Form No. 3394-198 Rev A Pro Force® 데브리 블로워 !" #$% 일련번호315000001및 및 그 이상 모델 번호44552—일 등록처www.Toro.com.
이 제품은 모든 관련 유럽 법규에 일치합니다. 자세 한 내용은 각 제품의 구체적인 적합성 선언서(DOC)를 참조하십시오. 주의 규제 준수 책임 당사자가 명시적으로 승인하지 않 은 개조 또는 변경을 실시하면 장비를 작동할 수 있 는 사용자의 권한이 무효가 될 수 있습니다. 중요: 이 엔진에는 스파크 방지 머플러가 장착되어 있 지 않습니다. 산림, 덤불 또는 목초 지대에서 엔진을 사 항 용 하 거 나 운 전 하 면 캘 리 포 니 아 공 공 자 원 법 4442항 을 위반 (California Public Resource Code Section 4442)을 하는 것입니다. 다른 주나 연방 지역에도 유사한 법 이 있을 수 있습니다. 이 스파크 점화 시스템은 캐나다 ICES-002를 준수합 니다. 경고 소개 캘리포니아 Proposition 65 경 고 본 제품은 캘리포니아 주에서 암, 선천성 기 형 및 기타 생식 기능 장애를 일으키는 것으 로 알려진 화학 물질이 들어 있습니다.
진단 모드 종료하기 .............................................28 그림2 1. 안전 경고 기호 본 설명서에서는 2개의 단어를 사용하여 정보를 강 조합니다. 중요는 특별한 기계 정보에 대한 주의를 환기시키며 참고는 특별히 유의해야 하는 일반 정보 를 강조합니다. 목차 안전 ............................................................................ 4 안전 작동 수칙 ..................................................... 4 안전 및 교육용 전사지 ......................................... 6 설정 ............................................................................ 7 1 배터리 연결 ...........................................
안전 • 위험 통제 및 사고 예방은 장비의 운전, 운송, 유지보수 및 보관을 담당하는 개인의 인식, 관심 및 적절한 교육 에 의해 좌우됩니다. 장비의 부적절한 사용이나 유지보 수는 상해나 사망을 초래할 수 있습니다. 상해나 사망 가능성을 줄이려면 다음 안전 지침을 따르십시오. • • • • • 안전 작동 수칙 다음 지침은 ANSI B71.4-2012에서 발췌한 내용입니다. • 교육 훈련 • • • • • 사용 설명서와 그 밖의 교육 자료를 읽으십시오. 운 전자나 정비사가 영어를 모를 경우 장비 소유자가 이 자료의 내용을 그들에게 설명해 주어야 합니다. 장비 안전 운전, 운전자 제어 장치 및 안전 표시를 잘 알아 두십시오. 모든 운전자 및 정비사는 교육을 받아야 하며, 소유 자는 사용자를 교육할 책임이 있습니다. 아이들이나 교육받지 않은 사람이 장비를 운전하거 나 정비하는 것은 절대로 허용하지 마십시오. 현지 규정에 의해 운전자의 나이가 제한될 수 있습니다.
– 후진하기 전에 후방을 살펴 장비 뒤에 아무도 없는지 확인하십시오. • – 도로에 다가가거나 도로를 건널 때 차를 조심하 십시오. 항상 다른 차량에 양보하십시오. • 장비가 작동 중일 때에는 노즐 개구부에서 멀리 떨 어지십시오. 구경하는 사람들이 전부 노즐 개구부 에서 떨어지게 하고 구경하는 사람들 방향으로 배 출하지 마십시오. • • 음주나 약물 복용 후에는 장비를 운전하지 마십 시오. • 번개는 중상 또는 사망을 유발할 수 있습니다. 번개 가 보이거나 천둥 소리가 들릴 경우 장비를 작동 하지 말고 피난처를 찾으십시오. • 견인 차량 엔진이 갑자기 멈추거나 장비가 앞으로 진행할 수 없어 경사로를 다 오를 수 없을 때는 장비 의 방향을 바꾸지 마십시오. 경사로에서는 항상 견 인 차량을 천천히 똑바로 후진하여 내려오십시오. 다칠 수 있는 위험한 행동은 하지 마십시오! 작업 영 역이나 그 주변에 사람이나 애완동물이 갑자기 나 타나면, 작업을 멈추십시오.
