Form No. 3441-790 Rev B Z Master® Professional 7500-D Series Riding Mower With 60in TURBO FORCE® Rear Discharge Mower Model No. 72028—Serial No. 407110000 and Up Model No. 72065—Serial No. 400000000 and Up Register at www.Toro.com.
Introduction It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire. This rotary-blade, riding lawn mower is intended to be used by professional, hired operators.
Contents The safety-alert symbol (Figure 2) appears both in this manual and on the machine to identify important safety messages that you must follow to avoid accidents. This symbol will appear with the word Danger, Warning, or Caution. Safety ....................................................................... 5 General Safety ................................................... 5 Slope Indicator ................................................... 6 Safety and Instructional Decals .....................
Checking the Fuel Lines and Connections.................................................. 39 Electrical System Maintenance ........................... 40 Electrical System Safety ................................... 40 Servicing the Battery......................................... 40 Servicing the Fuses .......................................... 41 Drive System Maintenance .................................. 42 Checking the Seat Belt ..................................... 42 Adjusting the Tracking ............
Safety This machine has been designed in accordance with ANSI standard B71.4-2017. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death. • Read and understand the contents of this Operator’s Manual before starting the engine. • Keep bystanders and children away. • Do not allow children or untrained people to operate or service the machine.
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders away from the battery. 2. No fire, open flame, or smoking 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4.
decal112-9028 112-9028 1. Warning—stay away from moving parts; keep all guards and shields in place. decal116-5988 116-5988 1. Parking brake—engaged 2. Parking brake—disengaged decal107-3069 107-3069 1. Warning–there is no rollover protection when the roll bar is down. 2. To avoid injury or death from a rollover accident, keep the roll bar in the raised and locked position and wear the seat belt. Lower the roll bar only when absolutely necessary; do not wear the seat belt when the roll bar is down. 3.
decal126-8383 126-8383 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
decal126-9278 126-9278 1. Engine—Off 4. Push the bottom of the button to lower the deck. 2. Engine—On 5. Push the top of the button to raise the deck. 3. Engine—Start decal126-9279 126-9279 1. Read the instructions before servicing or performing maintenance to the machine. 2. Time interval 7. Check the jackshaft-fluid level. 8. Grease the deck-drive PTO; refer to the Operator's Manual for further instructions. 9. Check the air cleaner. 3. Check the engine-oil level. 4.
decal135-0328 135-0328 1. Torque the wheel lug nuts to 129 N∙m (95 ft-lb). decal126-9280 126-9280 For Models with 152 cm (60-inch) or 183 cm (72-inch) Decks with Rear Discharge 2. Read and understand the Operator's Manual before performing any maintenance; check the torque after the first 100 hours, then every 500 hours, thereafter. 1. Belt routing decal126-9351 126-9351 1. Chassis (15 A) 3. Main (25 A) 2. Accessory (15 A) 4. Power point (15 A) decal135-0664 135-0664 1.
decal133-8062 133-8062 decal135-0679 135-0679 1. Rotating driveline hazard/entanglement hazard; belt—stay away from moving parts; keep all guards and shields in place. decal135-1432 135-1432 decal135-2837 135-2837 1. Read the Operator’s Manual for more information; Use red Toro wet-clutch transmission fluid; do not use green hydraulic fluid.
Product Overview g227303 Figure 4 1. Height-of-cut pin 7. Motion-control lever 2. Parking-brake lever 8. Fuel-tank cap 9. Anti-scalp roller 3. Monitor/controls 4. Roll bar 5. Engine screen 10. Skid 11. Caster wheel 6. Audible alarm and power point 12.
Controls Become familiar with all the controls before you start the engine and operate the machine. Control Panel g228164 Figure 6 Horizon Display Monitor g225792 Figure 5 1. Horizon display monitor 3. Key switch 2. Deck-lift switch 4. Blade-control switch (power takeoff) 1. Screen 2. LED status light 3. Buttons Information Screen Horizon Display Monitor The information screen displays information relative to machine operation; refer to the Software Guide for more information.
Blade-Control Switch (Power Takeoff) • A fast chirp sound indicates critical errors. • A slow chirping sound indicates less critical errors, such as required maintenance or service intervals. The blade-control switch (PTO) engages and disengages power to the mower blades (Figure 5). Note: During startup, the alarm sounds briefly to verify functionality. The LCD indicator appears on the information screen when the PTO switch is disengaged. Refer to the Software Guide for more information.
