Installation Instructions

ManualsBrandsToro ManualsAttachmentsLight Kit, GreensPro 1200 Greens Roller

FormNo.3376-366RevA

LightKit

GreensPro™1200GreensRoller

ModelNo.44909

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

LEDlight2

Lightmountingbracket2

Hex-headbolt(M6x20mm)

Locknut(M6)

Washer(1/4x7/8inch)

Washer(M6x20mm)

InstalltheLEDlight.

Lightswitch2Installthelightswitch.

Cableties

Wiringharness1

Installtheleadsandwiringloom.

InstallingtheLEDLight

1.Alignthelightmountingbracketwiththeholesfound

ontheleftsideoftheseatpanange(Figure1).

G020974

Figure1

1.Locknut(5/16inch)5.Washer(1/4x7/8inch)

2.Lightmountingbracket

6.Washer(M6x20mm)

3.LEDlight

7.Locknut(M6)

4.Hex-headbolt(M6x20

mm)

2.AlignthebottomoftheLEDlightontheleftsidewith

theholeonthelightmountingbracket(Figure1).

3.PlacethebottomoftheLEDlightontheleftsideinto

thehole,andsecureittothemountingbracketby

tighteningthelocknut(5/16inch)asshowninFigure1.

4.Insertthehex-headbolt(M6x20mm)intothewasher

(1/4x7/8inch)asshowninFigure1.

5.Insertthehex-headbolt(M6x20mm)andthewasher

(1/4x7/8inch)intothelightmountingbracket

(

Figure1).

6.Placethewasher(M6x20mm)ontothebottomofthe

hex-headbolt(M6x20mm)andtightenitwiththe

locknut(M6)asshowninFigure1.

7.Repeatsteps1through6toinstalltherightLEDlight

kit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3376-366*A

Summary of content (4 pages)

PAGE 1
Form No. 3376-366 Rev A Light Kit GreensPro™ 1200 Greens Roller Model No. 44909 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. LED light Light mounting bracket Hex-head bolt (M6 x 20 mm) Locknut (M6) Washer (1/4 x 7/8 inch) Washer (M6 x 20 mm) 2 2 2 2 2 2 Install the LED light. Light switch 2 Install the light switch. Cable ties Wiring harness 7 1 Install the leads and wiring loom. Installing the LED Light 1.
PAGE 2
Installing the Light Switch 4. Fasten the wiring loom to the seat-pan flange using the cable ties (Figure 4). 1. Align the light switch with the opening found on the left side of the seat pan flange (Figure 2). 1 G020975 Figure 2 1. Light switch 1 2 G020994 Figure 4 2. Insert the light switch into the opening found on the left side of the seat pan flange (Figure 2). 1. Cable tie (7) Installing the Leads and Wiring Loom 2. Wiring loom 5.
PAGE 3
Notes: 3
PAGE 4