Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 73561



The T

oro Company – 1998

Printed in USA

FORM NO. 3321–962

SET UP

INSTRUCTIONS

MODEL NO. 73471–9900001 & UP

MODEL NO. 73542–9900001 & UP

MODEL NO. 73561–9900001 & UP

518xi, 520xi & 522xi GARDEN TRACTOR

Loose

Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Seat Assembly

Shoulder Bolt – 5/16”

Locknut – 5/16”

Installing the seat

Steering Wheel

Boot W

asher

Nut

Lock W

asher

rim Cover

Installing the steering wheel

Bolt – 1/4”-20 x .88” Long

asher – 1/4”

Hex Nut – 1/4”-20

Attaching the battery cables

Hitch Pin

Hairpin Cotter

Flat W

asher – .50” I.D.

Installing the drawbar hitch pin

Key 2

Use in ignition and “Key Choice” switches

Operator’

s Manual

Engine Operator

’

s Manual

Riding Mower Safety V

ideo

Read before operating the tractor

Attach to the tractor

Thank Y

ou Card

1 Read

Summary of content (8 pages)

PAGE 1
FORM NO. 3321–962 518xi, 520xi & 522xi GARDEN TRACTOR MODEL NO. 73471–9900001 & UP MODEL NO. 73542–9900001 & UP MODEL NO. 73561–9900001 & UP SET UP INSTRUCTIONS Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Seat Assembly 1 Shoulder Bolt – 5/16” 2 Locknut – 5/16” 2 Steering Wheel 1 Boot Washer 1 Nut 1 Lock Washer 1 Trim Cover 1 Bolt – 1/4”-20 x .88” Long 2 Washer – 1/4” 2 Hex Nut – 1/4”-20 2 Hitch Pin 1 Hairpin Cotter 1 Flat Washer – .
PAGE 2
Set-Up Instructions Installing the Seat 1. Mount the seat to the seat base using two 5/16” shoulder bolts and lock nuts (Fig. 1). 2. Insert the seat switch wire through the center opening in the seat base (Fig 1). 3. Push the seat switch wire connector into the wire harness connector. 3 1 5 2 4 6 m–3453 Figure 1 1. 2. 3. 4. 2 Seat Seat base 5/16” shoulder bolt (2) 5/16” Locknut (4) 5. Seat switch wire connector 6.
PAGE 3
Set-Up Instructions Installing the Steering Wheel 1. Install the boot washer onto the steering shaft (Fig. 2). 2. Remove the plastic trim cover from the steering wheel (Fig. 2) 3. Install the steering wheel onto the shaft, carefully aligning the splines (Fig. 2). Note: Check to Insure that Steering Linkage is Centered 1. With the tractor on a level surface, turn the steering wheel fully to the left and check the clearance of the left hand spindle stop to the stop on the front axle.
PAGE 4
Set-Up Instructions Checking Front Wheel Toe–In 2. With the tractor on a level surface, check to make sure the front wheel toe-in is between 1/8” and 1/4”. For instructions on adjusting toe-in, refer to the Maintenance section in Operator’s Manual. Remove the filler caps from the battery. Slowly pour electrolyte into each cell until the electrolyte level is up to the lower part of the tube (Fig. 4). Use an electrolyte with a specific gravity of 1.265.
PAGE 5
Set-Up Instructions 4 2 3 1 1 2 3 4 m–2481 Figure 6 1254 Figure 5 1. Positive battery post 2. Negative battery post 5. 6. 1. Drawbar hitch pin 2. Drawbar hitch 3. Red (+) charger lead 4. Black (–) charger lead Slowly pour electrolyte into each cell until the level is once again up to “UPPER” line on the battery case (Fig. 4), then install the filler caps. Checking the Wiring and Fasteners • Inspect the tractor for any loose electrical connections and secure them as required.
PAGE 6
Set-Up Instructions Burnishing the Clutch 5. The following break–in procedure must be performed as part of pre–delivery service or when a new clutch is installed. As applicable, check and test the operation of the following: • Engine, choke and throttle controls • Gauges • Headlights and taillights • Indicator lights • PTO clutch and brake Run the engine at full throttle and engage the clutch bringing the load to full speed. Then disengage the clutch.
PAGE 7
PAGE 8