Form No. 3408-767 Rev D Power Plex™ 33cm 40V MAX String Trimmer/Edger Model No. 51130—Serial No. 317000001 and Up Model No. 51130T—Serial No. 317000001 and Up Register at www.Toro.com.
Safety This product complies with all relevant European directives. For details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING: When using electric gardening appliances, always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury, including the following: WARNING Introduction Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury.
D. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. E. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. F. Keep your hands and feet away from the cutting area. 3. Power tool use and care A. Do not force the power tool. Use the correct power tool for your application.
Sound Pressure This unit has a sound pressure level at the operator’s ear of 83.1 dBA, with an Uncertainty Value (K) of 3 dBA. The sound pressure level was determined according to the procedures outlined in EN ISO 11201. Sound Power This unit has a guaranteed sound power level of 96 dBA, which includes an Uncertainty Value (K) of 1.02 dBA. The sound power level was determined according to the procedures outlined in EN ISO 11094. Hand/Arm Vibration Measured vibration level for right hand = 2.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-2490 136-2490 1. Double insulated 2. Do not discard. decal136-2482 136-2482 1. String trimmer edger decal136-2499 136-2499 1. Read the Operator’s Manual. 2. Do not burn the battery. 3. Do not operate in wet conditions. 4. Do not discard. decal136-2484 136-2484 1. Press to rotate.
decal136-2504 136-2504 1. The battery pack is charging. 3. The battery pack is too warm. 2. The battery pack is fully charged. 4. The battery pack needs to be replaced. decal136-2535 136-2535 1. Warning—keep bystanders away from the machine in all directions. 2. Thrown object hazard—keep bystanders away from the machine. decal136-2534 136-2534 1. The battery does not come out of the box fully charged. 4. Stop—follow these instructions before first use. 2. Place the battery in the battery charger.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Mount the battery charger (optional). No parts required – Unfold the handle. Auxiliary handle 1 Install the auxiliary handle. Guard Phillips head screw 1 3 Mounting the guard to the base of the trimmer. Wire edge guard 1 Installing the edge guard Note: The battery pack is not fully charged when you purchase it.
2 Unfolding the Handle No Parts Required Procedure 1. Unfold the handle (A of Figure 2). 2. Press and hold the locking button on the upper shaft, align the locking button with the slotted hole on the lower shaft, and slide the 2 shafts together. Once the slotted hole on the lower shaft is past the locking button, release the locking button, and slide the lower shaft into the upper shaft until the trimmer is at the desired height (B of Figure 2).
3 4 Installing the Auxiliary Handle Installing the Guard Parts needed for this procedure: Parts needed for this procedure: 1 Auxiliary handle 2. Guard 3 Phillips head screw Procedure Procedure 1. 1 Line up the groove along the handle with the groove on the auxiliary handle and slide the auxiliary handle toward the trimmer handle (A of Figure 3). Snap the handle securely into place (B of Figure 3). 1.
Product Overview 5 Specifications Installing the Edge Guard Weights Parts needed for this procedure: 1 Wire edge guard Procedure Mass of the machine without the battery 3.2 kg (7.0 lb) Mass of the machine with battery 88525 4.2 kg (9.2 lb) Mass of the machine with battery 88526 4.8 kg (10.5 lb) Appropriate Temperature Ranges Slightly spread the ends of the wire edge guard apart and then insert the ends into the holes in the trimmer housing as shown in Figure 5.
Stopping the Trimmer Operation To stop the trimmer, release the trigger. Starting the Trimmer 1. Removing the Battery Pack from the Trimmer Make sure that the vents on the trimmer are clear of any dust and debris. Press the battery latch on the machine to release the battery pack and slide the battery pack out of the machine (Figure 9). g194612 Figure 6 1. Trimmer venting areas g192774 Figure 9 1. Battery latch 2.
Charging the Battery Pack Important: Make sure to read all safety precautions. Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 10). Note: At any time, press the battery-charge-indicator button on the battery pack to display the current charge (LED indicators). 1. Plug the power cord that matches your power outlets into the battery charger. 2. Make sure that the vents on the battery pack are clear of any dust and debris. 3.
Advancing the Line Adjusting the Handle Height Note: The trimmer is equipped with an auto-feed head. 1. With the trimmer running, release the switch trigger. 2. Wait a few seconds, then press the lockout button and squeeze the trigger. 1. Loosen the lower shaft connector (A of Figure 13). 2. Slide the telescoping shaft to your desired position (B of Figure 13).
Adjusting the Auxiliary Handle 1. Release the auxiliary-handle latch (A of Figure 14). 2. Slide the auxiliary handle up or down to your desired height (B of Figure 14). 1. Press the rotator button, rotate the head 90°, and make sure that it locks into place (A of Figure 16). 2. Stand the trimmer on the wheel and begin edging (B of Figure 16). Important: Do not remove the rubber bumper. 3. Close the auxiliary-handle latch to secure the auxiliary handle in place (C of Figure 14).
Maintenance 4. Install the new spool so that the string aligns with the eyelet in the string head. Thread the string into the eyelet. After each use of the trimmer, complete the following: 1. Remove the battery from the trimmer. 5. 2. Wipe the trimmer clean with a damp cloth. Do not hose the trimmer down or submerge it in water. Verify that the end of the string extends approximately 152 mm (6 inches) beyond the slot. 6.
the wound string and the outside edge of the spool. 6. Replace the spool and the spool retainer; refer to Replacing the Spool (page 15). Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 10). Important: If you are storing the tool for a year or longer, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn blue on the battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Problem Possible Cause Corrective Action 1 LED indicator is blinking on the battery pack. 1. The battery pack is low voltage. 1. Place the battery pack on the charger. It is difficult to remove the battery pack from the tool. 1. The battery pack/tool is new or there is corrosion in the battery terminals and/or the terminals on the tool. 1. Clean the terminals on the battery pack and the tool.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
Residential Products The Toro Warranty and The Toro GTS Starting Guarantee Instructions for Obtaining Warranty Service Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have