• • 불똥이나 화염이 없는 통풍이 잘 되는 개방된 곳에 서 배터리를 충전하십시오. 충전기를 배터리에 연 결하거나 연결 해제하기 전에 플러그를 뽑으십시 오. 보호복을 입고 절연된 도구를 사용하십시오. 견인 • 트레일러나 트럭에 장비를 싣거나 내릴 때에는 주의하십시오. 모든 부품을 양호한 작동 상태로 유지하고 모든 기 계 부품를 단단히 조여 두십시오. 닳거나 손상된 전 사지는 모두 교체하십시오. • 트레일러나 트럭에 장비를 싣는 경우 전폭 램프 를 사용하십시오. • 끈, 체인, 케이블, 로프 등을 사용하여 장비를 단단 히 묶으십시오. 전방 끈과 후방 끈은 모두 아래 방 향 및 장비에서 바깥 방향이 되어야 합니다. • Toro에서 승인한 부속 장치만 사용하십시오. 승인 되지 않은 부속장치와 함께 사용하면 제품 보증이 무효가 될 수 있습니다. 안전 및 교육용 전사지 안전 문구 데칼과 지침은 운전자가 쉽게 볼 수 있어야 하며, 위험이 발생할 가능성이 있는 구역 에 배치되어야 합니다.
설정 부품 확인 아래 차트를 사용하여 모든 부품이 선적되었는지 확인하십시오. 절차 설명 1 수량 바셀린(별매품) A/R 데브리 블로어 어셈블리 히치 볼트(3/8 x 3인치) 플랜지 너트(3/8인치) 히치 클레비스 볼트(5/8 x 4-1/2") 록 너트(5/8") 히치 핀 클레비스 휴대용 리모컨 AAA 배터리 나사, 소형 2 3 4 1 1 2 2 1 2 2 1 1 1 4 6 사용 배터리를 연결합니다 히치를 데브리 블로어에 장착하십시오 블로어를 견인 차량에 연결합니다 휴대용 리모컨을 조립합니다. 매체 및 추가 부품 설명 수량 사용 부품 카탈로그 사용 설명서 1 1 사용하기 전에 읽으십시오. 엔진 사용 설명서 1 엔진 작동 및 유지관리 항목을 참조하는데 사용하십시오. 사용자 교육용 자료 1 장비를 운전하기 전에 시청하십시오. 원격 제어 1 블로어를 원격으로 작동하는 데 사용하십시오. 적합성 인증서 1 CE 준수 여부를 확인하십시오.
위험 배터리 전해액에는 치명적인 독극물이자 심 각한 화상을 입힐 수 있는 황산이 포함되어 있습니다. • 전해액을 마시거나 피부, 눈 또는 옷에 닿 지 않도록 하십시오. 보안경과 고무 재질의 장갑을 착용하여 눈과 손을 보호하십시오. • 배터리는 피부를 씻을 수 있는 깨끗한 물 이 항상 있는 곳에서 충전하십시오. 양극 케이블(빨강색 케이블)을 양극(+) 단자에 연결하십시오. 2. 그림4 프레임 브래킷 히치 튜브 1. 2. 경고 캘리포니아 Proposition 65 경 고 3 데브리 블로어를 견인 차량에 연 결하기 음극 케이블(검정색 케이블)을 배터리의 음극 (-) 단자에 연결하십시오. 4. 부식이 생기지 않도록 단자와 장착 파스너를 바 셀린으로 코팅하십시오. 5. 배터리 커버를 설치하고 클립으로 고정하십시오. 3.
