Form No. 3417-954 Rev C PowerPlex 13in 40V MAX String Trimmer/Edger Model No. 51481—Serial No. 318000001 and Up Model No. 51481T—Serial No. 318000001 and Up Register at www.Toro.com.
Safety If you have questions or problems, call toll free 1-800-237-2654 (US) or 1-800-248-3258 (Canada) before returning this product. WARNING: When using electric gardening appliances, always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury, including the following: WARNING Failure to follow all warnings and instructions may result in electric shock, fire and/or serious personal injury.
D. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. E. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. F. Keep your hands and feet away from the cutting area. 3. Power tool use and care A. Do not force the power tool. Use the correct power tool for your application.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-2463 136-2463 Model 51481 decal136-2473 decal136-2464 136-2473 136-2464 Model 51481T decal136-2474 136-2474 decal136-2471 136-2471 decal136-2476 136-2476 4 1. The battery pack is charging. 3. The battery pack is too warm. 2. The battery pack is fully charged. 4. Replace the battery pack.
decal136-2482 136-2482 1. String trimmer edger decal136-2534 136-2534 decal136-2484 136-2484 1. The battery does not come out of the box fully charged. 4. Stop—follow these instructions before first use. 2. Place the battery in the battery charger. 5. Read the Operator’s Manual. 3. Wait until the battery is fully charged before the first use. 1. Press to rotate. decal136-2539 136–2539 1. Charge the battery where the temperature is between 0°C and 40°C (32°F and 104°F).
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Mount the battery charger (optional). No parts required – Unfold the handle. Auxiliary handle 1 Install the auxiliary handle. Guard Phillips head screw 1 2 Install the guard. Wire edge guard 1 Install the edge guard. Note: The battery pack is not fully charged when you purchase it.
2 Unfolding the Handle No Parts Required Procedure 1. Unfold the handle (A of Figure 2). 2. Press and hold the locking button on the upper shaft, align the locking button with the slotted hole on the lower shaft, and slide the 2 shafts together. Once the slotted hole on the lower shaft is past the locking button, release the locking button, and slide the lower shaft into the upper shaft until the trimmer is at the desired height (B of Figure 2).
3 4 Installing the Auxiliary Handle Installing the Guard Parts needed for this procedure: Parts needed for this procedure: 1 Auxiliary handle 2. Guard 2 Phillips head screw Procedure Procedure 1. 1 Line up the groove along the handle with the groove on the auxiliary handle and slide the auxiliary handle toward the trimmer handle (A of Figure 3). Snap the handle securely into place (B of Figure 3). 1.
Product Overview 5 Specifications Installing the Edge Guard Appropriate Temperature Ranges Parts needed for this procedure: 1 Wire edge guard Procedure Charge the battery at 0°C (32°F) to 40°C (104°F)* Use products at -15°C (5°F) to 60°C (140°F) Store products at -15°C (5°F) to 60°C (140°F) Unplug the charger if Below 0°C (32°F) or above 40°C (104°F) *Charging time will increase if you do not charge the battery within this range.
Shutting Off the Trimmer Operation To shut off the trimmer, release the trigger. Starting the Trimmer 1. Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, remove the battery pack. Make sure that the vents on the trimmer are clear of any dust and debris. Removing the Battery Pack from the Trimmer Press the battery latch on the machine to release the battery pack and slide the battery pack out of the machine (Figure 9). g194612 Figure 6 1.
Charging the Battery Pack Important: Read all safety precautions. Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 9). Note: At any time, press the battery-charge-indicator button on the battery pack to display the current charge (LED indicators). 1. Make sure that the vents on the battery pack are clear of any dust and debris. 2. Line up the cavity in the battery pack (Figure 10) with the tongue on the charger.
Advancing the Line Manually Adjusting the Auxiliary Handle Remove the battery from the trimmer, then push the button at the base of the spool retainer while pulling on the trimmer line to manually advance the line. 1. Release the auxiliary-handle latch (A of Figure 14). 2. Slide the auxiliary handle up or down to your desired height (B of Figure 14). Important: Do not remove the rubber bumper. 3. Close the auxiliary-handle latch to secure the auxiliary handle in place (C of Figure 14).
Edging To use the trimmer as an edger, refer to the following steps: 1. Press the rotator button, rotate the head 90°, and make sure that it locks into place (A of Figure 15). 2. Stand the trimmer on the wheel and begin edging (B of Figure 15). g203809 Figure 17 1. Direction of rotation g203808 Figure 16 Operating Tips • Keep the trimmer tilted toward the area being cut; this is the best cutting area. • The string trimmer cuts when you move it from left to right.
Maintenance 4. Install the new spool so that the string aligns with the eyelet in the string head. Thread the string into the eyelet. 5. Verify that the end of the string extends approximately 152 mm (6 inches) beyond the slot. 6. Pull the string extending from the string head so that the string releases from the slot in the spool. 7. Install the spool retainer by pressing the tabs into the slots and pushing down until the spool retainer clicks into place.
the wound string and the outside edge of the spool. 6. Replace the spool and the spool retainer; refer to Replacing the Spool (page 14). Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 9). Important: If you are storing the tool for a year or longer, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn blue on the battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Problem Possible Cause Corrective Action 1 LED indicator is blinking on the battery pack. 1. The battery pack voltage is low. 1. Place the battery pack on the charger. It is difficult to remove the battery pack from the tool. 1. The battery pack/tool is new or there is corrosion in the battery terminals and/or the terminals on the tool. 1. Clean the terminals on the battery pack and the tool.
Notes:
Notes:
