Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 73471

The Toro Company – 1999

Printed in USA

Form No. 3323-484

Setup

Instructions

Model Numbers 73471, 73542,

and 73561—200000001 & Up

518xi, 520xi & 522xi Tractor

Loose Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Seat Assembly

Shoulder Bolt – 5/16”

Locknut – 5/16”

Installing the seat

Steering Wheel

Boot Washer

Nut

Lock Washer

Trim Cover

Installing the steering wheel

Bolt – 1/4”-20 x .88” Long

Washer – 1/4”

Hex Nut – 1/4”-20

Attaching the battery cables

Hitch Pin

Hairpin Cotter

Flat Washer – .50” I.D.

Installing the drawbar hitch pin

Key 2 Use in ignition and “Key Choice” switches

Operator’s Manual

Engine Operator’s Manual

Riding Mower Safety Video

Read before operating the tractor

Watch before operating the tractor

Installing the Seat

1. Mount the seat to the seat base using two 5/16”

shoulder bolts and lock nuts (Fig. 1).

2. Insert the seat switch wire through the center

opening in the seat base (Fig 1).

3. Push the seat switch wire connector into the wire

harness connector.

Summary of content (8 pages)

PAGE 1
Form No. 3323-484 518xi, 520xi & 522xi Tractor Model Numbers 73471, 73542, and 73561—200000001 & Up Setup Instructions Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Seat Assembly 1 Shoulder Bolt – 5/16” 2 Locknut – 5/16” 2 Steering Wheel 1 Boot Washer 1 Nut 1 Lock Washer 1 Trim Cover 1 Bolt – 1/4”-20 x .88” Long 2 Washer – 1/4” 2 Hex Nut – 1/4”-20 2 Hitch Pin 1 Hairpin Cotter 1 Flat Washer – .50” I.D.
PAGE 2
Set-Up Instructions 4. Secure the steering wheel to the shaft with a lock washer and nut (Fig. 2). Tighten the retaining nut to 45–50 ft–lbs. 5. Install the trim cover on the steering wheel. 3 1 6 5 4 3 5 2 4 6 m–3453 Figure 1 1. 2. 3. 4. Seat Seat base 5/16” shoulder bolt (2) 5/16” Locknut (4) 1 5. Seat switch wire connector 6. Opening for seat switch wire 2 m–2482 Figure 2 Installing the Steering Wheel 1. Install the boot washer onto the steering shaft (Fig. 2). 2.
PAGE 3
Set-Up Instructions Check to Insure that Steering Linkage is Centered 1. With the tractor on a level surface, turn the steering wheel fully to the left and check the clearance of the left hand spindle stop to the stop on the front axle. There should be a slight clearance between the stops (Fig. 3). Checking Tire Pressure Check front and rear tire pressure. The correct front and rear tire pressure is 20 psi (138 kPa).
PAGE 4
Set-Up Instructions 1 4 2 3 1 2 3 1262 Figure 4 1. Filler caps 2. Electrolyte 3. Lower part of tube 1254 Figure 5 1. Positive battery post 2. Negative battery post POTENTIAL HAZARD • Charging battery produces gasses. 5. Slowly pour electrolyte into each cell until the level is once again up to “UPPER” line on the battery case (Fig. 4), then install the filler caps. 6.
PAGE 5
Set-Up Instructions Note: 2 There must be a PTO driven attachment installed to provide a load in order to burnish the clutch facings properly. 1. Run the engine at full throttle and engage the clutch bringing the load to full speed. Then disengage the clutch. 1 2. Let the load come to a full stop, then engage again. 3 3. Repeat these procedures (1 and 2) 5 times. 4 m–2481 Figure 6 1. Drawbar hitch pin 2. Drawbar hitch 3. .50” Flat washer 4. Hairpin cotter Test Driving the Tractor 1.
PAGE 6
Set-Up Instructions 5. 6. As applicable, check and test the operation of the following: • Engine, choke and throttle controls • Gauges • Headlights and taillights • Indicator lights • PTO clutch and brake • Lift system • Service and parking brakes • Transmission controls • Steering • Tractor operation in forward and reverse Test the operation of the safety interlock system (refer to the tractor Operator’s Manual for the correct procedure).
PAGE 7
PAGE 8