Specifications Overall Width 168.2 cm (66.2 inches) Overall Length Roll bar up or down 255.5 cm (100-5/8 inches) Overall Height Roll bar up 182.4 cm (71-13/16 inches) Roll bar down 129.5 cm (51 inches) Overall Height Roll bar up 182.4 cm (71-13/16 inches) Roll bar down 129.5 cm (51 inches) Tread Width of Drive Wheels 112 cm (44-1/8 inches) Tread Width of Caster Wheels (Center-to-Center of Tires) 84 cm (33-1/8 inches) Wheel Base (Center of Caster Tire to Center of Drive Tire) 157.
Fuel Safety Operation • Fuel is extremely flammable and highly explosive. Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety General Safety • Do not allow children or untrained people to operate or service the machine. Local regulations may restrict the age of the operator. The owner is responsible for training all operators and mechanics.
Adding Fuel 5. Fill the fuel tank to the bottom of the filler neck (Figure 7). Note: Do not fill the fuel tank completely full. Recommended Fuel The empty space in the tank allows the fuel to expand. The engine runs on clean, fresh diesel fuel with a minimum cetane rating of 40. Purchase fuel in quantities that can be used within 30 days to ensure fuel freshness. Use summer-grade diesel fuel (No. 2-D) at temperatures above -7°C (20°F) and winter-grade diesel fuel (No. 1-D or No.
Performing Daily Maintenance Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 32). Breaking in a New Machine New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance.
Using the Safety-Interlock System operate as described below, have an Authorized Service Dealer repair the safety system immediately. 1. Sit on the seat, engage the parking brake, and move the blade-control switch (PTO) to the ON position. Try starting the engine; the engine should not start. 2. Sit on the seat, engage the parking brake, and move the blade-control switch (PTO) to the OFF position. Move either motion-control lever out of the NEUTRAL-LOCK position.
Unlatching the Seat During Operation To unlatch the seat, push the seat latch forward (Figure 12). During Operation Safety General Safety • The owner/operator can prevent and is responsible for accidents that may cause personal injury or property damage. • Use your full attention while operating the machine. Do not engage in any activity that causes distractions; otherwise, injury or property damage may occur. g008956 Figure 12 1. Seat latch • Do not operate the machine while ill, tired, or 2.
• Operate the engine only in well-ventilated areas. • • • • • been given rides in the past could appear in the operating area without warning and be run over or backed over by the machine. Exhaust gases contain carbon monoxide, which is lethal if inhaled. Never leave a running machine unattended. Attach towed equipment to the machine only at the hitch point. Do not operate the machine unless all guards and safety devices, such as the deflectors, are in place and functioning properly.
embankments, water, or other hazards. The machine could suddenly roll over if a wheel goes over the edge or the edge collapses. Keep a safe distance (twice the width of the machine) between the machine and any hazard. Use a walk-behind machine or a hand trimmer to mow the grass in these areas. Operating the Parking Brake • Avoid starting, stopping, or turning the machine on Engaging the Parking Brake Always engage the parking brake when you stop the machine or leave it unattended. slopes.
Operating the Mower Starting the Engine Blade-Control Switch (PTO) Important: Do not engage the starter for more than 5 seconds at a time. If the engine fails to start, wait 15 seconds between attempts. Failure to follow these instructions can burn out the starter motor. The blade-control switch (PTO) starts and stops the mower blades and any powered attachments.
Shutting Off the Engine Using the Motion-Control Levers CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Always remove the key and engage the parking brake when leaving the machine unattended. g004532 Figure 22 1. Motion-control levers—NEUTRAL-LOCK position 4. Reverse 2. Center, unlocked position 5. Front of the machine 3.
Driving the Machine The drive wheels turn independently, powered by hydraulic motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing the machine to spin rather than turn. This greatly improves the machine maneuverability but may require some time for you to adapt to how it moves. The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the FAST position for best performance.
Adjusting the Height of Cut Adjusting the Anti-Scalp Rollers Adjust the height of cut from 25 to 140 mm (1 to 5-1/2 inches) in 6 mm (1/4 inch) increments by moving the clevis pin into different hole locations. 1. With the engine running, push the deck-lift switch rearward until the mower deck is fully raised, and release the switch immediately. 2. Rotate the height-of-cut pin until the roll pin in it lines up with the slots in the holes in the height-of-cut bracket and remove it (Figure 25). 3. 4.
Adjusting the Skids Mount the skids in the lower position when operating at heights of cut greater than 51 mm (2 inches) and in a higher position when operating at heights of cut lower than 51 mm (2 inches). Adjust the skids as shown in Figure 28. g227783 Figure 27 1. Bolt 3. Anti-scalp roller 2. Bushing 4. Flange nut 5. Torque the flange nut to 41 to 47 N∙m (30 to 35 ft-lb).
