Installation Instructions

ManualsBrandsToro ManualsAttachmentsWireless Hour Meter Kit, 2014 and Before GreensPro 1240 Greens Roller

FormNo.3380-722RevA

WirelessHourMeterKit

GreensPro

™

1240GreensRoller

ModelNo.44922

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Wiringharness1Installthewiringharness.

Hourmeter1

Regulator1

Screw(M6x20mm)

Locknut(M6)

Washer(M6x12mm)

Cabletie

Installtheregulatorandthehourmeter.

InstallingtheWiringHarness

1.Ensurethatthemachineisoffandtheengineiscool.

2.Disconnecttheexistinghour-meterwiringharness

fromthelighting-coilwiresandtheexistinghourmeter

(Figure1).

G025121

Figure1

1.Existinghour-meterwiring

harness

2.Lighting-coilwires

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3380-722*A

Summary of content (4 pages)

PAGE 1
Form No. 3380-722 Rev A Wireless Hour Meter Kit GreensPro™ 1240 Greens Roller Model No. 44922 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. Wiring harness 1 Install the wiring harness.
PAGE 2
3. If the machine is equipped with a light kit, disconnect the existing hour-meter wiring harness from the light-kit wiring harness (Figure 2). A 1 2 1 2 3 B G025126 Figure 2 1. Light-kit wiring harness 2. Existing hour-meter wiring harness 4. Remove the existing hour-meter wiring harness. 5. Remove the existing hour meter (Figure 3). Note: Retain the existing hour meter and hour-meter wiring harness for the option of installing them in the future. G025129 Figure 4 1. Bolt 1 3.
PAGE 3
Installing the Regulator and the Hour Meter 1 1. If necessary, unlatch the seat and tip it forward. 2. Insert 2 screws (M6 x 20 mm) with 2 washers (M6) down through the holes in the top of the seat pan (Figure 6). 2 1 2 G025123 Figure 5 1. Wireless-hour-meter wiring harness 2. Lighting-coil wires 9. If the machine is equipped with a light kit, plug the light-kit wiring harness into the appropriate connector of the wireless-hour-meter wiring harness (Figure 2). G025124 Figure 6 1.
PAGE 4
installing an M6 washer and an M6 locknut onto the appropriate M6 x 20 mm screw (Figure 7). 5. Secure the other side of the regulator by installing an M6 washer and an M6 locknut onto the other M6 x 20 mm screw (Figure 7). 1 6. Connect the plug on the regulator to the appropriate plug on the wireless-hour-meter wiring harness (Figure 8). 1 2 2 2 G025130 Figure 11 Regulator not shown 1. Push mount 2. Cable ties G025132 Figure 8 1. Regulator plug 10.