Form No. 3377-600 Rev B Trailer Light Kit Side-Dump Mixers Model No. 68062 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
1 2 Installing the Brackets Installing the Wires Parts needed for this procedure: Parts needed for this procedure: 2 Bracket 1 Wire harness 4 Bolt 7 Cable clamp 4 Nut 4 Edge clip—parallel 1 Edge clip—perpendicular 2 Fir-tree mount 5 Bolt 5 Nut 5 Cable tie 2 Grommet Procedure 1. Align the bolt holes of a bracket with the bolt holes in the side frame rail under the cowl (Figure 1). Note: For older models, drill (2) 7.5 mm (9/32 inch) holes on each side of the frame, spaced 5.
. Route the wire harness as shown in Figure 4, Figure 7, or Figure 8, depending on the model. 2 1 3 4 2 4 4 G021626 Figure 4 Concrete mixers (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4.
1 G021630 Figure 6 Frame without hole 1. Edge clip location 1 2 4 2 3 4 G021627 Figure 7 Belt-drive mortar mixers (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4.
1 2 4 4 G021628 3 Figure 8 Gear-box mortar mixer (frame underside shown for clarity) 1. Edge clip 3. Wire harness 2. Excess wire 4. Cable clamp 4. Use cable clamps and edge clips to secure the wire harness along the inside of the frame (Figure 9). 1 2 1 G020912 G020980 Figure 9 1. Cable clamp Figure 10 2. Edge clip 1. Nut and bolt Note: To use a cable clamp, spread it apart and fit the wire harness into it. Then squeeze the clamp back together.
3 Installing the Lights 1 Parts needed for this procedure: 2 2 Light 3 1 License-plate holder 4 Nut G02091 1 Figure 11 1. Grommet 2. Fir-tree mount Procedure 3. Cable tie 1. Position the license-plate holder onto the posts of the light with the clear bottom lens, so that the clear lens is facing the license-plate holder (Figure 13). 6. Slide the grommet over the 4-pin connector (Figure 12) on the front of the wire harness, and install it in the hole in the front post (Figure 11).
1 2 3 1 G020914 Figure 14 Right light G020921 1. Green wire—stop and turn Figure 16 Model 68024 3. White wire—ground 2. Brown wire—tail light 1. Reflector 4 2. Insert a bolt through the reflector and the frame, and install a nut on the other side. 3. Use a wrench on the bolt and another wrench on the nut to tighten them until they are snug. Installing the Reflectors Important: Do not overtighten the nuts and bolts, or the plastic reflectors will break.
5 A B C D E F Replacing the Light Bulbs No Parts Required Replacing the Rear-facing Bulbs Note: The left rear-facing bulb also illuminates license plate. G020830 Figure 18 1. Use a screwdriver to remove the 4 screws from the large square lens on the light (Figure 17). A B 2. Remove the lens (Figure 18). C 3. Pull the bulb out of the socket (Figure 18). 4. Push a new 168 bulb into the socket (Figure 18). 5. Install the lens and the 2 screws (Figure 18). D E F G020829 Figure 17 2.
