Installation Instructions

ManualsBrandsToro ManualsAttachmentsWheel Kit, AccuraSeed 620

FormNo.3444-696RevA

WheelKit

AccuraSeed620

ModelNo.46431

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthetractionunitandattachmentonalevelsurface.

2.Engagethetraction-unitparkingbrake.

3.Lowertheattachment.

4.Shutoffthetraction-unitengineandremovethekey.

5.Iftheattachmentisconnectedtoatractionunit,disconnectit;refertotheoperator'smanualforthe

attachment.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com/bullseye.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3444-696*

Summary of content (8 pages)

PAGE 1
Form No. 3444-696 Rev A Wheel Kit AccuraSeed 620 Model No. 46431 Installation Instructions Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the traction unit and attachment on a level surface. 2. Engage the traction-unit parking brake. 3. Lower the attachment. 4. Shut off the traction-unit engine and remove the key. 5. If the attachment is connected to a traction unit, disconnect it; refer to the operator's manual for the attachment.
PAGE 2
Installing the Wheel Kit No Parts Required Wheel Kit Overview Assembled View g350622 Figure 1 2
PAGE 3
Kit-Only View g350417 Figure 2 1. Cotter pin 4. Hitch 2. Clevis pin 5. Hoses—245 cm (8 ft) 7. Frame and wheel assembly 3. Top link 6. Hoses—165 cm (5.4 ft) and 195 cm (6.4 ft) Removing the Existing Rear-Roller Bearings Refer to Figure 3 for this procedure. 1. Remove the bolts, washers, and nuts that secure the rear roller bearings to the attachment. Retain the washers and locknuts for installation of the pivot plates in step 3 in Installing the Wheels and Frame (page 4). 2.
PAGE 4
g353835 Figure 3 1. Bolt 4. Locknut (M16) 2. Washer (M16) 5. Roller 3. Roller bearing 6. Roller shaft Installing the Wheels and Frame Refer to Figure 4 for this procedure. 1. Use bolts (M12), spring washers (M12), large washers (M12), wheel shafts, wheel bushings, and lock pins to secure the wheels to the frame. 2. Install the pivot plates on the shafts on each side of the roller. 3.
PAGE 5
g346322 Figure 4 1. Bolt (M12) 7. Wheel bushing 13. Washer (M16) 19. Bolt (M16 x 40 mm) 2. Spring washer (M12) 8. Frame 14. Pivot plate 20. Large distance bushing 9. Nut 15. Bolt (M16 x 65 mm) 21. Hydraulic cylinder 16. Large bearing 22. Attachment side plate 3. Large washer (M12) 4. Wheel shaft 10. Small distance bushing 5. Lock pin 11. Bolt (3/4 inch) 17. Large washer (M16) 6. Wheel 12. Locknut (M16) 18.
PAGE 6
Installing the Hydraulic Hoses Refer to Figure 5 for this procedure. 1. Use copper washers (3/8 inch) and nipples (3/8 inch) to secure the 195 cm (6.4 ft) hoses and 165 cm (5.4 ft) hoses to the hydraulic cylinders. 2. Route the 195 cm (6.4 ft) hoses and 165 cm (5.4 ft) hoses along the sides of the attachment and towards the front of the attachment. Figure 1 and Figure 2 illustrate the appropriate hose routing. 3.
PAGE 7
Installing the Hitch g351202 Figure 6 1. Clevis pin 3. Hairpin cotter 2. Top link 4. Link handle 1. Install the link handle through the top link (Figure 6). 2. Secure the hitch to the attachment using the lower hitch pins from the attachment. 3. Secure the top link to the attachment using the upper hitch pins from the attachment. 4. Secure the top link to the hitch using the clevis pin and cotter pin (included as loose parts) as shown in Figure 6. Completing the Installation 1.
PAGE 8