Installation Instructions

ManualsBrandsToro ManualsCommercial Debris BlowerWorkman MD/MDX/MDE Bed Mount Kit, Pro Force Debris Blower

FormNo.3366-333RevB

Workman

MD/MDX/MDEBedMountKit

ProForce™DebrisBlower

ModelNo.44543—SerialNo.311000001andUp

ModelNo.44544—SerialNo.311000001andUp

ModelNo.44545—SerialNo.311000001andUp

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

PreparetheProForce.

Skidmount

Flangenut(3/8inch)

Bolt(3/8x3inches)

Carriagebolt(3/8x1inch)

InstalltheskidplatestotheProForce.

Frictionlockplate4

Mountingbracket4

Flangenut(3/8inch)

Carriagebolt(3/8x1inch)

Carriagebolt(3/8x2inches)

InstalltheProForceon2010andolder

mid-dutyvehicles.

Bedrail2

Bedstake4

Spacer

Flangebolt(1/4x1-1/4inches)

Flatwasher(1/4inch)

Flangenut(1/4inch)

Carriagebolt(3/8x1inch)

Flangenut(3/8inch)

Carriagebolt(3/8x1-1/2inches)

InstalltheProForceon2011andnewer

mid-dutyvehicles.

Stake

Lockingplate4

Flangenut(3/8inch)

Carriagebolt(3/8x1inch)

InstalltheProForceonheavyduty

vehicles.

Purchasecorrecthardware

InstalltheProForceonuniversal

vehicles.

Positionindicator1

Rivot3

Chutebracket

Carriagebolt(10-24x5/8inches)

Nozzlemount2

Locknut(10-24)

Hitchpin2

Flangenut(1/4inch)

Extensionshell2

Nozzlekeel2

Bolt(1/4x3/4inches)

Installtheextension.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3366-333 Rev B Workman® MD/MDX/MDE Bed Mount Kit Pro Force™ Debris Blower Model No. 44543—Serial No. 311000001 and Up Model No. 44544—Serial No. 311000001 and Up Model No. 44545—Serial No. 311000001 and Up Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 Preparing the ProForce™ 5 No Parts Required Procedure Remove the tires, tow hitch, fenders and the stub axles from the ProForce trailer. 2 1 2 3 Installing the Skid Plates to the ProForce 1. Flange nut (3/8 inch) 2. Short tube hitch 3. Bolt (3/8 x 3 inches) Parts needed for this procedure: 2 Skid mount 6 Flange nut (3/8 inch) 2 Bolt (3/8 x 3 inches) 4 Carriage bolt (3/8 x 1 inch) 4 1 G014238 Figure 1 Mid-duty machines 4. Left hand skid plate (Mid-Duty shown) 5.
PAGE 3
1 2 3 4 3 Installing the ProForce on 2010 and Older Mid-Duty Vehicles 6 2 1 5 4 3 Parts needed for this procedure: 4 Friction lock plate 4 Mounting bracket 16 Flange nut (3/8 inch) 8 Carriage bolt (3/8 x 1 inch) 8 Carriage bolt (3/8 x 2 inches) G014237 Procedure Figure 3 Mid-duty vehicles 2010 and older 1. Remove the end gate attached to the bed of the vehicle. 1. Carriage bolt (3/8 x 2 inches) 2. Friction lock plate 2. Install the ProForce unit into the bed of the vehicle. 3.
PAGE 4
3. For mid-duty vehicles 2011 and newer, install the bed rails to the side of the bed with 8 flange bolts (1/4 x 1-1/4 inches) and 4 flange nuts (1/4 inch) (Figure 4). 5 4. Install the 4 bed stakes to the bed rails with 4 spacers, 8 carriage bolts (3/8 x 1-1/2 inches) and 8 flange nuts (3/8 inch) (Figure 4). Installing the ProForce on Heavy Duty Vehicles 5.
PAGE 5
1 2 3 7 4 Installing the Extension Parts needed for this procedure: G014241 Figure 6 1. Flange nut (3/8 inch) 2. Locking plate 3. Carriage bolt (3/8 x 2 inches) 4. Locking plate assembly 1 Position indicator 3 Rivot 2 Chute bracket 4 Carriage bolt (10-24 x 5/8 inches) 2 Nozzle mount 4 Locknut (10-24) 2 Hitch pin 10 Flange nut (1/4 inch) 2 Extension shell 2 Nozzle keel 10 Bolt (1/4 x 3/4 inches) Procedure 6 1.
PAGE 6
1 2 2 1 3 3 1 1 4 2 G014243 Figure 8 1. 1-1/8 inches (28.5 mm) 2. 3-1/4 inches (82.5 mm) G015436 3. Drill 1/4 inch holes (4) Figure 7 1. Extension shells 2. Bolt (1/4 x 3/4 inches) 3. Nozzle keel 4. Flange nut (1/4 inch) 3. For 2010 and older machines, drill the three 1/4 inch holes shown in Figure 9 for the position indicator. 4. Install the position indicator with the 3 rivots (Figure 10). 2. For 2010 and older machines, drill the four 1/4 inch holes shown in Figure 8 for the chute brackets.
PAGE 7
1 2 1 3 4 5 2 6 7 8 G014242 Figure 10 3 1. 2. 3. 4. 4 5 5 G014240 Figure 9 1. 4-3/8 inches (111 mm) 2. Drill 1/4 inch hole 3. 4-3/4 inches (120.6 mm) 4. Drill 1/4 inch hole 5. 55 degrees 5. Loosely install both chute brackets to the nozzle with 4 carriage bolts (10–24 x 5/8 inches), 2 nozzle mounts and 4 locknuts (10-24) (Figure 10). 6. Install the extension onto the nozzle and attach it with the hitch pins. Tighten the chute brackets once the extension is installed (Figure 10).
PAGE 8