Operator's Manual

11
Your power pack has enough output for the lights that
came in your kit However, you can add fixtures to
some kits. Also, you can increase the bulb wattage to
some fixtures (see each fixture for the maximum bulb
wattage it will handle). Just make sure the total lamp
load doesn’t exceed your power pack’s output rating.
Your power pack’s maximum OUTPUT is listed on the
front above the model number:
To find out your lamp load, add the bulb wattages of
your fixtures. EXAMPLE: Ten fixtures, each with
7-watt bulbs = 70-watt lamp load.
Maximum number of lights
for each type of power pack:
Maximum Output Bulb Wattage
4 7 12 18
Maximum number of lights
21 watt 5 3 1 1
36 watt 9 5 3 2
40 watt 10 5 3 2
49 watt 12 7 4 2
56 watt 14 8 4 3
72 watt 18 10 6 4
80 watt 20 11 6 4
84 watt 21 11 6 4
98 watt 24 14 8 5
152 watt 38 21 12 8
160 watt 40 22 13 8
Power Pack
Bloc D’alimentation
Paquete de Energía
CAUTION: SUITABLE FOR OUTDOOR USE ONLY
USE ONLY TORO TYPE T-5 BULBS RATED 18W MAXIMUM
MOUNT AT LEAST 30 CM (1 FOOT) ABOVE GROUND.
Input: 120 V 60 Hz 1.0 A Output: Max XXX W 12 V AC lamp load
Not for use with a dimmer
ATTENTION: POUR UTILISATION A L'EXTERIER SEVLEMENT
UTILISER SEULMENT DES AMPOULES TORO DE TYPE T-5
INSTALLER A AU MOIN 30 CM AU-DESSUS DU SOL.
Energlo d''entré: 120 V 60 Hz 1.0 A Puissance de sortie:
XXXW Max charge de lampo 12 V C.A.
Ne pas utilliser avec un régulateur de tension
PRECAUCION: APTO SOLAMENTE PARA USO EN EXTERIORES
USE SOLO BOMBILLAS TORO TIPO T-5 CON CAPACIDAD
COLOCAR POR LO MENOS A 30 CM (1 PIE) DEL SUELO
Entrada: 120 V 60 Hz 1.0 A Salida: Max XXX W 12 VCA
carga de bombillas. No user con un atenuador de corrienta.
SERIAL NUMBER/NUMERO DE SERIE:
Model/ModelModèle: 1 2 3 4
®
• Fixtures do not light
– Make sure your power pack is plugged in and
your outlet is working.
– You have a photo-cell controlled timer. If it is
daylight, the photo cell must be covered with
tape or other material to simulate darkness.
Make sure the tape or material is heavy and
dark so that no light gets through. The tape
must be removed after installation.
– Contact points in the fixture may be bent.
Straighten the contacts to align with the copper
wire inside the cable.
– A fixture might have a defective bulb. Test by
using another bulb. A defective bulb in one
fixture will not affect the operation of the other
fixtures.
• Lights turn on and off at night.
Make sure a fixture from your lighting set is not
facing your photo cell. See if other light sources
(such as headlights or reflections from a window)
are triggering the photo cell.
• Lights stay off at night.
Make sure the photo cell isn’t getting light from a
street light, porch light or other light sources. Check
connections in the fixtures or cable connector.
• Lights go on, then shut off for about 5–20
minutes, then go on (and the cycle repeats).
See Overloads, page 3.
To order additional parts or for technical assistance:
1 [phone]
5 Adding Additional Fixtures...
4 Troubleshooting