Operating Tips drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward. Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower deck in uncut grass.
Transporting the Machine After Operation Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.
1. If using a trailer, connect it to the towing vehicle and connect the safety chains. 2. If applicable, connect the trailer brakes and lights. 3. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 30). 4. Back the machine up the ramp (Figure 31). g028043 Figure 31 1. Back the machine up the ramp. 2. Drive the machine forward down the ramp. 5. Shut off the engine, remove the key, and engage the parking brake. 6.
Maintenance • Check the parking brake operation frequently. Maintenance Safety • Never tamper with safety devices. Check their • If you leave the key in the switch, someone could • Clean grass and debris from the cutting unit, Adjust and service it as required. proper operation regularly. accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. muffler, drives, and engine compartment to prevent fires.
Maintenance Service Interval Maintenance Procedure • • • • Every 400 hours • • • • • Grease the deck-idler pivots. Grease the caster pivots (more often in dirty or dusty conditions). Service the air cleaner (More frequently in extremely dusty or dirty conditions). Change the engine oil and filter if using Toro Premium Engine Oil (API classification CK-4 or higher) (more often in dirty or dusty conditions).
Lubrication Greasing the Machine Service Interval: Every 400 hours/Yearly (whichever comes first)—Grease the deck-idler pivots. Yearly—Grease the deck drive PTO. Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: No. 2 lithium or molybdenum grease 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2.
Greasing the Caster Pivots 6. Service Interval: Every 400 hours/Yearly (whichever comes first) (more often in dirty or dusty conditions). Yearly—Repack the caster-wheel bearings (more often in dirty or dusty conditions). 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
Engine Maintenance Servicing the Air Cleaner Note: If the foam gasket in the cover is damaged, replace it. Engine Safety Important: Avoid using high-pressure air, which could force dirt through the filter into the intake tract. • Keep your hands, feet, face, clothing, and other body parts away from the muffler and other hot surfaces. Allow engine components to cool before performing maintenance. Important: Do not clean the used filter to avoid damaging the filter media.
Servicing the Engine Oil 3. Open the hood. Service Interval: Before each use or daily After the first 200 hours—Change the engine oil and filter. Every 200 hours—Change the engine oil and filter if not using Toro Premium Engine Oil, but any oil meeting API classification CJ-4 or higher or as stated in Engine-Oil Specifications. Every 400 hours—Change the engine oil and filter if using Toro Premium Engine Oil (API classification CK-4 or higher) (more often in dirty or dusty conditions).
Changing the Engine Oil and Filter If possible, run the engine just before changing the oil because warm oil flows better and carries more contaminants than cold oil. 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Open the hood. 4. Change the engine oil as shown in Figure 38. g027477 Figure 39 g031623 Figure 38 6.
Replacing the Water Separator Fuel System Maintenance Service Interval: Every 400 hours—Replace the fuel-filter canister for the water separator (more often in dirty and dusty conditions). DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Refer to Fuel Safety (page 17) for a complete list of fuel related precautions.
Electrical System Maintenance WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Electrical System Safety • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last.
Installing the Battery Note: Do not run the machine with the battery disconnected, electrical damage may occur. Note: Position the battery in the tray with the terminal posts opposite from the hydraulic tank. g000960 Figure 44 1. Positive battery post 3. Red (+) charger lead 2. Negative battery post 4. Black (-) charger lead Servicing the Fuses The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check component/circuit for malfunction or short.
Drive System Maintenance 9. Align the levers in the front-to-rear position by bringing the levers together to the NEUTRAL position, and slide them until they are aligned, then tighten the bolts (Figure 47). Checking the Seat Belt Service Interval: Before each use or daily Inspect the seat belt for wear, cuts, and proper operation of the retractor and buckle. Replace the seat belt if it is damaged. Adjusting the Tracking 1. 2. 3. 4. 5. 6. 7. 8. Disengage the blade-control switch (PTO).
Adjusting the Caster-Pivot Bearing Checking the Tire Pressure Service Interval: Every 50 hours/Monthly (whichever comes first) Service Interval: Every 500 hours/Yearly (whichever comes first) Rear tire air pressure specification: 124 kPa (18 psi). 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Low tire pressure decreases machine side-hill stability. This could cause a rollover, which may result in personal injury or death.
Changing the Gearbox Oil Servicing the Gearbox Service Interval: After the first 200 hours Checking the Gearbox-Oil Level Every 400 hours Service Interval: Every 50 hours If the oil becomes contaminated, contact your Toro Distributor because the system must be flushed. Contaminated oil looks milky or black when compared to clean oil. Use SAE 75W-90 synthetic gear lube. 1. Park the machine on a level surface and engage the parking brake. 2. Lower the mower deck to the 25 mm (1 inch) height of cut.