히치 핀과 클레비스를 사용하여 블로어 클레비 스 히치를 견인 차량에 연결합니다(그림5). 4. 그림6 1. 2. 3. 그림5 히치 핀 견인 차량 히치 1. 2. 3. 클레비스 4 휴대용 리모컨 조립 이 절차를 수행하는 데 필요한 부품: 1 휴대용 리모컨 4 AAA 배터리 6 나사, 소형 절차 1. 반쪽 리모컨을 함께 고정하는 고무 밴드를 분리 하고, 뒤쪽 커버를 분리합니다. 2. 각 배터리를 극성을 올바르게 맞추어 단자 크래 들에 끼웁니다(그림6). 참고:배터리를 잘못 설치하면, 장치가 손상되지 는 않지만 작동이 되지 않습니다. 크래들에는 각 단자에 맞는 극성 표시가 새겨져 있습니다. 9 나사 덮개 씰 4. 5. 6. 금속 개스킷 배터리 휴대용 리모컨 3. 금속 개스킷과 고무 씰이 리모컨의 채널 내에 들 어 있고, 뒤쪽 커버가 제자리에 설치되어 있는지 확인하십시오(그림6). 4. 커버를 6개의 나사로 고정하고(그림6) 1.5 ~ 1.
제품 개요 초크 제어 엔진을 냉간 시동하려면, 초크 제어 레버(그림8)를 켜 짐 위치로 옮깁니다. 제어장치 엔진 정지 엔진 정지 버튼을 눌러 엔진을 정지합니다 (그림7). 그림8 1. 2. 그림7 1. LED 표시등 2. 왼쪽으로 회전 3. 엔진 속도 감속 4. 엔진 시동 5. 6. 7. 오른쪽으로 회전 엔진 속도 가속 엔진 정지 초크 제어 아워 미터 3. 시동 스위치 아워 미터 아워 미터(그림8)는 장비의 총 작동 시간을 표시합니다. 엔진 시동 진단 표시등 시동 시퀀스를 완료한 후, 엔진 시동 버튼을 눌러 엔진 을 시동합니다(그림7). 시동 시퀀스는 엔진 시동 (페 이지 13)를 참조하십시오. 진단 표시등(그림9)은 아워 미터 밑에 있으며 장비 고 장 코드를 표시합니다. 키를 작동 위치로 돌리면 진단 표시등이 켜져 5초 동안 유지된 다음 5초 동안 꺼졌다 가 휴대용 리모컨의 버튼을 누를 때까지 1초에 3번씩 깜박이기 시작합니다.
운영 위험 특정 환경에서 휘발유는 가연성이 극히 높으며 쉽 게 폭발할 수 있습니다. 휘발유로 인한 화재나 폭 발은 자신과 타인에게 화상을 입힐 수 있으며 재산 상의 피해를 초래할 수도 있습니다. 참고:정상 운전 위치에서 장비의 좌측과 우측을 확 인하십시오. 연료 추가 • 연 료 탱 크 용 량 : 18.9L • 권장 연료: – 최상의 결과를 얻으려면 깨끗하고 오래되지 않 은(30일 이내), 옥탄가가 87 이상((R+M)/2 평가 방식)인 무연 가솔린만 사용하십시오. – 에탄올: 부피를 기준으로 최대 10% 에탄올(휘 발유) 또는 15% MTBE(메틸 t-부틸 에테르)를 함 유한 가솔린만 허용됩니다. 에탄올과 MTBE는 동일한 물질이 아닙니다. 부피 기준으로 15% 에탄올(E15)이 포함된 가솔린은 사용하도록 승인되지 않았습니다.
경고 3. 휘발유를 삼키면 인체에 유해하거나 치명적일 수 있습니다. 증기에 장기간 노출되면 심각한 부상이 나 질병을 초래할 수 있습니다. • 증기를 장시간 흡입하지 마십시오. • 노즐 및 연료 탱크나 컨디셔너 입구에서 얼굴 을 멀리 하십시오. • 가솔린이 눈과 피부에 닿지 않게 하십시오. 참고:탱크의 이 공간은 휘발유가 팽창하는 데 필 요합니다. 연료 탱크를 완전히 가득 채우지 마 십시오. 4. 연료 탱크 캡을 단단히 설치하십시오. 5. 흘린 휘발유가 있으면 모두 닦아 내십시오. 엔진 오일량 점검 컨디 셔 너 사 용 안정제/컨 엔진을 시동하여 장비를 사용하기 전에, 엔진 크랭크 케이스의 오일량을 확인하십시오. 엔진 오일 수준 점 검 (페이지 19)를 참조하십시오. 장비에서 연료 안정제/컨디셔너를 사용하면 다음 과 같은 장점이 있습니다. 가솔린을 90일 이내 기간 동안 보관하면 신선한 상 태가 유지됩니다. 보다 오래 보관하려면 연료 탱크 를 비워야 합니다.
