Form No. 3329–530 Z287L Z Master with 72 SFS Side Discharge Mower Model No. 74214—Serial No.
Warning Checking the Engine Oil Level . . . . . . . . . . . . . . Checking the Side Discharge Chute . . . . . . . . . . . Checking the Leveling of the Mower Deck . . . . . Checking the Radiator Coolant . . . . . . . . . . . . . . Greasing the Bearings . . . . . . . . . . . . . . . . . . . . . . Checking the Hydraulic Fluid . . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Think Safety First . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Parking Brake . . . . . . . . . . . . . . . . Servicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . Waste Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . Mercury Tilt Switch . . . . . . . . . . . . . . . . . . . . . . . Mercury Tilt Switch Disposal . . . . . . . . . . . . . . . . Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning and Storage . . . . . . . . . . . . . . . . .
• Become familiar with the safe operation of the equipment, operator controls, and safety signs. • Do not change the engine governor setting or overspeed the engine. • All operators and mechanics should be trained. The owner is responsible for training the users. • Stop on level ground, lower implements, disengage drives, engage parking brake, shut off engine before leaving the operator’s position for any reason including emptying the catchers or unclogging the chute.
• Be aware that loss of traction may occur going downhill. Weight transfer to the front wheels may cause drive wheels to slip and cause loss of braking and steering. • Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running. • Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.
Slope Chart 6
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
1-633818 65-2690 43-8480 93-1122 93-7818 66-1340 1. Warning—read the Operator’s Manual for instructions on torquing the blade bolt/nut to 115–149 N⋅m (85–110 ft.-lb.). 67-5360 CAUTION 98-3798 ROTATING BLADES! STOP ENGINE BEFORE REACHING UNDERNEATH.
98-4387 103-1027 1. Warning—wear hearing protection. 98-5954 99-4686 104-2449 103–0262 99-4612 1. Engine stop 2. Engine run 103-0368 3.
104-4163 1. Explosion hazard 2. No fire, open flames, or smoking. 3. Caustic liquid/chemical burn hazard 104-8172 4. Wear eye protection 5. Read the Operator’s Manual. 6. Keep bystanders a safe distance from the battery. 104-8569 104-7759 104-4164 1. Contains lead; do not discard. 2. Recycle 3. Wear eye protection; explosive gases can cause blindness and other injuries 4. No sparks, flame, or smoking 5. Sulfuric acid can cause blindness or severe burns. 6.
103-2433 106-6570 106-6571 12
Gasoline and Oil Warning Recommended Gasoline Gasoline is harmful or fatal if swallowed. Long–term exposure to vapors can cause serious injury and illness. Use UNLEADED Regular Gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. • Avoid prolonged breathing of vapors. • Keep face away from nozzle and gas tank or conditioner opening. • Keep gas away from eyes and skin.
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY. Rear wheels 2 Suspension Seat 1 Nut 4 Control lever—right 1 Control lever—left 1 Bolt, 3/8 x 1 inch 4 Spring washer, 3/8 inch 4 Key 2 Operator’s Manual 1 Engine Operator’s Manual 1 Parts Catalog 1 Registration card 1 USE Installing the wheels to the traction unit.
Installing the Seat 1. Remove seat from crate. 2. Position seat on the studs in the adjustable tracks (Fig. 3). 2 1 3. Install nuts onto studs (Fig 3). 4 5 1 6 3 m–5596 Figure 4 1. Mounting plate 2. Bolt, 3/8 x 1 inch 3. Spring washer, 3/8 inch 4 2 5. If the ends of the levers hit against each other while in the drive position (Fig. 5) (levers rotated in as far as possible), make adjustments by moving the levers outward to the neutral lock position and carefully bend them outward.
Activating the Battery Warning Bulk electrolyte with 1.265 specific gravity must be purchased from a local battery supply outlet. Charging battery produces gasses that can explode and cause serious injury. Danger • Keep cigarettes, sparks and flames away from battery. • Make sure the ignition switch is off. • Ventilate when charging or using battery in an enclosed space. Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns.
Grease the fittings on the three spindle bearings. Grease until it comes out of the lower seals (Fig. 7). 2 1 1 3 M–5036 Figure 7 m–6478 1. Spindles Figure 8 1. Safe Zone—use the Z Master here on slopes less than 15 degrees or flat areas. Checking the Hydraulic Fluid Check the hydraulic fluid level before the engine is first started; refer to Checking the Hydraulic Fluid, page 37. 2. Use walk behind mower and/or hand trimmer near drop–offs and water. 3.