Cooling System Maintenance Cooling System Safety • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. – Always allow the engine to cool at least 15 minutes before removing the radiator cap. g227787 Figure 52 – Use a rag when opening the radiator cap, and open the cap slowly to allow steam to escape. 1. Expansion-tank cap 3. Add line 2.
Note: If debris remains, repeat until clean. 9. 7. Lower the hood. 8. Start the engine to ensure that the fan functions properly. As air purges from the engine block and the coolant level drops, add additional coolant to the radiator. Changing the Engine Coolant 10. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
Brake Maintenance Adjusting the Parking Brake Service Interval: After the first 100 hours Every 400 hours Check to ensure that parking brake is adjusted properly. Follow this procedure also whenever you have removed or replaced a brake component. 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
13. Belt Maintenance Repeat steps 10 through 12 until a visible gap is achieved and the wheel hub rotates freely. Repeat this procedure for the other side. Inspecting the Belts Note: The brake should fully disengage when the brake is in the released position. 14. Rotate the drive wheel release handle to the operating position; refer to Using the Drive-Wheel Release Valves (page 30). 15. Install the rear tires and torque the lug nuts to 115 to 142 N∙m (85 to 105 ft-lb). 16. Remove the jack stands.
Controls System Maintenance square hole, install the belt around the idler pulley (Figure 55). 9. Install the belt covers. Checking the Alternator-Belt Tension Adjusting the Control-Handle Position Service Interval: Every 100 hours There are 2 height positions for the control levers—high and low. Remove the bolts to adjust the height for the operator. 1. Apply 44 N (10 lb) of force to the alternator belt, midway between the pulleys. 2.
4. Raise the rear of the machine up and support it with jack stands (or equivalent support) just high enough to allow the drive wheels to turn freely. 5. Remove the electrical connection from the seat safety switch, located under the bottom cushion of the seat. Note: The switch is a part of the seat assembly. 6. Temporarily install a jumper wire across the terminals in the connector of the main wire harness. 7. Start the engine, run it at full throttle, and disengage the parking brake.
Hydraulic System Maintenance Note: The wheels should stop turning or slightly creep in reverse. 12. Shut off the machine. 13. Remove the jumper wire from the wire harness and plug the connector into the seat switch. 14. Remove the jack stands. 15. Raise the deck and install the height-of-cut pin. 16. Check and ensure that the machine does not creep in neutral with the parking brake disengaged.
2. Move the motion-control levers to the NEUTRAL-LOCK position and start the engine. 8. Note: Run the engine at the lowest possible 9. Replace the dipstick and thread the fill cap finger-tight onto the filler neck. Check all hoses and fittings for leaks. rpm to purge any air in the system. Changing the Hydraulic Fluid and Filter Important: Do not engage the PTO. 3. Raise the deck to extend the lift cylinders, shut off the engine, and remove the key. 4.
6. Clean the area around the hydraulic-fluid filter and remove the filter (Figure 63). 7. Install a new hydraulic-fluid filter and turn the filter clockwise until the rubber seal contacts the filter adapter, then tighten the filter an additional 2/3 to 3/4 turn. 8. 9. Mower Deck Maintenance Blade Safety Install the 4 drain plugs. • Inspect the blades periodically for wear or damage. Note: The wheel motor drain plugs are magnetic; wipe them clean before installing.
g006530 Figure 65 1. Cutting edge 3. Wear/slot forming 2. Curved area 4. Crack g014973 Figure 67 1. Blade (in position for measuring) Checking for Bent Blades 2. Level surface 3. Measured distance between blade and the surface (A) Note: The machine must be on a level surface for the following procedure. 4. 1. Raise the mower deck to the highest height-of-cut position. 2.
g014973 Figure 69 1. Opposite blade edge (in position for measuring) 2. Level surface 3. Second measured distance between blade and surface (B) A. If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade with a new blade; refer to Removing the Blades (page 55) and Installing the Blades (page 56). g295816 Figure 70 Note: If a bent blade is replaced with a new blade, and the dimension obtained continues to exceed 3 mm (1/8 inch), the blade spindle could be bent.
g000553 3. Apply copper-based lubricant or grease to the threads of the blade bolt as needed to prevent seizing. Install the blade bolt finger-tight. 4. Place a wrench on the flat of the spindle shaft and torque the blade bolt to 75 to 81 N∙m (55 to 60 ft-lb). Figure 72 1. Blade 3. 2. Balancer Leveling the Mower Deck Repeat this procedure until the blade is balanced. Note: Ensure that the mower deck is level before matching the height of cut (HOC). Installing the Blades 1.
