Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 73552



The T

oro Company – 1999

Printed in USA

FORM NO. 3321–970

SET UP

INSTRUCTIONS

MODEL NO. 73552–9900001 & UP

523Dxi GARDEN TRACTOR

Loose

Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Steering Wheel

Boot W

asher

Nut

Lock W

asher

rim Cover

Installing the steering wheel

Seat Assembly

Shoulder Bolt – 5/16”

Locknut – 5/16”

Installing the seat

Hitch Pin

Hairpin Cotter

Flat W

asher – .50” I.D.

Installing the drawbar hitch pin

Key 2

Use in ignition and “Key Choice” switches

Operator’

s Manual

Engine Operator

’

s Manual

Riding Mower Safety V

ideo

Read before operating the tractor

Attach to the tractor

“Thank Y

ou” Card

1 Read

Summary of content (8 pages)

PAGE 1
FORM NO. 3321–970 523Dxi GARDEN TRACTOR MODEL NO. 73552–9900001 & UP SET UP INSTRUCTIONS Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Steering Wheel 1 Boot Washer 1 Nut 1 Lock Washer 1 Trim Cover 1 Seat Assembly 1 Shoulder Bolt – 5/16” 2 Locknut – 5/16” 2 Hitch Pin 1 Hairpin Cotter 1 Flat Washer – .50” I.D.
PAGE 2
Set-Up Instructions Installing the Seat Note: 1. Mount the seat to the seat base using two 5/16” shoulder bolts and lock nuts (Fig. 1). 2. Insert the seat switch wire through the center opening in the seat base (Fig 1). 3. There is no fixed straight ahead position on power steering models. 4. Secure the steering wheel to the shaft with a lock washer and nut (Fig. 2). Tighten the retaining nut to 45–50 ft–lbs. 5. Install the trim cover on the steering wheel.
PAGE 3
Set-Up Instructions Check to Insure that Steering Linkage is Centered 1. Activating the Battery With the tractor on a level surface, turn the steering wheel fully to the left and check the clearance of the left hand spindle stop to the stop on the front axle. There should be a slight clearance between the stops (Fig. 3). POTENTIAL HAZARD • Battery electrolyte contains sulfuric acid which is a deadly poison and it causes severe burns.
PAGE 4
Set-Up Instructions 4. When the battery is fully charged, unplug the charger from electrical outlet, then disconnect the charger leads from the battery posts (Fig. 5). 4 2 2 3 1 1 3 m–3799 Figure 4 1. Cell cover 2. Electrolyte 3. Lower part of tube m–3798 Figure 5 POTENTIAL HAZARD • Charging battery produces gasses. WHAT CAN HAPPEN • Battery gasses can explode. 1. Positive battery post 2. Negative battery post 5.
PAGE 5
Set-Up Instructions Installing the Drawbar Hitch Pin Burnishing the Clutch Insert the drawbar hitch pin into the drawbar hitch and secure it with a .50” I.D. flat washer and hairpin cotter (Fig. 6). The following break–in procedure must be performed as part of predelivery service or when a new clutch is installed. Note: 1. Run the engine at full throttle and engage the clutch bringing the load to full speed. Then disengage the clutch. 2. Let the load come to a full stop, then engage again. 3.
PAGE 6
Set-Up Instructions Test Driving the Tractor 1. 2. 3. 4. 5. 6. 7. As applicable, check and test the operation of the following: Check the oil level in the crankcase (refer to Engine Oil in your tractor Operator’s Manual for oil type, viscosity and crankcase capacity). • Engine and throttle controls • Gauges Check the oil level in the transaxle (refer to Transaxle Fluid in your tractor Operator’s Manual for oil type, viscosity and capacity).
PAGE 7
PAGE 8