Form No. 3432-903 Rev D Flex-Force Power System™ 60V MAX String Trimmer Model No. 51835T—Serial No. 320000001 and Up Register at www.Toro.com.
Safety For assistance, please see www.Toro.com/support for instructional videos or contact your Authorized Service Dealer before returning this product. WARNING—When using electric gardening appliances, always read and follow basic safety warnings and instructions to reduce the risk of fire, electric shock, and personal injury, including the following: IMPORTANT SAFETY INSTRUCTIONS I. Training Introduction 1.
7. Charge the battery pack with only the battery charger specified by Toro. A charger suitable for one type of battery pack may create a risk of fire when used with another battery pack. 8. Charge the battery pack in a well-ventilated area only. 9. Do not expose a battery pack or battery charger to fire or to temperatures higher than 68°C (154°F). 10. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions.
7. Do not attempt to service or repair the appliance, battery pack, or battery charger except as indicated in the instructions. Have an Authorized Service Dealer perform service using identical replacement parts to ensure that the product is safely maintained. 8. Store an idle appliance indoors in a place that is dry, secure, and out of the reach of children. 9. Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. 0.095” (2.4mm) diameter twisted nylon line / fi l en nylon torsadée de 2,4 mm (0.095”) de diamètre 0.08” (2.0mm) diameter nylon line / fi l en nylon de 2,0 mm (0.08”) de diamètre 60V MAX* DC STR ING TRIMMER/ DÉBROUSSAILLEUSEÀ FIL *Battery manufacturer rating = 60V maximum & 54V nominal.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. Allen wrench 1 Unfold the shaft. Auxiliary handle assembly 1 Install the auxiliary handle. Guard 1 Install the guard. String trimmer strap 1 Install the strap. 1 Unfolding the Shaft Parts needed for this procedure: 1 Allen wrench Procedure 1. Unfold the shaft (A of Figure 1). 2.
g280969 Figure 1 7
2 Installing the Auxiliary Handle Parts needed for this procedure: 1 Auxiliary handle assembly Procedure 1. Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using the provided Allen wrench (A of Figure 2). 2. Line up the guides on the auxiliary handle plate to the guide on the bottom of the trimmer shaft (B of Figure 2). 3. Line up the auxiliary handle with auxiliary handle plate on the trimmer shaft (C of Figure 2). 4.
3 Installing the Guard Parts needed for this procedure: 1 Guard Procedure 1. Using the provided Allen wrench, remove the 2 socket head screws, 2 washers, and 2 spacers from the trimmer base (A of Figure 3). 2. Align the guard onto the trimmer base (B of Figure 3). 3. Secure the guard onto the base of the trimmer with the 2 socket head screws, 2 washers, and 2 spacers previously removed (C of Figure 2).
If there is ever an emergency and you need to rapidly remove the harness, disconnect the quick-release buckle as follows: 4 1. Press in on the sides of the buckle (A of Figure 5). 2. Allow the buckle to disconnect (B of Figure 5). Installing the Strap Parts needed for this procedure: 1 String trimmer strap Procedure If you are using the machine with battery Model 81860 or 81875, a string trimmer strap is recommended.
Product Overview Operation Specifications Starting the Trimmer 1. Appropriate Temperature Ranges Charge/store the battery pack at 5°C (41°F) to 40°C (104°F)* Use the battery pack at -30°C (-22°F) to 49°C (120°F) Use the trimmer at 0°C (32°F) to 49°C (120°F) Store the trimmer at 0°C (32°F) to 49°C (120°F)* Make sure that the vents on the trimmer are clear of any dust and debris. *Charging time will increase if you do not charge the battery within this range.
Advancing the Line Using the Bump Feed g268420 Figure 8 1. Speed range switch 1. Run the tool at full throttle. 2. Tap the bump button on the ground to advance the line. The line advances each time the bump button is tapped. Do not hold the bump button on the ground. Note: The line trimming cut-off blade on the 3. Variable-speed trigger grass deflector cuts the line to the correct length. 2.
Adjusting the Cutting Swath The trimmer comes from the factory with a cutting swath of 36.6 cm (14 inches) as shown in A of Figure 11. Refer to the following instructions to adjust the swath to 40.6 cm (16 inches) as shown in D of Figure 11. 1. Remove the swath blade from the bottom of the guard by removing the 2 screws holding it in place using the provided Allen wrench (B of Figure 11) and rotate the swath blade 180°. 2.
Maintenance After each use of the trimmer, complete the following: 1. Remove the battery from the trimmer. 2. Wipe the trimmer clean with a damp cloth. Do not hose the trimmer down or submerge it in water. CAUTION The line cutoff blade on the deflector is sharp and can cut you. Do not use your hands to clean the deflector shield and blade. 3. Wipe or scrape clean the cutting head area any time there is an accumulation of debris. 4. Check and tighten all fasteners.
Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 11). Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
