Setup Instructions

ManualsBrandsToro ManualsRiding ProductsZ Master Professional 7500-D Series Riding Mower, With 72in TURBO FORCE Side Discharge Mower

FormNo.3448-442RevA

ZMaster

Professional7500-DSeriesRidingMower

With60inor72inTURBOFORCE

SideDischargeMower

ModelNo.72027—SerialNo.400000000andUp

ModelNo.72030—SerialNo.400000000andUp

ModelNo.72076—SerialNo.409800000andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Checkthehydraulic-uidlevel.

Nopartsrequired

–

Checkthedeckgearbox-uidlevel.

Nopartsrequired

–

Checkthewheellugnuttorque.

J-bolt2

Wingnut2

Hold-downclamp1

Installthebattery.

Nopartsrequired

–

Raisetherolloverprotectionsystem

(ROPS).

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer(Allmachines).

Operator'sManual

Engineowner'smanual1

Registrationcard1

Operatortrainingmaterial

Key2

Deliveringthemachinetothecustomer.

8111LyndaleAvenueSouth

Bloomington,MN55420Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3448-442*

Summary of content (8 pages)

PAGE 1
Form No. 3448-442 Rev A Z Master® Professional 7500-D Series Riding Mower With 60in or 72in TURBO FORCE® Side Discharge Mower Model No. 72027—Serial No. 400000000 and Up Model No. 72030—Serial No. 400000000 and Up Model No. 72076—Serial No. 409800000 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Add fuel to the machine. No parts required – Check the engine-oil level.
PAGE 2
1 4 Adding Fuel to the Machine Checking the Hydraulic-Fluid Level No Parts Required No Parts Required Procedure Procedure Add fuel to the machine before starting it. Refer to your Operator’s Manual for the correct fuel and procedure. 2 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Move the motion-control levers to the NEUTRAL-LOCK position and start the engine.
PAGE 3
g228816 Figure 2 1. Full line 2. Add line g231764 Figure 3 8. Replace the dipstick and thread the fill cap finger-tight onto the filler neck. 9. Check all hoses and fittings for leaks. 1. Dipstick/fill plug 7. 5 If the fluid level is low, add fluid until the level is between the marks on the dipstick. Important: Do not overfill the gearbox; overfilling the gearbox may damage it. Checking the Deck Gearbox-Fluid Level 6 Checking the Wheel Lug Nut Torque No Parts Required Procedure 1.
PAGE 4
7 8 Installing the Battery Raising the Rollover Protection System (ROPS) Parts needed for this procedure: 2 J-bolt 2 Wing nut 1 Hold-down clamp No Parts Required Procedure 1. Pull the knob and rotate 90° to the unlatched position (Figure 4). 2. Raise the roll bar to the operate position, and rotate the knobs so that they move partially into the grooves (Figure 4). 3.
PAGE 5
g008619 Figure 5 1. Engaged position 2. Partially engaged—do not operate the machine with the roll back in this position.
PAGE 6
9 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the machine. Check that all spindles are greased. Check the engine-oil level.
PAGE 7
10 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator's Manual 1 Engine owner's manual 1 Registration card 1 Operator training material 2 Key Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No. Serial No.
PAGE 8
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank • Oil fill cap/Oil dipstick • Engine-oil filter • Engine-oil drain • Fuel gauge, valve and hose • Air filter • Radiator coolant (if applicable) • Hydraulic-fluid reservoir • Hydraulic filter • Battery • Key switch • Throttle lever • Choke (if applicable) • Power take off switch (PTO) • Motion-control levers • Parking brake • Height o