Controls Switching the Fuel Tanks Become familiar with all the controls (Fig. 10) before you start the engine and operate the machine. The unit has two fuel tanks, one located on the left side and on the right side. Each tank connects to the fuel shut off valve in the control panel. From there a common fuel line leads to the engine (Fig. 12). 2 3 11 1 6 8 To use the right side fuel tank, rotate the fuel shut off valve 1/4 turn to the right from the off location.
1 2 1 2 2 1 m–4201 m–2719 Figure 14 Figure 15 1. PTO—On 2. PTO—Off 3 1. Choke—On 2. Choke—Off m–4163 Figure 13 1. Parking brake—ON 2. Parking brake—OFF 3. Brake stop 1 1 2 Starting and Stopping the Engine 3 2 Starting the Engine 1. Sit on the seat and move the motion controls to the neutral locked position. M–4268 m–2720 2. Set the parking brake; refer to Setting the Parking Brake, page 18. Figure 16 1. Throttle—Fast 2. Throttle—Slow 3.
Disengaging the PTO Important Make sure that the fuel shut off valve is closed before transporting or storing the machine, as fuel leakage may occur. Set the parking brake before transporting. Make sure to remove the key as the fuel pump may run and cause the battery to lose charge. 1. To disengage, push the PTO switch to the Off position (Fig. 18). The Safety Interlock System Caution Caution Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended.
4. Sitting on the seat, engage the parking brake, move the PTO to Off, and lock the motion control levers in to neutral. Now start the engine. While the engine is running, center either motion control and move (forward or reverse); the engine should stop. Repeat for the other motion control. 2 3 1 4 5. Sitting on the seat, disengage the parking brake, move the PTO switch to Off, and move the motion control levers to the neutral lock position. Try starting the engine; the engine should not crank.
1. Raise the height-of-cut lever to the transport position (also the 5 inch [127 mm] cutting height position) (Fig. 20). 2. To adjust, remove the hairpin cotter and clevis pin from the height-of-cut bracket (Fig. 20). 3. Select the hole in the height-of-cut bracket corresponding to the height-of-cut desired, and insert the clevis pin (Fig. 20). 1 4 4. Secure the clevis pin with the hairpin cotter (Fig. 20). 3 5. Move the lever to the selected height. 2 5 1 m–4167 Figure 21 1. Gage wheel 2. Stud 3.
1 1 2 m–6124 m–4818 Figure 23 Figure 22 1. Seat suspension knob 1. By-pass valve 2. Seat position adjustment Using a Rollover Protection System (ROPS) Pushing the Machine by Hand Important Always push the machine by hand. Never tow the machine because hydraulic damage may occur. A ROPS is available and its use is recommended for areas where there are slopes, drop–offs or water. Contact an Authorized Service Dealer for information on obtaining ROPS for your machine.
Loading Machines 1 Use extreme caution when loading units on trailers or trucks. One full width ramp that is wide enough to extend beyond the rear tires is recommended instead of individual ramps for each side of the unit (Fig. 24). The lower rear section of the tractor frame extends back between the rear wheels and serves as a stop for tipping backward. Having a full width ramp provides a surface for the frame members to contact if the unit starts to tip backward.
2. Remove the bracket pin (Fig. 25). 1 4 3 2 2 m–5600 5 Figure 26 1 3 1. Z Stand (positioned in slot) m–5599 2. Crack in side walk or turf 3. Latch resting on pivot tab Figure 25 1. Z Stand 2. Latch 3. Bracket 4. Bracket pin 5. Bottom of slot Driving off of the Z Stand 1. Raise the latch to the unlocked position (Fig. 27). 3. Raise the latch. Swing the stand foot out front and slide the stand toward the machine, into the bottom of the slot (Fig. 25 and 26). 2.
Cutting Speed To improve cut quality, use a slower ground speed in certain conditions. 1 Avoid Cutting Too Low If the cutting width of the mower is wider than the mower you previously used, raise the cutting height to ensure that uneven turf is not cut too short. m–5028 Figure 28 1.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position.
Caution If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug. Servicing the Cutting Blades Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades.
