FORM NO. 01-502-1390 OPERATOR'S 7 MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone wise using or maintaining this machine are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page Page SAFETY INSTRUCTIONS OPERATING CHARACTERISTICS . SAFETY AND INSTRUCTION DECALS 4-5 LUBRICATION SPECIFICATIONS .6 MAINTENANCE SET UP INSTRUCTIONS .. .B-7 STORAGE .. BEFORE OPERATING .8-9 IDENTIFICATION AND ORDERING OPERATING INSTRUCTIONS 9 PROPRIETORSHIP SAFETY INSTRUCTIONS The safety alert symbol means CAUTION, WARNING or DANGER "personal safety instruction”. Read and understand the instruction because it has to do with safety.
SAFETY INSTRUCTIONS (Continued) 9. If cutting blades strike a solid object or the machine vibrates abnormally, disengage PTQ, move throttle to SLOW, set parking brake and shut engine off. Remove key from switch to prevent possibility of accidental starting. Check cutting unit and traction unit for damage and malfunctioning parts. Repair any damage before restarting the engine and operating the Flail 2760. Be sure cutting blades are in good condition and blade bolts are torqued to proper specifications. 10.
SAFETY AND INSTRUCTION DECALS (Continued) rotating SEWERS CAN CAUSE PERSONAL INJURY. a5 DONOR OPERATE UNLESSSHIELDISINPLACE. REAR SIDE OF HOUSING {Part No. 01-506-0130) A DANGER J PULLEY LU R SRR R OUS INJURY, GUARDS ARE N PLACE ON BELT GUARD {Part No. 01-806-0040) FRONT SIDE OF HOUSING (Part No. 01-506-0340) NEAR BEARINGS & GREASE POINTS {Part No.
SPECIFICATIONS 144 Knives Rotor Speedup RPM Rotor 3/16" wall (10cm x .47 cm wall) Rotor Overbearing" (3.8 cm) ROTOR: CASTORS: Swivel castors Gearbox 50 HP Drive Belt 2 3V Section Belts DRIVE: CUTTING HEIGHT: cm) in 1/2" {incrementalists REAR ROLLER: cmy O.D. BEARINGS: 3 self sealed and self aligning DIMENSIONS: Cutting Width: 60" Overall Width: 69.5" Weight: 480 Ibs. SET UP INSTRUCTIONS ATTACH FLAIL TO 300 SERIES GROUNDSMASTER® (Flg.
SET UP INSTRUCTIONS (Continued) 11. Have a helper push down the left push arm; then remove the 2 x 4" blocks of wood. 14, Tighten the setscrews on both bearings. 12, Have a helper push down the right push arm; then remove the 2" x 4" blocks of wood. 13, Attach the Left Hand Chain (15 links) to the Center Arm as shown in Fig. 1. Secure shackle bolts. 14. Attach the Right Hand Chain (4 links) to the Center Arm. Secure shackle bolts. 15. Practice raising and lowering the FLAIL.
BEFORE OPERATING INSPECT BLADES A CAUTION Sharp edges of mower blades can cut you. ALWAYS wear gloves for any type of blade maintenance or adjustment. 1. Follow these instructions before operating: Always inspect all the blades before using the Flail. Make sure all the bolts are tight and torqued 18 21st. Lbs. Operating the Flail with missing or damaged cutter blades can cause severe vibration and damage to other components. Sharpen or replace any damaged blades.
OPERATING INSTRUCTIONS INTERLOCK SWITCHES The Grounds master has interlock switches in the electrical system. These switches are designed to stop the engine when operator gets off the seat while either the PTO lever is engaged or traction pedal Is depressed. However, the operator may get off the seat while engine is running. Although engine will continue to run if PTO lever is disengaged and traction pedal is released, iris strongly recommended that the engine be stopped before dismounting from the seat. 1.
LUBRICATION BEARINGS (Fig. 6) The FLAIL has three self sealing bearings that must be lubricated with a No. 2 Lithium based grease. IMPORTANT: Lubricate the bearings as often as necessary to maintain a slight leakage on the seals. Too much grease can cause overheating. WHEELS (Flg. §) Under normal conditions, grease the wheels and the wheel pivot tubes every 50 hours of use. Use a No. 2 Lithium based grease. PTO (Fig. 6) 1. Grease the PTO fittings weekly or Avery 40 operating hours. Use aNo.
MAINTENANCE BLADE MAINTENANCE A\ CAUTION Sharp edges of mower blades can cut you. ALWAYS wear glaces for any type of blade maintenance or adjustment. INSPECT BLADES ALWAYS inspect the condition of the blades before every use. Inspect the shackles and blades to be sure they are in good operating condition. Sharpen or replace any damaged blades. Always replace the cutter blades in sets to avoid excessive and damaging vibration ot the rotor.
MAINTENANCE (Continued) 20. Slowly move the Grounds master forward and sower the Fail 2760 until the holes on the skid shoes line up with the holes on the side of the main frame. Tums off engine and remove the key. 21, Replace all six bolts attaching the Skid Shoes to the mainframe and secure. 22. Replace the bat. 23. Using the adjustment nut on the spring rod, set the tension of the bat. 24, Replace the Belt Guard and secure. ADJUSTING BELT DRIVE (Fig.
STORAGE 1. Thoroughly clean the FLAIL 2760. The housing should be free of dirt, leaves and debris. 2. Lubricate all grease fittings. Wipe off any excess lubricant. 3. Place a light coat of grease on the splines of the PTO adapter. 4. Tighten all fasteners. 5. Check the condition of the cutter blades. Replace any damaged blades. Tighten all fasteners. Refer to the Maintenance section of this Operators Manual for specifications. 8. Check the tension and the condition of the drive belt. Replace if worn. 7.
I The Toto Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The following time periods from the date of purchase apply: Commercial Products ..