g009997 Figure 76 1. 76 mm (3 inches) 4. 76 mm (3 inches) 2. Rear blade tip 5. Level surface g231991 Figure 77 3. Front blade tip 1. Deck adjustment 8. Fine-tune the adjustment nut on the front deck lift assembly by turning it (Figure 77). 2. Jam nut Note: To increase the height, turn the 9. 3. Adjustment nut adjustment nut clockwise; to decrease, turn it counterclockwise. Measure the rear blade tip height.
adjustment bolt by rotating it counterclockwise (Figure 80). Note: Loosen or tighten the single-point adjustment bolt enough to move the height-of-cut plate mounting bolts at least 1/3 the length of the available travel in their slots. This regains some up and down adjustment on each of the 4 deck links. g232012 Figure 78 1. Single-point height adjustment bolt 3. Rear height-of-cut plate mounting bolt 2. Front height-of-cut plate mounting bolt g009042 12.
Cleaning Cleaning the Engine and Exhaust System Area Service Interval: Before each use or daily—Clean the engine and exhaust system area. Important: Do not use water to clean the engine. Use low-pressure compressed air. See the engine owner's manual. 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
Storage 12. Check the condition of the blades; refer to Servicing the Cutting Blades (page 53). Storage Safety 13. Prepare the machine for storage when non-use occurs over 30 days. Prepare the machine for storage as follows: • Shut off the engine, remove the key, and wait for all moving parts to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it. A.
Troubleshooting Problem The starter does not crank. The engine does not start, starts hard, or fails to keep running. Possible Cause 1. The blade-control switch is engaged. 1. Disengage the blade-control switch. 2. The parking brake is disengaged. 3. The motion-control levers are not in the NEUTRAL-LOCK position. 4. You are not sitting in the operator’s seat. 5. The battery is dead. 6. The electrical connections are corroded or loose. 7. A fuse is blown. 8. A relay or switch is damaged. 2.
Problem The machine does not drive. The machine vibrates abnormally. The cutting height is uneven. Possible Cause 1. The bypass valves are not closed tight. 1. Tighten the bypass valves. 2. The pump belt is worn, loose, or broken. 3. The pump belt is off a pulley. 4. The idler spring is broken or missing. 5. The hydraulic fluid level is low or too hot. 2. Change the belt. 3. Change the belt. 4. Replace the spring. 5. Add hydraulic fluid to the reservoirs or let it cool down. 1.
Electrical Schematic—Machine with Horizon Display Monitor (Rev.
J02 B+ @ BATTERY 1 CLAMP J01 OIL PRESSURE 1 SWITCH P03 STARTER A B B+ C RED RED RED RED BROWN YELLOW ORANGE WHITE BLUE BROWN RED YELLOW VIOLET SP06 SP02 2 1 P04 AIR FILTER SW RED/WHITE GRAY/BROWN P02 7 RED 26 GREEN 25 BLACK 8 RED 37 BLUE 52 BLACK 39 VIOLET 54 ORANGE 38 BLACK 11 BLUE 51 BROWN 20 BLUE 19 YELLOW 29 50 28 60 59 YELLOW 34 12 30 48 18 47 17 33 16 4 5 SP12 ALTERNATOR J03 1 P05 1 2 B IG YELLOW YELLOW VIOLET VIOLET WHITE P24 1 2 3 4 5 6 7 8 9 10 11 12 ORANGE 5VS PRAIL ANALOG GND 5VS
BATTERY CLAMP J02 1 B+ A STARTER P03 B B+ C OIL TEMP P21 1 SENSOR 2 ENGINE SPEED P13 1 2 SENSOR 6 5 4 RACK P02 ACT 3 2 1 RED RED/GREEN RED/GREEN BLACK BLACK BLACK SP11 J03 BLACK RED/GREEN ALTERNATOR 1 P05 1 2 B IG L BLUE/GREEN RED/GREEN BLACK ORANGE SP2 SP1 SP9 BLUE/RED BLACK TO CONNECTOR P06 ON HARNESS 1 2 1 1 2 P07 1 2 4 9 5 3 8 6 12 7 10 11 J01 P04 P06 OIL FUEL AIR FILTER PRESSURE PUMP SW SW BLACK RED/WHITE SP7 P09 SP10 BLUE/RED BLUE/YELLOW SP6 FLY BACK DIODE P16 A B 1 2 3
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