엔진 시동 및 정지 엔진 시동 경고 회전하는 부품으로 인해 사람이 심하게 다칠 수 있습니다. • 작동 중인 장비 근처에 손이나 발이 놓이지 않 게 하십시오. • 움직이는 부품 주변에 손, 발, 머리칼 및 옷이 닿 지 않게 하여 부상을 방지하십시오. • 덮개, 쉬라우드 또는 가드를 분리한 상태에서는 절대로 장비를 작동하지 마십시오. 1. 블로어는 견인 차량을 시동하기 전에 견인 차 량에 연결해야 합니다. 2. 냉간 시동 전에 초크 제어 장치를 ON 위치로 옮 기십시오. 그 림 13 1. LED 표시등 2. 왼쪽으로 회전 3. 엔진 속도 감속 4. 엔진 시동 오른쪽으로 회전 엔진 속도 가속 엔진 정지 참고:각 버튼을 누르는 간격은 최대 3초입니다. 버튼을 누른 후 그 다음 버튼을 3초 이내에 누르 지 않으면 버튼 누름 시퀀스가 취소되므로 처음 부터 다시 시작해야 합니다. 참고:식지 않은 엔진이나 뜨거운 엔진은 초크를 작동할 필요가 없습니다.
노즐 방향 조정 엔진 정지 1. 엔진 속도를 3/4 스로틀로 낮춥니다. 2. 리모컨의 멈춤 버튼을 누릅니다. 3. 장비에서 떠나는 경우, 키를 OFF 위치로 돌리고 엔진에서 뺍니다(그림12). 노즐 개구부 방향은 리모컨의 해당 버튼을 눌러 오른 쪽에서 왼쪽으로 변경할 수 있습니다(그림15). 시동, 정지 및 무작동 시간 종료 아무 버튼이나 누르면 리모컨이 작동합니다(켜집니 다). 배터리 전력을 아낄 수 있도록 리모컨은 약 3초 동 안 활성 상태를 유지하다가 3초 이내에 버튼 사용이 없 으면 자동으로 꺼집니다. 장치가 시간 종료되어 전력 이 꺼지면, 모든 리모컨 LED 작동이 멈춥니다(그림14). 아무 버튼이나 누르면 리모컨이 다시 작동합니다. 그 림 15 1. LED 표시등 2. 왼쪽으로 회전 3. 엔진 속도 감속 4. 엔진 시동 5. 6. 7. 오른쪽으로 회전 엔진 속도 가속 엔진 정지 작동 요령 경고 그 림 14 1. LED 표시등 2. 왼쪽으로 회전 3. 엔진 속도 감속 4.
• 견인 차량에 연결되지 않은 상태로 데브리 블로어 를 작동하지 마십시오. • 블로어를 작동하는 연습을 하십시오. 깨끗하게 정 리한 곳으로 물질이 다시 날려 오는 일이 없게 하려 면, 바람이 부는 방향으로 날리는 것이 좋습니다. • 블로어 노즐 방향에 주의하고, 사람을 겨냥하지 마십시오. • 사각 지대, 관목, 나무 또는 그 외의 시야를 방해하 는 물체에 접근할 때에는 주의하십시오. • 갑자기 방향을 바꾸거나 경사로에서 방향을 바꿀 때는 속도를 줄이십시오. • 후진하기 전에 후방을 살펴 장비 뒤에 아무도 없는 지 확인하십시오. • 적절하게 환기되지 않는 막힌 장소 내에서 또는 그 런 장소를 블로어 노즐로 겨냥한 상태로 엔진을 구 동하지 마십시오. 배기 가스는 위험하며, 생명을 앗 아갈 가능성도 있습니다. • 작업 중에는 엔진을 최대 스로틀로 구동하십시오. • 데브리 밑으로 바람이 향하도록 블로어 개구부 를 조정하십시오.
