 322-12 3296-44 32128-35 3256-24 46-3380 66-8440 66-8420 66-8390 70-7940 Description Bracket - Extension Capscrew - Hex Hd. Lock Nut Flange Lock Nut "SAE" Flat Washer Bolt - Shoulder Link - Knee End - Spring Spring - Extension End - Spring No. Used Ref. No. 1 2 2 4 2 2 1 1 1 1 11 12 13 14 15 16 17 18 19 Part No. 70-7970 283-69 55-4300 3290-355 93-8074 66-8460 70-7920 12-3270 3234-29 67SPRG-A Description No.
PAGE 4
ASSEMBLY INSTRUCTIONS 67 BLOWER MOUNTING KIT NOTE: Refer to page 1, "DRIVE SYSTEM", during steps 1 thru 9. NOTE: Refer to page 2, "MOUNTING FRAME", during steps 10 thru 14. 1. Mount the bearing mount assembly (item #1) to the rear housing as shown on page 1. Fasten the bottom bolt with a 1/2" lock washer (item #6) and hex nut (item #7). Tighten but leave nut loose enough to pivot. Fasten the top bolt with a 1/2" flat washer (item #5), lock washer (item #6) and hex nut (item 7). Leave nut loose. 10.
PAGE 5
ASSEMBLY INSTRUCTIONS (Continued) BLOWER MOUNTING ON GM223D, GM225, GM1000L w/HYDRAULIC COUNTERBALANCE 2. Refer to the deck operator manual on the installation of these arms. If you have a GM200 series or GM1000L unit with a 62" Recycler deck mounted to it, you will need to do the following: 3. Mount the blower following the instructions outlined in the blower’s operator manual. 1. Order lift arms, part numbers 76-3080 & 76-3090, to replace the push arms on the traction unit. 4.
PAGE 6
NOTES 6
PAGE 7
NOTES 7
PAGE 8
MAINTENANCE RECORD Date