Installation Instructions

ManualsBrandsToro ManualsTop DressersSH/EH Twin Spinner, MH-400 Material Delivery Unit

FormNo.3389-489RevA

SH/EHTwinSpinner

MH-400MaterialDeliveryUnit

ModelNo.44944

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

119-6805

1.Cutting/dismembermenthazard,impeller—stayawayfrom

movingparts,keepallguardsandshieldsinplace.

119-6804

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

119-6810

1.ReadtheOperator'sManual.

2.Usetwopeoplerequiredtolift.

119-6858

1.Spinnerspeedpercentage

2.Beltspeedpercentage

119-6857

1.Lightspreadspinneradjustmentsettings(refertothe

Operationsectionformoreinformation).

3.Warning—slideadjustmentandtailgateadjustment.

2.Heavyspreadspinneradjustmentsettings(refertothe

Operationsectionformoreinformation).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3389-489*A

Summary of content (12 pages)

PAGE 1
Form No. 3389-489 Rev A SH/EH Twin Spinner MH-400 Material Delivery Unit Model No. 44944 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 119-6810 119-6805 1. Read the Operator's Manual. 1. Cutting/dismemberment hazard, impeller—stay away from moving parts, keep all guards and shields in place. 2.
PAGE 2
119-6859 119-6859 1. Spinner speed adjustment 119-6867 1. Fine tuning spinners 119-6865 1. Slide adjustment 119-6868 1. Slide adjustment 119-6866 1.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Qty. Hopper guard Bolt, 1/4 x 5/8 inch Flange nut, 1/4 inch Twin spinner Quick attach mounting clamps (supplied with the MH–400) 1 5 5 1 2 Use Install the hopper guard Install the twin spinner No parts required – Connect the hydraulic hoses No parts required – Set the desired spread pattern No parts required – Operate the Twin Spinner Decal, Part No.
PAGE 4
5. While supporting the twin spinner, slide the rear option attachment clamp assembly back into the slots in the brackets, and over the rear edge (Figure 2). 2 6. Ensure that the twin spinner is centered between the brackets. Then re-install the lock rings over the lock pins and push down on the clamp handles Installing the Twin Spinner Note: If the clamp assembly is too loose and the twin spinner slides within the clamps, turn the lock rings into the clamps a few turns until the twin spinner is secure.
PAGE 5
Connect the hydraulic hoses to the option control valve on the MH-400 as follows (Figure 3): 3 • Pull back (or push forward) on the outer sleeve of the female connector and insert the male connector. Connecting the Hydraulic Hoses • Hold the male connector firmly in place and release the outer sleeve of the female connector. • Ensure that the connectors are pushed all the way in and are securely locked in place.
PAGE 6
Adjusting the Spinner Valve 4 MH-400 SH models 1. Loosen the knob securing the spinner valve lever (Figure 6). Setting the Desired Spread Pattern No Parts Required Select the Desired Spread Pattern Figure 6 • A-Ultra Light Pattern 1. Spinner valve • B-Light to Heavy Spread Pattern 2. Rotate the spinner valve lever to the desired color (Figure 6). Note: For this example we will select YELLOW Figure 4 MH-400 EH models Move the spinner valve lever to the BLUE section (MAX SPEED) (Figure 6).
PAGE 7
Adjusting the Main Hopper Height Using the hydraulic controls on the SH model or the wireless controller on the EH model, adjust the main hopper hydraulic cylinders until the arrow aligns with the GREEN section on the hydraulic cylinder decal (Figure 8) . Figure 7 1. Crank 2. Hydraulic cylinder MH-400 EH models Note: For this example we will select the YELLOW section. Figure 8 Using the wireless controller, set the floor belt speed to the corresponding color. 1. Hydraulic controls 3. Cylinder 2.
PAGE 8
5 7 Operate the Twin Spinner Fine Tuning the Twin Spinner No Parts Required No Parts Required Procedure Procedure 1. Verify that all the settings are correct. Operate the machine to verify that the desired performance is attained. Refer to the MH-400 Operator's Manual for Operating Instructions. 2. If the spread pattern is not to the desired consistency, loosen the handles and slide the hopper in the desired direction to attain the desired spread pattern.
PAGE 9
Notes: 9
PAGE 10
Notes: 10
PAGE 11
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 44944 Serial No.
PAGE 12