Form No. 3429-928 Rev B MB TX 2500 Tracked Mud Buggy Model No. 68138—Serial No. 404320000 and Up Model No. 68138G—Serial No. 404320000 and Up Model No. 68138HD—Serial No. 404320000 and Up Register at www.Toro.com.
Introduction It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire. This machine is intended to be used by professional, hired operators in commercial applications.
Contents serious injury or death if you do not follow the recommended precautions. Safety ....................................................................... 4 Safe Operating Practices.................................... 4 Safety and Instructional Decals .......................... 6 Product Overview ................................................... 10 Controls ........................................................... 10 Specifications ...................................................
Safety Improper use or maintenance of the machine can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety-alert symbol (Figure 2), which means Caution, Warning, or Danger—personal safety instruction. Failure to comply with the instruction may result in personal injury or death. Safe Operating Practices WARNING Engine exhaust contains carbon monoxide, an odorless gas that is lethal if inhaled.
• Raising the hopper on a slope affects the stability • Use care when approaching blind corners, shrubs, of the machine. Keep the hopper in the lowered position when on slopes. trees, or other objects that may obscure vision. • Ensure that the area is clear of other people before • When operating on a slope, fold the platform up operating the machine. Shut off the machine if anyone enters the area. and walk behind the machine until it is on flat ground. • Never leave a running machine unattended.
• Use jack stands to support components when • Battery gases can explode. Keep cigarettes, required. sparks, and flames away from the battery. • Carefully release pressure from components with • Keep all parts in good working condition and all stored energy. hardware tightened. Replace all worn or damaged decals. • Keep your hands and feet away from moving • Use the cylinder lock to secure the hopper in the parts. If possible, do not make adjustments with the engine running. raised position.
decal132-9051 132-9051 1. Tie-down point decal125-4967 125–4967 decal132-9052 1. Lift point 132-9052 1. Main (15 A) 3. Logic (7.5 A) 2. Auxiliary (15 A) decal132-8961 132-8961 1. Battery charging condition 4. Hopper is lowering. 2. Hour meter 5. Hopper is down. 3. Hopper is raising. 6. Hopper is lowering automatically. decal137-0575 137-0575 1. Read the Operator’s Manual. 2. Transmission fluid decal133-8062 133-8062 7 3.
decal137-8899 137-8899 1. Read the Operator’s Manual.
decal137-3715 137-3715 1. Parking-brake release 7. Explosion hazard—shut off the engine; 13. Lower hopper no fire or open flames while fueling. 2. Parking brake 8. Tipping hazard—do not drive forward 14. Move the handles in to operate. with the hopper raised; do not drive down slopes with the hopper raised; do not drive across slopes with the hopper raised; drive slowly with the hopper lowered. 3. Warning—read the Operator’s Manual; 9. Warning—keep bystanders away; look 15.
Parking Brake Lever Product Overview To engage the parking brake, pull back the lever. (Figure 4). To disengage the parking brake, push the lever forward. Hour Meter The hour meter records the number of hours the engine has operated. It operates when the engine is running. Use these times for scheduling regular maintenance (Figure 4). Choke Control g038268 Use the choke to start a cold engine. Pull the choke knob up to engage it. Push the choke knob down to disengage it (Figure 4). Figure 3 1.
Specifications Operation Note: Specifications and design are subject to Note: Determine the left and right sides of the machine from the normal operating position. change without notice. Width 90.2 cm (35-1/2 inches) Length 268.0 cm (105-1/2 inches) Height 121.2 cm (47.7 inches) Weight 734 kg (1,619 lb) Hopper capacity Maximum load Discharge Height Important: Before operating, check the fuel and oil level, and remove debris from the machine.
DANGER DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. In certain conditions during fueling, static electricity can be released causing a spark, which can ignite the fuel vapors. A fire or explosion from fuel can burn you and others and can damage property. • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills.
