Installation Instructions

ManualsBrandsToro ManualsAttachmentsWireless Hour Meter Kit, Serial Number 315000001 and After GreensPro 1240 or 1260 Greens Roller

FormNo.3408-458RevA

WirelessHourMeterKit

SerialNumber315000001andUpGreensPro

™

1240or1260

GreensRoller

ModelNo.44927

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheexistinghourmeterandwiringharnessfroma

GreensPro1240greensroller.

Hourmeter1

Wiringharness(Model44912only)

Regulator1

Screw(6x20mm)

Locknut(6mm)

Washer(6mm)

Cabletie

InstallthekitonaGreensPro1240greensroller.

Hourmeter1

Wiringharness(discard)

Regulator1

Screw(6x20mm)

Locknut(6mm)

Washer(6mm)

Cabletie(asneeded)

InstallthekitonaGreensPro1260greensroller.

RemovingtheExistingHour

MeterandWiringHarness

fromaGreensPro1240Greens

Roller

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrakeandshutofftheengine.

3.Ensurethatthemachineisoffandtheengineiscool.

4.Removethepushmountfromtheseatpan(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3408-458*A

Summary of content (8 pages)

PAGE 1
Form No. 3408-458 Rev A Wireless Hour Meter Kit Serial Number 315000001 and Up GreensPro™ 1240 or 1260 Greens Roller Model No. 44927 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty.
PAGE 2
1 2 G025126 g025126 Figure 3 1. Light-kit wiring harness g028867 2. Existing hour-meter wiring harness 7. Disconnect the existing hour-meter wiring harness from the hour meter and remove the hour-meter wiring harness (Figure 4). Figure 1 1. Push mount 8. Press the spring tabs on both sides of the existing hour meter and remove it (Figure 4). 5. Disconnect the existing hour-meter wiring harness from the main wiring harness Figure 2).
PAGE 3
Installing the Regulator and the Hour Meter on a GreensPro 1240 Greens Roller 4. Align the grounding lead of the regulator over a mounting slot, and secure the lead and the regulator by installing an washer (6 mm) and a locknut (6 mm) onto the appropriate screw (6 x 20 mm); refer to Figure 6. 5. Secure the other side of the regulator by installing a washer (6 mm) and a locknut (6 mm) onto the other screw (6 x 20 mm); refer to Figure 6. 1. If necessary, unlatch the seat and tip it forward. 2.
PAGE 4
12. Use the cable ties to secure the wires to the seat-support strut and the front of the seat pan (Figure 11). 2 13. Lower and latch the seat. 1 Installing the Kit on a GreensPro 1260 Greens Roller G025127 Note: The wiring harness included in the kit is required only for the GreensPro 1240 greens roller. If you are installing the kit on a GreensPro 1260 greens roller, discard the harness. g025127 Figure 9 1. Hour meter 2. Seat pan 1. Park the machine on a level surface. 2.
PAGE 5
1 5 2 3 4 G025125 g025125 Figure 13 1. Screw 4. Locknut (6 mm) 2. Grounding lead 5. Regulator g189009 Figure 16 1. Wiring harness 3. Washer (6 mm) 2. Hour meter 12. Press the spring tabs on both sides of the existing hour meter and remove it. 7. Align the grounding lead of the regulator over a mounting slot, and secure the lead and the regulator by installing an washer (6 mm) and a locknut (6 mm) onto the appropriate screw (6 x 20 mm); refer to Figure 13. 13.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8