유지보수 권장 유지보수 일정 유지보수 서비스 간격 유지보수 절차 처음 8시간 후 • 벨트의 상태와 장력을 점검합니다. 처음 10시간 후 • 휠 러그 너트의 토크를 점검합니다. 매번 사용하기 전 또는 매일 • 엔진 오일량 확인. • 엔진 스크린과 오일 쿨러를 청소합니다. • 노즐 클램프와 노즐 가이드를 점검합니다. 매 25시간 • 폼 공기 필터 엘리먼트를 청소하고 종이 엘리먼트 손상 여부를 점검하십시오 (먼지 나 모래가 많은 환경에서는 좀 더 자주 시행). 매 50시간 • 벨트의 상태와 장력을 점검합니다. 매 100시간 • 종이 공기 필터 엘리먼트를 교체하십시오 (먼지나 모래가 많은 환경에서는 좀 더 자주 시행). • 엔진 오일을 교환합니다. 매 200시간 • 카본 캐니스터 공기 필터를 교체합니다(먼지나 모래가 극단적으로 많은 환경에 서는 좀 더 자주 시행). • 카본 캐니스터 정화 라인 필터를 교체합니다. • 오일 필터를 교환합니다. • 스파크 플러그를 점검합니다.
일일 유지보수 점검 목록 이 페이지를 복사하여 사용하십시오. 유지보수 점검 항목 요일: 월 화 수 목 금 계기 작동 상태 점검 연료량 확인. 엔진 오일량 확인. 엔진 냉각휜 청소. 공기 필터 프리클리너 점검. 엔진 소음 이상 점검. 오일 누출 여부 점검. 타이어 압력 점검. 노즐 장착 클램프 토크 점검 벗겨진 페인트 복원.
에어 클리너 정비 2. 서비스 간격: 매 25시간—폼 공기 필터 엘리먼트를 청 소하고 종이 엘리먼트 손상 여부를 점검하십시오 (먼지나 모래가 많은 환경에서는 좀 더 자주 시행). 참고:필터의 밀봉된 끝 부분을 점검합니다. 중요: 손상된 필터는 설치하지 마십시오. 3. 매 100시간—종이 공기 필터 엘리먼트를 교체 하십시오 (먼지나 모래가 많은 환경에서는 좀 더 자주 시행). 새 공기 필터를 설치합니다. 공기 필터 설치 (페 이지 18)를 참조하십시오. 공기 필터 설치 공기 필터 점검 1. 새 필터가 운송 중에 손상되지 않았는지 점검 합니다. 중요: 엔진이 손상되지 않도록, 항상 에어 클리너 어셈블 리가 완벽하게 설치된 상태에서 엔진을 작동하십시오. 에어 클리너 몸체가 손상되면 공기가 샐 수 있으 니 이를 점검하십시오. 덮개가 에어 클리너 몸체 주위를 밀봉하는지 확인하십시오(그림16). 중요: 손상된 엘리먼트는 사용하지 마십시오.
2 1 g018506 그 림 18 그 림 17 1. 3. 카본 캐니스터 2. 1. 카본 캐니스터 공기 필터 새 공기 필터를 설치합니다. 카본 캐니스터 정화 라인 필터 교환 서 비 스 간 격 : 매 200시간 참고:가끔 정화 라인 필터에 이물질이 있는지 점검합 니다. 필터에 이물질이 있으면, 교체하십시오. 1. 엔진을 멈추고 키를 뺀 다음, 움직이는 모든 부 품이 멈출 때까지 기다린 다음 작업 위치를 떠 나십시오. 2. 카본 캐니스터 정화 라인 필터의 양쪽 측면의 스 프링형 호스 클램프를 움직여 필터에 닿지 않 게 합니다(그림18). 카본 캐니스터 정화 라인 필터 2. 체크 밸브 3. 카본 필터를 분리하여 폐기합니다(그림18). 4. 필터에 표시된 화살표가 체크 밸브 방향이 되도 록 새 필터를 호스에 설치하고 호스 클램프로 고정하십시오(그림18). 엔진 오일 정비 참고:작동 조건이 먼지나 모래가 극단적으로 많은 경 우 오일을 더 자주 교환하십시오.