Using Stabilizer/Conditioner Performing Daily Maintenance Use fuel stabilizer/conditioner in the machine to keep the fuel fresh longer when used as directed by the fuel-stabilizer manufacturer. Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 19). Important: Do not use fuel additives containing methanol or ethanol. Add the amount of fuel stabilizer/conditioner to fresh fuel as directed by the fuel-stabilizer manufacturer.
Operating the Throttle Starting the Engine The throttle control moves between FAST and SLOW positions (Figure 7). 1. Engage the parking brake. 2. Engage the choke. Always use the FAST position when moving the machine. Note: A warm or hot engine may not require choking. You may need to repeat the starting cycle when you start the engine for the first time after you have filled a completely empty fuel system with fuel. g008946 Figure 7 3. Move the throttle between the FAST and SLOW positions. 4.
Shutting Off the Engine 1. Move the throttle between the FAST and SLOW positions. 2. Engage the parking brake. 3. Turn the key switch to the OFF position and remove the key. Removing Debris from the Machine 1. Park the machine on a level surface, move the motion-control levers to the NEUTRAL-LOCK position, engage the parking brake, and lower the hopper. 2. Shut off the engine and remove the key. Allow the engine to cool. 3. Clean the inside of the hopper using a hose.
Raising the Hopper without Power Lowering the Hopper without Power 1. Install the cylinder lock; refer to Installing the Cylinder Lock (page 20). 2. Ensure that the tub is empty. 3. Place a large drain pan under the hydraulic-manifold block (Figure 12). 1. Raise the machine and support it using jack stands rated for the weight of the machine; refer to Specifications (page 11). 2. Place a large drain pan under the hopper lift cylinder (Figure 13). g186548 Figure 12 g288638 Figure 13 1.
Moving a Non-Functional Machine Transporting the Machine Use a heavy-duty trailer or truck with full-width ramps to transport the machine. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.
Lifting the Machine Hoist the machine using 2 lift points under the hopper and 2 rear tie-down loops. Tilt the hopper forward to locate the 2 lift loops and attach a chain or straps at each of the loops as shown in Figure 17. Note: Take up the slack in the chain or straps to properly balance the unit. g194436 Figure 17 1. Lift points under hopper 2.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Check and adjust the track tension (every 10 hours until 50 hours). Before each use or daily • • • • • • • • Check the engine-oil level. Clean the blower housing (more often under extremely dusty, dirty conditions). Check the condition of the track. Check the parking brake operation.
Pre-Maintenance Procedures Releasing the Cushion for Rear Access You can release the cushion for rear access to the machine for maintenance or adjustment. 1. Lower the platform. 2. Loosen the twist knobs on each side of the machine (Figure 18). g185887 Figure 19 1. Cylinder lock 4. g032556 2. Cushion 3. Remove the cushion and lower it to the platform. 4. Perform any maintenance or adjustment on the machine. 5. Raise the cushion, and slide it onto the pins on both sides of the machine. 6.
Lubrication Engine Maintenance Greasing the Machine Servicing the Air Cleaner Service Interval: Every 50 hours Service Interval: Every 25 hours—Service or replace the air-cleaner foam element (more often under extremely dusty, dirty conditions). When operating the machine under normal conditions, lubricate all grease fittings for the bearings and bushings with No. 2 lithium grease. Lubricate the bearings and bushings immediately after every washing, regardless of the interval listed.
Checking the Engine-Oil Level Service Interval: Before each use or daily Important: Remember to add 80% of the oil, and then gradually fill it to the Full mark on the dipstick. Important: Do not run the engine with the oil level above the Full mark or below the low mark. Otherwise, you may damage the engine. g028106 Figure 22 1. Air-cleaner cover 3. Paper element 1.
