Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 74134

FormNo.3381-538RevA

GuardKit

TimeCutter

RidingMowerwith81cmor127cmCuttingUnit

ModelNo.74130

ModelNo.74134

InstallationInstructions

Donotsupplytheseinstructionstothecustomer.

Theseinstructionsareforadealertoinstalladditionalbelt

guardsonunitssoldinFrance.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

110-6691

Model74130only

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

114-1606

Model74130only

1.Entanglementhazard,belt—keepallguardsinplace.

120-1119

1.Firehazard—readtheOperator'sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3381-538*A

Summary of content (4 pages)

PAGE 1
Form No. 3381-538 Rev A Guard Kit TimeCutter® Riding Mower with 81cm or 127cm Cutting Unit Model No. 74130 Model No. 74134 Installation Instructions Do not supply these instructions to the customer. These instructions are for a dealer to install additional belt guards on units sold in France. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
1 Preparing for Installation No Parts Required Procedure Important: Refer to the Operator’s Manual if you are unfamiliar with the specifics of operating this machine before proceeding. The manual contains important information about safely operating the machine. If you do not know this information, you could seriously injure yourself or others. 1. Park the machine on a level, smooth surface with sufficient space to access both sides of the mowing deck. Figure 1 Model 74130 2.
PAGE 3
Installing the Deck Belt Guard Parts needed for this procedure: 2 Bolt (1.25 mm) 2 Washer 2 Locknut (1.25 mm) Procedure Figure 4 Model 74134 1. Loosen, but do not remove, the nut on the outside of each suspension bracket on the rear of the deck (refer to Figure 3 and Figure 4). 1. Knob, existing 3. Bolt 2. Washer 4. Nut 2. Mount the assembled deck belt guard onto the deck as shown in Figure 5, tightening all fasteners securely. Figure 3 Model 74130 1. Nut Figure 5 Model 74130 1. Washer 2.
PAGE 4
1 2 g02461 1 Figure 7 1. bolt heads Figure 6 Model 74134 1. Washer 2. Knob, existing 4. Rear slots 5. Bolt 3. Nut (2) 6. Tab 3. Verify that the guard is clear of all moving parts, wires, hoses, and other components so that it will not interfere with the safe operation of the machine. 5 3. Verify that the guard is clear of all moving parts, wires, hoses, and other components so that it will not interfere with the safe operation of the machine.