참고:배출 밸브에 호스를 삽입하여 오일 흐름 을 유도할 수 있습니다. 호스는 장비에 포함되 어 있지 않습니다. 참고:엔진 오일을 점검하기에 가장 좋은 시간은 일과 시작 전 엔진이 식어 있을 때입니다. 엔진이 이미 작동 되었다면 점검하기 최소 10분 전에 오일이 기름통으로 다시 빠져나가도록 하십시오. 오일 레벨이 계량봉의 ADD 표시에 있거나 그 밑에 있다면 FULL 표시까지 오 일을 보충하십시오. 오일을 과도하게 보충하지 마십시 오. 오일 레벨이 FULL 표시와 ADD 표시 사이에 있으 면 오일을 보충할 필요가 없습니다. 1. 평평한 곳에 장비를 주차합니다. 2. 엔진을 멈추고 키를 뺀 다음, 움직이는 모든 부 품이 멈출 때까지 기다린 다음 작업 위치를 떠 나십시오. 3. 오일 딥스틱 주위를 깨끗히 청소하여(그림20) 이 물질이 주입구 구멍으로 떨어져 엔진을 손상시 키는 일이 없게 하십시오. 5. 오일이 완전히 배출되면, 배출 밸브를 닫습니다. 참고:사용한 오일은 재활용 센터에서 폐기합 니다.
3. 교환 필터의 고무 개스킷에 새 오일을 얇게 바릅 니다(그림22). 4. 교환할 오일 필터를 필터 어댑터에 설치하고, 고 무 개스킷이 필터 어댑터에 닿을 때까지 오일 필 터를 시계 방향으로 돌린 다음 필터를 2/3 ~ 1바 퀴 더 돌려 조입니다(그림22). 5. 적절한 종류의 새 오일을 크랭크케이스에 가득 채웁니다. 엔진 오일 정비 (페이지 19)를 참조 하십시오. 6. 약 3분 동안 엔진을 작동한 후 엔진을 멈춘 다음, 오일 필터 주위에 오일이 새는지 점검합니다. 7. 엔진 오일량을 확인하고 필요한 경우 오일을 보 충합니다. 그 림 23 1. LED 표시등 2. 왼쪽으로 회전 3. 엔진 속도 감속 4. 엔진 시동 리모컨과 베이스 유닛 연결하기 중요: 연결 과정을 진행하기 전에 반드시 전체 진행 절차를 읽으십시오. 스파크 플러그를 설치하기 전에 가운데와 측면 전극 사이의 공극이 정확한지 확인하십시오.
스파크 플러그 설치 1. 스파크 플러그와 금속 와셔를 설치합니다. 에어 갭이 올바르게 설치되어 있는지 확인합니다. 2. 스파크 플러그를 24.4~29.8N·m(18~22ft-lb)로 조 입니다. 3. 스파크 플러그에 선을 연결합니다(그림24). 연료 필터 교환 서 비 스 간 격 : 매 500시간 그 림 24 1. 중앙 전극 절연체 2. 측면 전극 3. 이물질이 낀 필터는 연료 라인에서 분리한 후 절대로 다시 설치하지 마십시오. 공극(그림은 치수와 비례 하지 않음) 중요: 검정색으로 코팅이 되었거나 전극이 마모 되었거나 기름막이 덮여 있거나 균열이 있는 스파 크 플러그는 항상 교체하십시오. 2. 1. 엔진을 멈추고 키를 뺀 다음, 움직이는 모든 부 품이 멈출 때까지 기다린 다음 작업 위치를 떠 나십시오. 2. 장비의 열이 식게 둡니다. 3. 호스 클램프의 양쪽 끝을 함께 비튼 다음 밀어서 필터에서 분리합니다(그림26).
