Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpiked Rear Roller, RapidSeed 430

FormNo.3444-776RevB

SpikedRearRoller

RapidSeed430and590

ModelNo.46437

ModelNo.46442

InstallationInstructions

WARNING

Thespikedrearrollerissharpandcaninjureyou.

Wheninstallingthespikedroller,dothefollowing:

•Useapprovedhoistingequipmenttoraisethemachineonly.

•Nevercrawlunderthemachine.

•Weargloves.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheprotectiveplate,rearroller,

scraper,andbrush.

Spikedsegment—RapidSeed430

Spikedsegment—RapidSeed590

Bolt(8x20mm)

Locknut(8mm)

Spacer

Bolt(16x40mm)

Installthespikedrearroller.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthetractionunitandattachmentonalevel

surface.

2.Engagethetractionunitparkingbrake.

3.Lowertheattachment.

4.Shutoffthetraction-unitengineandremovethe

key.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com/bullseye.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3444-776*

Summary of content (8 pages)

PAGE 1
Form No. 3444-776 Rev B Spiked Rear Roller RapidSeed 430 and 590 Model No. 46437 Model No. 46442 Installation Instructions WARNING The spiked rear roller is sharp and can injure you. When installing the spiked roller, do the following: • Use approved hoisting equipment to raise the machine only. • Never crawl under the machine. • Wear gloves. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty.
PAGE 2
Removing the Protective Plate, Rear Roller, Scraper, and Brush No Parts Required Procedure WARNING The machine could fall onto someone and cause serious injury or death. • Do not keep the machine raised on the jack for extended periods of time. • Always use a jack on a level surface. • Do not rely solely on the jack for support. Use adequate jack stands or equivalent support. • Before each use, ensure that the jack and jack stands work properly and that there are no signs of damage. 1.
PAGE 3
4. Remove the rear roller (Figure 2). Retain 3 bolts and 4 locknuts for installing the new spiked rear roller. Note: After removing the 4 bolts, discard the rear-most left bolt. g376217 Figure 2 1. Rear roller 3. Bolt (16 x 40 mm) 2. Locknut (16 mm) 4. Bolt, rear-most (discard) 5. Remove the scraper (Figure 3). Retain the scraper and rear roller when working with a smooth rear roller. g348690 Figure 3 1. Scraper 3. Washer 2. Locknut (10 mm) 4.
PAGE 4
6. Remove the brush (Figure 4). Retain the brush and fasteners for future installation. g348687 Figure 4 1. Brush 2. Locknut (12 mm) 3. Washer 4.
PAGE 5
4. 3 Mount the spiked roller in the forward-most position (Figure 6). Installing the Spiked Rear Roller Parts needed for this procedure: 36 Spiked segment—RapidSeed 430 49 Spiked segment—RapidSeed 590 8 Bolt (8 x 20 mm) 8 Locknut (8 mm) 2 Spacer 1 Bolt (16 x 40 mm) Procedure 1. 2. 3. Install a spacer onto each end of the roller (Figure 5). g348612 Figure 6 Install the spiked segments onto the roller (Figure 5). 1.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8