Form No. 3450-392 Rev B Flex-Force Power System™ 60V MAX Power Head Model No. 51810T—Serial No. 321000001 and Up Register at www.Toro.com.
the location of the model and serial numbers on the product. Write the numbers in the space provided. For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
Safety The Model 51810T Power Head is compatible with a variety of Toro-approved attachments that, when combined, comply with specific standards; see the following table for more detail. Combination Power Head Model Attachment Standard Model String Trimmer 51810T 88716 Conforms to UL STD 82 Certified to CSA STD C22.2 No. 147 Edger 51810T 88710 Conforms to UL STD 82 Certified to CSA STD C22.2 No.
6. Do not use non-rechargeable batteries. 7. Charge the battery pack with only the battery charger specified by Toro. A charger suitable for 1 type of battery pack may create a risk of fire when used with another battery pack. 8. Charge the battery pack in a well-ventilated area only. 9. Do not expose a battery pack or battery charger to fire or to temperatures higher than 100°C (212°F). 10.
7. Do not attempt to service or repair the appliance, battery pack, or battery charger except as indicated in the instructions. Have an Authorized Service Dealer perform service using identical replacement parts to ensure that the product is safely maintained. 8. Store an idle appliance indoors in a place that is dry, secure, and out of the reach of children. 9. Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
Setup 1 Installing the Auxiliary Handle Parts needed for this procedure: 1 Auxiliary handle assembly Procedure 1. Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using the provided Allen wrench (A of Figure 3). 2. Line up the auxiliary handle with auxiliary handle plate on the trimmer handle (B of Figure 3). 3. Secure the auxiliary handle to the handle plate with the 4 socket head screws previously removed (C of Figure 3).
Operation Product Overview Starting the Attachment WARNING Do not attempt to operate the power head without an attachment installed. Read and follow the Operator’s Manual for your specific attachment before operating the power head. 1. Ensure that the vents on the attachment, power head, and battery are clear of any dust and debris. 2. Align the cavity in the battery pack with the tongue on the handle housing (Figure 5). g372329 Figure 4 1. Battery latch 4.
Removing the Attachment from the Power Head To remove the attachment from the power head, refer to the Operator’s Manual for your attachment. g357456 Figure 6 1. Lockout button 3. Run trigger 2. Variable-speed switch Shutting Off the Attachment To shut off the attachment, release the run trigger. Whenever you are not using the attachment or are transporting the trimmer to or from the work area, remove the battery pack.
Maintenance Storage After each use of the power head, complete the following: Important: Store the tool, battery pack, and 1. Remove the battery from the power head. 2. Wipe the power head clean with a damp cloth. Do not hose the power head down or submerge it in water. 3. Check and tighten all fasteners. If any part is damaged or lost, repair or replace it. 4. Brush debris away from air intake vents and exhaust on motor housing to prevent the motor from overheating. 5.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
