Installation Instructions

ManualsBrandsToro ManualsLawn TractorsToro 59184

Printed in the USA

 2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Twin Bagger Grass Catcher

Rear Engine Rider and Lawn Tractor Attachment

Model No. 59184

Form No. 3314-405 Rev A

Installation Instructions

Setup

Updating the Stand Bars

(Rear Engine Riders Only)

Note: Step 1 pertains to riders with serial numbers

6000001 through 6999999, while step 2 is for riders with

serial number prior to 6000001.

1. Using dimensions shown in Figure 1, locate and drill a

9/16 in. diameter hole in each rear stand bar.

Figure 1

2. If rider is equipped with round type stand bars (Fig. 2),

they must be replaced with new ones, Toro Part No.

56-7440 (right-hand) and 56-7450 (left-hand). Stand

bars may be purchased from your local authorized

Toro dealer.

Figure 2

Installing the Mounting Bracket

(Lawn Tractors Only)

Note: Step 1 pertains to tractors with serial numbers

7000001 and Up while step 2 pertains to tractors with

serial number prior to 7000001.

1. Secure mounting bracket (supplied with tractor) to rear

frame with 2 capscrews (5/16 x 3/4 in.) and locknuts

(Fig. 3).

Figure 3

2. Mounting bracket, Toro Part No. 61-9730, must be

purchased from your local authorized Toro dealer.

After bracket is obtained, install it as instructed in

step 1.

Assembling the Mounting Frame to the

Grass Catcher Cover

1. Loosely secure mounting frame to grass catcher cover

with backup plate, 4 capscrews (5/16 x 1 in.), flat

washers, and locknuts (Fig. 4 and 5). Position the

washers on the outside of the grass catcher cover with

the backup plate inside the cover.

Summary of content (4 pages)

PAGE 1
Form No. 3314-405 Rev A Twin Bagger Grass Catcher Rear Engine Rider and Lawn Tractor Attachment Model No. 59184 Installation Instructions Installing the Mounting Bracket (Lawn Tractors Only) Setup Updating the Stand Bars (Rear Engine Riders Only) Note: Step 1 pertains to tractors with serial numbers 7000001 and Up while step 2 pertains to tractors with serial number prior to 7000001.
PAGE 2
. Rotate grass catcher up so mounting pins line up with mounting holes in tractor mounting bracket or rider stand bars. Push pins through holes and retain with hairpin cotters (Fig. 7). Figure 4 2. Secure mounting frame to grass catcher cover frame with 2 capscrews (3/8 x 1 in.), flat washers, and locknuts (Fig. 5). Position the washers on the top side of the assembly. Tighten all mounting fasteners. Figure 7 3.
PAGE 3
Figure 9 Figure 11 Note: Plastic lawn bags may be inserted inside cloth bags to aid in disposal of grass clippings. 3. After chute assembly and duct are assembled, slide duct onto grass catcher. To ease in the installation of plastic bags, insert bag handles into frame brackets from the rear as shown in Figure 10, and insert plastic bags. 4. Slide chute assembly under deflector. Hook rear chute bracket around pivot post on deck. Slide front of chute into locking position with mating part of hinge lock.
PAGE 4
• Overlap swaths to produce an even cutting pattern and to minimize the load on the engine. Make sure grass clippings move continuously through the duct. propel grass clippings, there must be a source for this air. And if the source is obstructed, conveying will be inefficient. Thus, the height-of-cut must not be set too low, because grass surrounding the mower housing will prevent air from getting under the housing and entering the conveying system.