연료 탱크 정비 노즐 점검 서비스 간격: 매번 사용하기 전 또는 매일 위험 특정 환경에서 휘발유는 가연성이 극히 높으며 쉽 게 폭발할 수 있습니다. 휘발유로 인한 화재나 폭 발은 자신과 타인에게 화상을 입힐 수 있으며 재산 상의 피해를 초래할 수도 있습니다. • 엔진이 식으면 연료 탱크에서 휘발유를 배출 합니다. 이 작업은 막히지 않은 공간의 실외에 서 하십시오. 흘린 휘발유가 있으면 모두 닦 아 내십시오. • 휘발유를 배출할 때 절대 담배를 피워서는 안 되며, 노출된 화염이 있는 곳이나 불꽃으로 인 해 휘발유 가스에 불이 붙을 수 있는 곳에서 멀 리 떨어지십시오. 1. 평평한 곳에 장비를 주차하고 연료 탱크가 완전 히 배출되었는지 확인합니다. 2. 엔진을 멈추고 키를 뺀 다음, 움직이는 모든 부 품이 멈출 때까지 기다린 다음 작업 위치를 떠 나십시오. 3. 연료 필터의 호스 클램프를 느슨하게 푼 다음 연 료 라인을 따라 위로 밀어서 연료 필터에서 분 리합니다(그림26). 4.
참고:가능한 경우, 덮개와 배터리를 분리할 때 고무 씰과 금속 개스킷은 채널 안에 그대로 두 십시오. 노즐 방향을 바꿀 때 벨트가 미끄러지면, 벨트를 조 정해야 합니다. 1. 풀리 마운팅 브래킷을 블로어 프레임에 고정하 는 볼트를 느슨하게 풉니다(그림30). 2. 토크 렌치를 풀리 마운팅 브래킷 안에 넣습니 다(그림30). 3. 토크 렌치 판독값이 22.6~26.0N·m (200~230in-lb) 이 될 때까지 노즐 밖으로 풀리 마우팅 브래킷을 돌립니다(그림30). 4. 장착 볼트를 조입니다. 1 2 그 림 31 1. 2. 3. 3 1 5 나사 덮개 씰 4. 5. 6. 금속 개스킷 배터리 휴대용 리모컨 2. 방전된 배터리는 분리하여 현지 규정에 따라 적절하게 폐기합니다. 3. 새 배터리를 각각 극성을 올바르게 맞추어 단 자 크래들에 꽂습니다. 4 참고:배터리를 잘못 설치하면, 장치가 손상되지 는 않지만 작동이 되지 않습니다. 4.
4. 크랭크케이스 오일을 교환합니다. 엔진 오일 정 비 (페이지 19)를 참조하십시오. 5. 타이어 압력을 점검합니다. 타이어 압력 점검 (페 이지 12)를 참조하십시오. 6. 30일 이상 사용하지 않는 경우 장비를 보관할 준 비를 합니다. 다음과 같이 장비를 보관할 준비 를 하십시오. A. 참고:연료 안정제/컨디셔너는 신선한 가 솔린과 혼합하여 사용해야 가장 효과가 있 습니다. G030098 그 림 32 1. 석유계 안정제/컨디셔너를 탱크의 연료에 추가하십시오. 안정제 제조사의 혼합 지침 을 따르십시오. 메탄올이나 에탄올이 함유 된 연료 첨가제는 사용하지 마십시오. 휴즈 수신기 수신기 와이어 하니스에는 퓨즈 블록이 포함되어 있습 니다. 퓨즈 블록은 컨트롤 타워 오른쪽의 수신기 뒤 에 있습니다(그림33). B. 5분간 엔진을 작동하여 조정제를 첨가한 연료가 연료 장치를 통해 엔진에 고르게 퍼 지도록 합니다. C. 엔진을 멈추고 식힌 다음, 연료 탱크를 비 웁니다.