Changing the Engine Oil and Filter Service Interval: Every 100 hours Oil Type:: Detergent oil (API service SJ or higher) Engine Oil Capacity: 1.9 L (64 fl oz) g185888 Viscosity: Refer to the table below. g031623 Figure 25 g017552 Figure 24 B. Change the engine oil while the engine is warm. 4. Note: Dispose of the used oil at a recycling center. 1.
g243623 Figure 27 g027477 Figure 26 5. Servicing the Spark Plugs Slowly pour approximately 80% of the specified oil into the filler tube (Figure 27). Service Interval: Every 100 hours—Check the spark plug. Every 300 hours—Replace the spark plug. The spark plugs are RFI compliant. Equivalent alternate brand plugs can also be used. Type: Champion XC12YC Air Gap: 0.76 mm (0.
Removing the Spark Plug Installing the Spark Plug 1. Park the machine on a level surface, move the motion-control levers to the NEUTRAL-LOCK position, engage the parking brake, and lower the hopper. 2. Shut off the engine and remove the key. Allow the engine to cool. 3. Before removing the spark plug(s), clean the area around the base of the plug to keep dirt and debris out of the engine. 4. Remove the spark plug (Figure 28).
Draining the Fuel Tank Fuel System Maintenance You can drain the fuel tank by removing it and pouring the fuel out of the fill neck; refer to Removing the Fuel Tank (page 27). You can also drain the fuel tank by using a siphon in the following procedure. Replacing the Fuel Filter Service Interval: Every 100 hours/Yearly (whichever comes first) (more often under dusty, dirty conditions). 1.
Removing the Fuel Tank 1. Lower the platform. 2. Release the cushion; refer to Releasing the Cushion for Rear Access (page 20). 3. Remove the cross bracket (Figure 33). Electrical System Maintenance Servicing the Battery Service Interval: Every 50 hours DANGER Battery electrolyte contains sulfuric acid, which is fatal if consumed and causes severe burns. Do not drink electrolyte and avoid contact with skin, eyes or clothing.
Charging the Battery WARNING Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from battery. Important: Always keep the battery fully charged (1.265 specific gravity) to prevent battery damage when the temperature is below 0°C (32°F). 1. Remove the battery from the chassis; refer to Removing the Battery (page 27). 2. Perform the following steps to check the electrolyte level: A. Ensure that the cell covers are free from dirt and debris.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses and requires no maintenance. If a fuse blows, check the component or circuit for a malfunction or short. Servicing the Tracks 1. Release the cushion from the rear of the machine. 2. Pull out the fuse to remove or replace it (Figure 36). 3. Install the cushion to the rear of the machine. Service Interval: Before each use or daily—Check the condition of the track.
Adjusting the Track Tension If you place the tab of the tensioning tool along the rear edge of the tension nut, the other end of the tensioning tool should align with the edge of the tension arm as shown in Figure 38. If the distance is not correct, adjust the track tension using the following procedure: Note: If the tensioning tool is not available, the 4. Raise the machine so that the tracks are off the ground. 5. Clean the drive sprocket, the front wheel, and the road wheels.
8. 9. 10. 11. 12. 13. 14. Inspect the condition of the wheels. If the wheels show signs of wear, replace them at this time. Beginning at the drive sprocket, coil the new track around the sprocket, ensuring that the lugs on the track fit between the spacers on the sprocket (Figure 39). Push the track under the lugs and between the road wheels (Figure 39). Starting at the bottom of the front wheel, install the track around the wheel by rotating the track rearward while pushing the lugs into the wheel.
Controls System Maintenance Adjusting the Motion-Control Levers If the motion-control levers do not align horizontally, adjust the right side motion-control lever. 1. Park the machine on a level surface, lower the hopper, engage the parking brake, shut off the engine, and remove the key. 2. Push the motion-control levers down out of the NEUTRAL-LOCK position (Figure 44). 3. Check if the right motion-control lever aligns horizontally with the left motion-control lever (Figure 44). g189559 Figure 42 1.
