Software Guide

ManualsBrandsToro ManualsRiding ProductsZ Master Professional 5000 Series Riding Mower, with 60in TURBO FORCE Side Discharge Mower

FormNo.3433-925RevC

ZMaster

Professional5000or6000SeriesRiding

Mower

with48in,52in,60in,or72inTURBOFORCE

Mower

ModelNo.72904—SerialNo.400000000andUp

ModelNo.72906—SerialNo.400000000andUp

ModelNo.72911—SerialNo.400000000andUp

ModelNo.72912—SerialNo.400000000andUp

ModelNo.72915—SerialNo.400000000andUp

ModelNo.72918—SerialNo.400000000andUp

ModelNo.72921—SerialNo.400000000andUp

ModelNo.72922—SerialNo.400000000andUp

ModelNo.72926—SerialNo.400000000andUp

ModelNo.72928—SerialNo.400000000andUp

ModelNo.72930—SerialNo.400000000andUp

ModelNo.72943—SerialNo.400000000andUp

ModelNo.72945—SerialNo.400000000andUp

ModelNo.72951—SerialNo.400000000andUp

ModelNo.72955—SerialNo.400000000andUp

ModelNo.72980—SerialNo.400000000andUp

ModelNo.72982—SerialNo.400000000andUp

SoftwareGuide

Readthisinformationcarefullytolearnhowtooperateandmaintainyourproductproperlyandtoavoidinjury

andproductdamage.Youareresponsibleforoperatingtheproductproperlyandsafely.ReadyourOperator’s

Manualformoreinformation.

Thehourmetermonitorsenginetemperature,oilpressure,andtheoverallelectricalsystem.Italsodisplays

machinehours,safety-interlockstatus,fuellevel,andmaintenancereminders.

8111LyndaleAvenueSouth

Bloomington,MN55420Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3433-925*

Summary of content (12 pages)

PAGE 1
Form No. 3433-925 Rev C Master® Z Mower Professional 5000 or 6000 Series Riding with 48in, 52in, 60in, or 72in TURBO FORCE® Mower Model No. 72904—Serial No. 400000000 and Up Model No. 72906—Serial No. 400000000 and Up Model No. 72911—Serial No. 400000000 and Up Model No. 72912—Serial No. 400000000 and Up Model No. 72915—Serial No. 400000000 and Up Model No. 72918—Serial No. 400000000 and Up Model No. 72921—Serial No. 400000000 and Up Model No. 72922—Serial No. 400000000 and Up Model No. 72926—Serial No.
PAGE 2
Screen Icons The screen uses the following icons: PTO Operator Presence Control (OPC) Parking Brake Battery Voltage Neutral Lock Fuel Level Hour Meter Transmission-Fluid Maintenance Engine-Oil Maintenance Check Engine Error Voltage Error Power to Run Error Low Engine-Oil Pressure Error Clutch Error Clutch Reset Required Check Fault Error 2
PAGE 3
Product Overview Controls Information Screen The information screen displays icons and information relative to machine operation. LED Status Light The LED is multi-colored to indicate the system status and is located on the right side of the panel. • Solid Green—indicates normal operating activity. • Blinking Red—indicates a fault is active. g031090 • Blinking Green and Orange—indicates a clutch Figure 1 Models with Fuel Sender reset is required. • Solid Red—indicates maintenance is required. 1.
PAGE 4
g030964 Figure 3 Startup Screen 1. Firmware version 2. PTO hours 3. Battery voltage 4. Hours until engine-oil maintenance is required 5.
PAGE 5
PTO Hour Meter Screen Hour Meter Screen This displays the number of hours that the PTO has been engaged (Figure 4). The hour meter records hours when the hour meter symbol flashes. Hours display when the machine is off or when the machine is running. The display turns off after 5 minutes. g222036 Figure 4 g031198 Figure 7 Hour meter without a fuel sender Battery Voltage Screen This screen displays the current battery voltage (Figure 5).
PAGE 6
Default Screen After the startup screens display, the default screen displays (Figure 8). The safety-interlock indicators illuminate when each control meets the SAFE TO START mode (PTO disengaged, parking brake engaged, motion-control levers in the NEUTRAL-LOCK position, and operator present). g037702 Figure 9 1. Safety-interlock indicators 2. Hour meter g030961 Figure 8 1. Safety-interlock indicators 2. Hour meter 3.
PAGE 7
Maintenance Reminders and Alerts There are 2 maintenance reminders: • Service Engine The engine oil service reminder counts down from the initial break-in service interval of 5 engine hours and then counts down from 100 hours for each service interval thereafter. The hour meter displays the number of engine hours until either the engine oil or transmission-fluid maintenance is due. The reminder flashes and the LED displays a solid, red light. An alert occurs when the hour counter has reached zero.
PAGE 8
Alerts and Error Messages Manually Resetting Maintenance Reminders The system is capable of displaying the following errors: • Voltage Error To access the Service Engine screen you must sit in the operator’s seat, disengage the blade-control switch (PTO), move the motion-control levers to the NEUTRAL-LOCK position, and engage the parking brake. When the key-run voltage is less than 12.3 V or greater than 16 V, a voltage error flashes. The LED flashes a red light.
PAGE 9
• Engine Over Temperature Error • Clutch Open Error If the clutch output disconnects, the number “6” displays in the lower, left corner of the screen. The LED flashes a red light. This occurs if an engine over temperature is detected. Check the engine oil and clean debris from the engine. The LED flashes a red light and the clutch disengages.
PAGE 10
• Check-Engine Error If an engine fault occurs, the system displays the Check Engine alert and flashes a red light. To retrieve the specific fault(s), follow the key cycle procedure provided in the engine owner’s manual. If more than 1 error occurs, the display alternates between codes. In order to display the diagnostic codes, you must cycle the key switch 2 times between the ON and OFF positions, then to the ON position, but do not start the engine.
PAGE 11
Notes:
PAGE 12