폐기물 처분 엔진 오일, 엔진 및 리모컨 배터리는 환경 오염 물질 입니다. 이런 물질은 주 정부와 지방 정부의 법규에 따라 폐기하십시오.
문제해결 고장 코드 점검 진단 표시등에 시스템 고장이 있는 것으로 표시되면( 진단 표시등 (페이지 10) 참조), 고장 코드를 확인하여 장 비에 무슨 문제가 있는지 판단하십시오. 진단 모드로 들어가 코드 확인하기 1. 키를 OFF 위치로 돌리면 전원이 꺼집니다. 2. 끈이 달린 캡을 당겨서 2개의 진단 션트 커넥터(그림34)에서 분리합니다. 3. 진단 션트 커넥터를 함께 연결합니다(그림34, B). 그 림 34 4. 키를 작동 위치로 돌려 전원을 켭니다. 5. 깜박거리는 횟수를 세어서 고장 코드를 판단한 후, 다음 표를 참조하십시오. 참고:다수의 고장이 있는 경우, 두 고장이 깜박거린 다음 길게 멈춘 후 깜박거림 시퀀스를 반복합니다.
코드 LED 깜박거림 패턴 의미 상세 정보 장비 관련 고장 11 한 번 깜박거림, 멈춤, 한 번 깜 박거림, 길게 멈춤, 전체 반복 BASE와 통신이 안 됨 꽂히지 않은 커넥터나 헐겁거 나 연결되지 않은 하니스 커넥 터를 찾아서 연결하십시오. 배선에 문제가 있습니다. Toro 판매 대리점에 문의하십시오. 베이스가 불량입니다. Toro 판 매 대리점에 문의하십시오. 12 한 번 깜박거림, 멈춤, 두 번 깜 박거림, 길게 멈춤, 전체 반복 베이스 및/또는 HH와 버전이 호환되지 않음 잘못된 소프트웨어입니다 (TORODIAG에서 올바른 소프 트웨어를 설치해야 함), Toro 판 매 대리점에 문의하십시오. 13 한 번 깜박거림, 멈춤, 세 번 깜 박거림, 길게 멈춤, 전체 반복 잘못된 HH입니다. RevA에 구 현되어 있지 않습니다. 잘못된 제품 연결(예: ProPass 휴대용 기기로 MH–400에서 소 프트웨어 업데이트를 시도) 14 오일 압력이 낮아서 ETR가 떨 어졌습니다.
참고: 29
참고: 30
해외 판매사 목록 판매사: Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation 국가: 헝가리 홍콩 한국 전화 번호: 36 27 539 640 852 2155 2163 82 32 551 2076 판매사: Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s. 국가: 콜롬비아 일본 체코 공화국 Casco Sales Company 푸에르토리코 787 788 8383 Mountfield a.s. 슬로바키아 Ceres S.A. 코스타리카 506 239 1138 Munditol S.A. 아르헨티나 CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co.
Toro 일 반 상 용 제 품 보 증 2년 유한 제품 보증 적용 조건 및 제품 The Toro Company와 그 계열사인 Toro Warranty Company는 서로 간 의 협정에 따라 공동으로 귀하의 Toro 상용 제품("제품")에 원자재 또는 제조 기술상의 결함이 없음을 2년간, 또는 작동 시간* 기준으로 1,500 시간 동안(둘 중 먼저 발생하는 쪽 적용) 보증합니다. 본 보증은 에어 레이터(Aerators)를 제외한 모든 제품에 적용됩니다(에어레이터에 대 해서는 별도의 보증서를 참고하십시오). 당사에서는 보증 가능한 조 건이 충족되면 진단, 작업, 부품 및 운송에 드는 비용을 포함해 어떠 한 비용도 귀하께 청구하지 않고 해당 제품을 수리해 드릴 것입니다. 본 보증은 제품이 원래의 구매자에게 인도된 날로부터 시작됩니다. * 시간 측정기가 장착된 제품 보증 서비스를 받는 방법 • • 정상적인 소음, 진동, 마모 및 노후화.