4. Release the parking brake. 5. Move the motion-control levers forward. Note: The machine should move forward. Note: If the machine does not move forward, refer to Adjusting the Parking Brake (page 33). 6. Engage the parking brake and shut off the machine. Adjusting the Parking Brake g189389 Figure 45 1. Cam 7. 1. Remove the fuel tank; refer to Removing the Fuel Tank (page 27). 2. Inside the left side of the control tower, adjust the nuts until the cables are taught (Figure 46). 2.
Hydraulic System Maintenance WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Fluid injected into the skin must be surgically removed within a few hours by a doctor familiar with this form of injury; otherwise gangrene may result. g203616 Figure 47 • Keep your body and hands away from pinhole leaks or nozzles that eject high-pressure hydraulic fluid. 2. Sight window • Use cardboard or paper to find hydraulic leaks; never use your hands. 5. 1. Expansion-tank cap 3.
2. Shut off the engine, and remove the key. Allow the engine to cool. 3. Lower the cushion and remove the fuel tank; refer to Removing the Fuel Tank (page 27). 4. Remove the 6 bolts (2 rear, 4 side) from the skid plate and remove the skid plate (Figure 49). 10. Loosen the vent plug in each transmission until loose (Figure 51). Note: This allows air to escape the hydraulic system as you add hydraulic fluid. g203517 g203662 Figure 51 Figure 49 1. Rear bolts (2) 1. Vent plug 3. Side bolts (4) 2.
Bleeding the Hydraulic Drive System Servicing the Hydraulic Lift System Bleed the traction hydraulic system whenever you perform maintenance on the hydrostatic transmission or add hydraulic fluid to the expansion tank. Hydraulic-Fluid Specifications Park the machine on a level surface, move the motion-control levers to the NEUTRAL-LOCK position, engage the parking brake, and lower the hopper. Reservoir-tank capacity: 1.4 L (1.5 US quarts) 2. Shut off the engine, and remove the key.
Changing the Hydraulic Fluid for the Lift System Service Interval: Every 300 hours 1. Park the machine on a level surface, move the motion-control levers to the NEUTRAL-LOCK position, engage the parking brake, raise the hopper, and install the cylinder lock. 2. Shut off the machine and remove the key. Allow the machine to cool completely. 3. Remove the filler cap from the reservoir tank (Figure 52).
Replacing the Hydraulic Filter for the Lift System 5. Shut off the engine and check for leaks. 6. Check the fluid level in the reservoir tank, refer to Checking the Hydraulic-Fluid Level for the Lift System (page 36). Service Interval: Every 300 hours Important: Do not substitute an automotive oil Note: Do not overfill the reservoir tank. filter or severe hydraulic system damage may result. 1.
Cleaning Removing Debris from the Machine Service Interval: Before each use or daily Every 100 hours 1. Park the machine on a level surface, move the motion-control levers to the NEUTRAL-LOCK position, engage the parking brake, and lower the hopper. 2. Shut off the engine, and remove the key. Allow the engine to cool. 3. Clean the inside of the hopper using a hose. 4. Clean any debris from under the hopper. 5. Wipe away debris from the air cleaner. 6.
Storage 9. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged. 1. Engage the parking brake, shut off the engine, and remove the key. 10. Paint all scratched or bare metal surfaces. Paint is available from your Authorized Service Dealer. 2. Remove dirt and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine cylinder head fins and blower housing. 11.
Troubleshooting Problem The engine does not start, starts hard, or fails to keep running. The engine loses power. The engine overheats. The machine does not drive. Possible Cause Corrective Action 1. The fuel tank is empty or the shutoff valve is closed. 1. Fill the fuel tank with fuel and open the valve 2. A spark-plug wire is loose or disconnected. 3. A spark plug is pitted, fouled, or the gap is incorrect. 4. The air cleaner is dirty. 5. Dirt is in the fuel filter. 6.
Notes:
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