3 5 4 MEASURE FROM CUTTING EDGE TO A LEVEL SURFACE 2 1 m–2539 3 Figure 31 4 M–4226 2. Rotate the opposite ends of the blades forward. Figure 32 3. Measure from a level surface to the cutting edge of the blades at the same position as in step 1 above. The difference between the dimensions obtained in steps 1 and 2 must not exceed 1/8 inch (3 mm). If this dimension exceeds 1/8 inch (3 mm), the blade is bent and must be replaced; refer to Removing the Blades and Installing the Blades, page 30. 1.
Installing the Blades Cleaning the Paper Elements 1. Install the blade onto the spindle shaft (Fig. 32). 1. Lightly tap the element on a flat surface to remove dust and dirt (Fig. 36). Important The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. 2. Inspect the element for tears, an oily film, and damage to the rubber seal. Important Never clean the paper element with pressurized air or liquids, such as solvent, gas, or kerosene.
Changing the Oil Viscosity: See the table below. USE THESE SAE VISCOSITY OILS Replace the oil every 100 hours. 1. Start the engine and let it run for five minutes. This warms the oil so that it drains better. 2. Park the machine so that the drain side is slightly lower than the opposite side to ensure that the oil drains completely. Disengage the power take off (PTO), set the parking brake, stop the engine, and remove the key. 3. Place a pan below the oil drain.
4. Apply a thin coat of new oil to the rubber gasket on the replacement filter (Fig. 39). Danger Rotating shaft and fan can cause personal injury. • Do not operate the machine without the covers in place. • Keep fingers, hands and clothing clear of rotating fan and drive shaft. • Shut off the engine and remove the ignition key before performing maintenance. 3 1 2 Caution m–1256 Swallowing engine coolant can cause poisoning. Figure 39 1. Oil filter 2. Gasket • Do not swallow engine coolant.
Cleaning the Cooling System 1. Position the machine on a level surface, stop the engine, and set the parking brake. Clean the cooling system daily before each use. 2. Tilt the seat up and tilt the engine hood forward. 1. Position the machine on a level surface, stop the engine, and set the parking brake. 3. With the engine cool, drain the coolant by loosening the drain cock in the right rear corner (Fig. 41). Important Before starting the engine, clean grass from the pump drive belt compartment.
Servicing the Spark Plug 9. With the radiator cap off, tilt the engine cover down and put the seat down. Start the engine. Run the engine until it is warm. Check the spark plug(s) after every 100 operating hours. Make sure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug(s) and a gapping tool/feeler gauge to check and adjust the air gap. Install a new spark plug(s) if necessary. 10.
3. Check the gap between the center and side electrodes (Fig. 45). Bend the side electrode (Fig. 45) if the gap is not correct. 2 3 1 1 0.030 inch (0.76 mm) 2 M–4384 Figure 46 m–3215 1. Filter 2. Hose clamp Figure 45 1. Center electrode insulator 2. Side electrode 3. Air gap (not to scale) Draining the Fuel Tank Danger Installing the Spark Plug(s) 1. Install the spark plug(s). Make sure that the air gap is set correctly.
3 1 4 m–3717 M–4384 2 Figure 47 1. Fuel shut-off valve 2. Fuel filter 3. Hose clamp 4. Fuel line Figure 48 Servicing the Spark Arrester Inspect the spark arrester every 50 hours for damage, such as holes in the screen, and for buildup on the screen. If it is damaged, replace it with a new spark arrester. If it is dirty, remove it and clean the screen with a wire brush and/or soak it in solvent. Greasing the Front Caster Pivots Lubricate the front caster pivots once a year. 1.
Servicing the Hydraulic System 3. Grease the fittings on the push arms (Fig. 49). Checking the Hydraulic Fluid Check the hydraulic fluid level before engine is first started. Check the hydraulic fluid level after first 8 operating hours. Check the hydraulic fluid level after every 25 operating hours. Fluid Type: Mobil 1 15W-50 synthetic motor oil or equivalent synthetic oil. Important Use the oil specified or equivalent. Other fluids could cause system damage. Hydraulic System Oil Capacity: 67 oz.
Important Do not substitute an automotive oil filter or severe hydraulic system damage may result. 1 2 2. Tilt the seat forward to access the filter. 3. Remove the hydraulic reservoir cap and temporarily cover the opening with a plastic bag and rubber band to prevent all hydro fluid from draining out. 4 3 4. Place a drain pan under the filter, remove the old filter, and wipe the filter adapter gasket surface clean (Fig. 52). m–5615 Figure 51 1. Cap 2. Baffle 3. Cold fluid level—full 4.
