Form No. 3440-113 Rev A Flex-Force Power System™ 24in 60V Hedge Trimmer Model No. 51841—Serial No. 320000001 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code (if equipped) on the serial number plate to access warranty, parts, and other product information. For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Safety WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 6. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. III. Personal safety IMPORTANT SAFETY INSTRUCTIONS 1.
V. Battery tool use and care action can cause severe injury within a fraction of a second. 1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 3.
VII. Hedge trimmer safety warnings 1. Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury. 2. Carry the hedge trimmer by the handle with the blade stopped and taking care not to operate any power switch.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal144-3098 144-3098 decal144-3094 144-3094 1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature range. 2. The battery pack is fully charged. 4.
decal140-8475 140-8475 1. Read the Operator’s Manual. 2. Call2Recycle® battery recycling program 3. Keep away from open fire or flames. 4. Do not expose to rain. decal144-3087 144-3087 1. Warning—read the Operator’s Manual; wear eye protection; do not expose to rain. 2. Cutting/dismemberment hazard of hand—stay away from moving parts; keep all guards and shields in place. decal137-9461 137-9461 1.
Setup Product Overview Note: The battery pack is not fully charged when it is purchased. Before using the machine for the first time, refer to Charging the Battery Pack (page 11). g308470 Figure 2 Left side of the machine shown. 1. Blades 2. Guard 6. Lock switch 7. Trigger 3. Auxiliary-handle switch 8. Battery latch 4. Auxiliary handle 9. Battery pack 5. Handle-rotation button 10. Protective cover g330065 Figure 3 1. Battery charger Model 88610 (included with Model 51841) 8 2.
Specifications Operation Model 51841 Cutting Length 610 mm (24 inches) Rated Voltage 60V DC maximum, 54 VDC nominal usage No-load Speed 3200 spm at 60 VDC max Cutting width 19 mm (3/4 inch) Charger Type 88602 or 88610 (included with 51841) Battery Type 88620 (included with 51841), 88625, 88640, 88660, or 88675 Starting the Hedge Trimmer 1. Remove the protective cover from the blades (Figure 4). WARNING The hedge trimmer blades can cause cuts or amputation.
5. Shutting Off the Hedge Trimmer Press the lock switch and then squeeze the trigger switch while engaging the auxiliary-handle switch to turn on the hedge trimmer (Figure 5). To shut off the hedge trimmer, release the trigger, auxiliary-handle switch, or both (Figure 5). Allow at least 5 seconds for the cutting blade to stop moving. The trimmer stays on as long as the auxiliary-handle switch is engaged and the trigger is squeezed.
Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions. Battery pack and/or battery charger is over or under the appropriate temperature range Red blinking Battery pack charging fault* *Refer to Troubleshooting (page 13) for more information.
Maintenance Storage Remove the battery pack before maintenance or cleaning work. Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 9). Use only the manufacturer’s recommended replacement parts and accessories. Important: If you are storing the battery pack for the off-season, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn green on the battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
