&igh tor Biter Ancestral = e metrical Guide Rar e Product & Liston by UNDERWRITERS | LABORATORIES ING.
o @ o WELCOME to the TORO® family of fine lawn and garden equipment. Your TOR ELECTRIC CHAIN SAW features advanced concepts in engineering design and safety. This Operator’s Manual has been designed to help you thoroughly understand your new tool before using it. Please read it completely before operating the tool. You will find that as your knowledge of the tool increases, your proficiency with it will improve. A Pay particular attention to the instructions highlighted by this safety alert symbol.
TOR COMPACT 14” CHAIN SAW MODEL 51140 OPERATOR'S MANUAL A Safety Instructions 1. READ OPERATOR'S MANUAL CAREFULLY. Become fully familiar with the chain saw before attempting to operate it. 2. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 3. AVOID DANGEROUS ENVIRONMENT. Don't expose saw to rain, or use saw in damp or wet locations. Keep work area well lit. NEVER OPERATE THE SAW WHILE IN CONTACT WITH WATER, 4. WEAR PROPER APPAREL. Loos clothing or jewelry may get caught in moving parts.
A Safety Instructions {cont.) 16. CONNECT CHAIN SAW TO CORRECT VOLTAGE (120V). 17. AVOID ACCIDENTAL START. ING. Do not place finger on switch when plugging in or until ready for cutting. Always carry the chain sew from one location to another with the power cord disconnected and finger off of switch, The guide bar and saw chain should be to the rear, and away from your body {see figure 12}, 18.
Assembly Instructions install Guide Bar and Saw Chain 1. Remove the guide bar hexagon nut and spring washer. Then remove sprocket cover (Fig. 11, Figure 1 2. Loosen the guide bar adjusting block by turning the tension adjusting resew counter clockwise to the screw end {Fig. 2). Figure® o = Tension:: prey Guider, Adjudicating Bloke 3. Insert the saw chain into the groove of the guide bar with the citing edge facing forward toward the nose of the guide bar (see inset).
Assembly Instructions {cont.) Adjust Saw Chain Tension Caution: Make sure chain saw is disconnected from power source before adjusting chain tension. Use gloves or rag to protect chancels, IMPORTANT: Do not operate chain saw if chain is not properly adjusted. A Jose chain will shorten sprocket and guide bar life and may cause chain breakage. An over-tightens chain will overheat the guide bar and chain, causing rapid wear and may cause mortar burnout, Figure's Tension T Asininity £ Shrive Gulden Halibut 1.
Before Operating Fill Oif Reservoir CAUTION: Make sure chain saw is disconnected from power source before performing maintenance operations. 1. Remove the oi! fill cap (Fig. 8 g 2. Using a pouring spout or funnel, fill the oil reservoir. When temperature is below 309 Fahrenheit {1°C) use SAE #10 motor oil. For temperatures above 307F (19C} use SAE 430 motor oil. 3. Replace and tighten fill cap immediately after filling, Failure to tighten the cap will cause excessive oil leakage.
Operating Instructions {cont.) Never stand directly behind the chain saw (Fig. 12}, 3. Sand securely with your weight evenly distributed on both feat. 4. Don overreach, balanced. seep yourself 5. Always cut with the spike bar set firmly against the wood. Start saw chain before cutting into wood {Fig. 11} Figaro 71 6. When cutting, keep the nose of the guide bar from contacting logs, branches, the ground or any other obstruction.
Operating Instructions {cont.) Fating a Tree A CAUTION: Rusting standing trees requires expertise and poses hazards. Your TOR Chain Saw should not be used to fell large trees with diameters greater than the length of your guide bar. The proper aerator stance for felling a tree s shown in Figure 15. Figure'ts 1. Before attempting to cut a big tree, practice cut a few branches, limbs or small logs to familiarize yourself with the controls. 2. Next, the direction of the fall must be determined.
Operating Instructions (cont.) 2. Make the second cut two 1o four inches farther out on the limb and from above. Cut until the limb falls, 3. Cut ane third the diameter of the fib stub from underneath a5 close to the trunk as possible. 4. Make the final cut from above so that it meets the previous cut as close as possible to the trunk. Cutting Fallen Trees {Bucking) 1. When cutting branches from a fallen tree of cutting a log into lengths, support the log off the ground {preferably on a sawbuck} 2.
Maintenance Refiling Oil Reservoir CAUTION: Make sure chain saw is disconnected from prows source before performing maintenance operations. 1. Removes the ofl fill cap {Fig. 20). Figure 20 Oiling Button, il Fill Cap 2. Using a pouring spout ar funnel, fill the oil reservoir, When temperature is below 300 Fahrenheit use SAE #10 rotor oil. For temperatures abase 300 use SAE #30 motor oil. 3. Replace and tighten fill cap immediately after filling. Failure to tighten the cap will cause excessive oil leakage.
Maintenance {(cont.) 6. Move 1o other side of chain and file all cutters opposite to complete chain sharpening, File all cutters identically {Fig. 23}. Figure 23 7. Depth gauges should be checked every third sharpening with’ a depth gauge tool. Depth gauge setting is 025" Place the depth gauge tool as indicated and file away portions of each depth gauge which extend above the tool’s slot {Fig. 24).
1 Chain Saw Parts List Part No. Description o 1 346040 Flange Nut 1 2 346150 Shaft Support Bracket 1 3 346370 Oil Cap 1 4 341460 Decal Caution 1 5 34.0080 Decal Chainsaw 1 6 34.0060 Decal Toto 346400 Hex Nut 1 8 346300 Adjusting Block Assembly i 5 338290 Guide Bar i 1 343400 Saw Chain 1 11 345980 Spring Washer 1 12 345970 Nt 1 13 345950 Screw 1 12 240970 Dec at Torah RH.
Toto also has a full line of premium-quality snow thrower products... Model 38010 421 Snow thrower 1 Model 38040 524 Snow thrower Model 38050 724 Snow thrower .
Fern Compact 3 Product Aegis Below is & removable Bro Duct registration ¢ TOR COMPANY, Outdoor Applicant Devi 0 ensure this Toto Product receives proper We have provided you spade to ya cord th Trimmer. Rivieras use this information with a Date of Purchase: Lok Mo Bay v heftily e fading ration Card a1 which we ask that vou compile and send 1o THE soon. IMPORTANT Return of this card is important post sale service. e rads of purchase and the serial bumper of your ny correspondence t THE TOR COMPANY.