Setup Instructions

ManualsBrandsToro ManualsLawn TractorsToro 71252

 2003—The Toro Company

8111 Lyndale Ave., Bloomington, MN 55420, USA

Printed in the USA

Original Instructions (EN)

Wheel Horse

)

Lawn Tractor

For Tractors with 32, and 38, Mowers

Form No. 3351-303 Rev A

Setup Instructions

Loose Parts

Note: Use the chart below to verify that all parts have been shipped.

Description Qty. Use

Front wheels

Shim washers (as required)

Flat washers

Cotter pins

Hub caps

Installing the front wheels

Steering wheel

Spirol pin

Installing the steering wheel

Seat

Knobs

Flat washers

Installing the seat

Bolts—1/4-20 x 3/4 in.

Wing nuts

Installing the battery cables

Spring hook 1 Installing the lift assist spring

Wheels

Wheel bolts

Locknuts—5/16 in.

Installing the anti-scalp wheels

Keys 2 Using in the ignition and Key Choice

switches

Operator’s Manual

Certificate of Conformance

Noise certificate

Reading before operating the tractor

Summary of content (8 pages)

PAGE 1
Wheel Horse) Lawn Tractor Form No. 3351-303 Rev A For Tractors with 32, and 38, Mowers Setup Instructions Loose Parts Note: Use the chart below to verify that all parts have been shipped. Description Qty. Front wheels 2 Shim washers (as required) 2 Flat washers 2 Cotter pins 2 Hub caps 2 Steering wheel 1 Spirol pin 1 Seat 1 Knobs 2 Flat washers 2 Bolts—1/4-20 x 3/4 in. 2 Wing nuts 2 Spring hook 1 Wheels 2 Wheel bolts 2 Locknuts—5/16 in.
PAGE 2
Installing the Front Wheels Installing the Steering Wheel Note: If the wheels are already installed, refer to Checking the Tire Pressure below. 1. Move the front wheels so that they face straight ahead. 2. Slide the steering wheel over the steering shaft and line up the hole in the steering wheel with the hole in the shaft (Fig. 2). 1. Install the shim washers onto the axle. 2. Install the wheel onto the axle with the valve stem facing out. 3. Slide the flat washer onto the axle. 4.
PAGE 3
Installing the Seat Purchase bulk electrolyte with 1.260 specific gravity from a local battery supply outlet. Note: If the seat is already installed, go to Activating the Battery below. Important Never fill the battery with electrolyte while the battery is installed in the tractor. Electrolyte could be spilled on other parts and corrode them. 1. Position the seat onto the seat base by inserting 2 shoulder bolts through the key hole openings at the end of both slots (Fig. 3). 1.
PAGE 4
Installing the Anti-Scalp Wheels 7. Charge the battery for 10 to 15 minutes at 25 to 30 amps or 30 minutes at 4 to 6 amps (Fig. 5). Do not overcharge the battery. For 38, Mowers only 1. Mount the wheels onto the wheel brackets with the wheel bolts and 3/8 in. locknuts (Fig. 6). 4 2 1 3 4 1 2 Figure 5 1. Positive post 2. Negative post 3 m-1505a Figure 6 3. Charger red (+) wire 4. Charger black (–) wire 1. Wheel 2. Wheel bracket Warning 3. Locknut 4.
PAGE 5
Checking the Mower Adjustment Note: The length of the long rod extending out of the front of the adjusting block on the sides of the chassis (Fig. 7) is set to 3/4 in. (19 mm) at the factory. The next time you adjust the front-to-rear blade slope, set the length of long rod that extends out to 5/8 inch (16 mm). For 32, Mowers only The mower was leveled at the factory. However, if the mower is not cutting level, adjust the side-to-side level and the front-to-rear blade slope.
PAGE 6
Purging the Hydro Transaxle 5. Set the parking brake. 6. Stop the engine and wait for all moving parts to stop. For Hydro Drive Tractors only 7. Remove the ignition key. Shipping and handling can introduce air into the hydro transaxle. For proper performance, remove all the trapped air. 8. Raise the right rear wheel off the ground and support it with a jack stand. 1. Move the tractor to a flat, level surface. Note: Ensure that the left rear wheel stays on the ground. 2.
PAGE 7
Checking the Traction Control Pedal 1. If either of the above conditions exist, turn the engine off and ensure that the belt guides are no more than 1/8 inch away from the engine and the transmission pulleys. For Hydro Drive Tractors only 2. Check the cable tension. The cable should be taught and have 1/2 in. (13 mm) movement when you apply a slight pressure to the cable (Fig. 12). You can adjust the traction control pedal for optimum forward and reverse speeds. 1.
PAGE 8