Operator's Manual

AdjustingtheBeltGuide
Note:T oaccessthebeltguide,removethedivider
plate;refertoRemovingtheDividerPlate(page26).
Guideairgap:2.5to4.0mm(3/32to5/32inch)
1.Parkthemachineonalevelsurfaceandshut
offtheengine.
2.Allowthemachinetocool.
3.Disconnectthewirefromthesparkplug;referto
DisconnectingtheSpark-PlugWire(page25).
4.EnsurethattheclutchleverisintheONposition.
5.Ensurethatthebelttensioniscorrect;referto
AdjustingtheBeltT ension(page39).
6.Checkthattheairgapbetweenthebeltguide
andthebeltsis2.5to4.0mm(3/32to5/32
inch);refertoFigure66.
g020011
Figure66
1.Enginepulleys4.Beltguide
2.Belts5.Bolt
3.Guideairgap:2.5to4.0
mm(3/32to5/32inch)
7.Iftheairgapisnotwithinthespeciedrange,
dothefollowing:
A.Loosentheboltthatsecuresthebeltguide
totheengine(Figure66).
Important:Ensurethatthebeltguideis
towardtheenginepulley.
B.Rotatethebeltguideupordownuntilthere
isanairgapof2.5to4.0mm(3/32to5/32
inch)betweentheguideandeachbelt
(Figure66).
Important:Thebeltguideshouldnot
contactthebeltswiththeclutchleverin
theONposition.
Note:Iftheairgapbetweenthebeltguide
andbothbeltscannotbeattained,then1of
thebeltsistoolong.
C.Tightentheboltthatsecuresthebeltguide
totheengine(Figure66).
D.Checktheclutchoperation;referto
CheckingtheClutchOperation(page42).
8.Installthedividerplate;refertoInstallingthe
DividerPlate(page26).
CheckingtheClutchOperation
ServiceInterval:Every40hours
Important:Thepaddlesmustnotrotateinan
emptydrumwhentheclutchleverisintheOFF
position.
1.MovetheclutchlevertotheOFFposition.
2.Starttheengine.
3.Ifthepaddlesrotatewiththeclutchlevertothe
OFFpositiondothefollowing:
A.Shutofftheengine.
B.Checktheairgapbetweenthebeltguide
andthebelts.
Note:Iftheairgapislargerthan4.0mm
(5/32inch),decreasethegapbetweenthe
beltguideandthebelts;refertoAdjusting
theBeltGuide(page42).
4.Repeatsteps1through3untilallthefollowing
conditionsaremet:
•Theengineisrunat2/3throttle.
•TheclutchleverisintheOFFposition.
•Thepaddlesdonotrotateinanemptydrum
whiletheengineisrunning.
AligningthePulleys
1.Parkthemachineonalevelsurfaceandshut
offtheengine.
2.Allowthemachinetocool.
3.Disconnectthewirefromthesparkplug;referto
DisconnectingtheSpark-PlugWire(page25).
4.Removethedividerplate;refertoRemovingthe
DividerPlate(page26).
5.Placeastraightedgeacrossthefaceofthe
enginepulleyandidlerpulley(Figure67).
42