Warning 1 3 Hydraulic fluid escaping under pressure can penetrate skin and cause injury. • If hydraulic fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this type of injury. Gangrene may result if this is not done. • Keep body and hands away from pin hole leaks or nozzles that eject high pressure hydraulic fluid. • Use cardboard or paper to find hydraulic leaks.
Setting the Hydraulic Pump Neutral 2 3 Note: Adjust handle neutral first. That has to be correct before the following adjustment can be made. Danger 1 Mechanical or hydraulic jacks may fail to support machine and cause a serious injury. m–6282 Figure 54 1. Neutral locked position 2. Control lever • Use jack stand when supporting machine. • Do not use hydraulic jacks. 3. Neutral potion Warning 6. If adjustment is needed, loosen the nut and jam nut against the yoke (Fig. 55). 7.
2 1 Warning 4 Electrical system will not perform proper safety shut off with jumper wire installed. • Remove jumper wire from wire harness connector and plug connector into seat switch when adjustment is completed. • Never operate this unit with jumper installed and seat switch bypassed. 7. After both pump neutrals are set, shut off the machine. 8. Remove jumper wire from wire harness connector and plug connector into seat switch. 9. Reinstall prop rod and lower the seat into position.
Checking the Wheel Hub Slotted Nut 2 Check after every 500 operating hours. 3 The slotted nut needs to be torqued to 125 ft.-lb. (170 N⋅m). 4 1. Stop the engine, set the parking brake, remove the key, and disconnect the spark plug wire(s) from the spark plug(s). 2. Remove the cotter pin. 1 3. Torque the slotted nut to 125 ft.-lb. (170 N⋅m) (Fig. 59). m–6280 4. Check the distance from the bottom of the slot in the nut to the inside edge of the hole. Two threads or less should be showing (Fig. 59).
Note: When properly adjusted, the front blade tip will be slightly lower than the rear blade tip. See Checking for Bent Blades on page 28 to measure. 5. Place 2 thick blocks (1-1/2 inch [38 mm]) under the rear left and right lower edge of the mower. Place 1 block (2-1/4 inch [57 mm]) under the front center lower edge of the mower. Lower the mower to the 2 inch (51 mm) height-of-cut position (Fig. 60). 10.
Check belts for cracks, frayed edges, burn marks, or any other damage. Replace damaged belts. Replacing the PTO Drive Belt Replacing the Deck Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn drive belt. Replace the PTO drive belt if any of these conditions are evident. Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn deck belt.
4 5 2 m–3748 3 2 1 Figure 63 1. Clutch 2. Clutch retaining strap 3. Clutch terminal 5 Figure 65 4. PTO belt 5. Machine frame 1. Center bolt, spring loaded idler 2. Alignment hole 9. If an adjustment is required, loosen the fixed idler on the right support plate and move it up or down in the adjustment slot (Fig. 66). To relieve the belt tension, lift up on the spring loaded idler. 1 4 m–3744 1 M–4373 2 3 1 2 m–3746 m–4311 Figure 64 1. Clutch pulley 2. PTO drive belt 3.
1 3 3. If an adjustment is necessary, loosen the jam nut below the spring and tighten the nut directly below the yoke (Fig. 69). Turn the nut until the correct measurement is obtained. Tighten the two nuts together and repeat on the opposite side of the unit. 4 4. Turn the nuts clockwise to shorten the spring length and counterclockwise to lengthen the spring. 2 5. Engage the parking brake, lever up. m–6273 6. Measure the distance between the trunnion roller and the collar on the brake rod.
2. To replace a fuse, pull out on the fuse to remove it (Fig. 70). Danger 2 Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns. • Do not drink electrolyte and avoid contact with skin, eyes or clothing. Wear safety glasses to shield your eyes and robber gloves to protect your hands. • Fill the battery where clean water is always available for flushing the skin. • Follow all instructions and comply with all safety messages on the electrolyte container.
9 5 4 11 Warning 2 Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 7 6 7 • Always Disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always Reconnect the positive (red) battery cable before reconnecting the negative (black) cable. 3 8 10 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to off.
Charging the Battery Mercury Tilt Switch The tilt switch on this unit is located under the seat. Tilt the seat up to gain access. Warning The tilt switch on this unit contains mercury, a hazardous material. Mercury that is outside a sealed container vaporizes at room temperature. The vapors are harmful. Mercury can be absorbed through the skin. Do not attempt to open or repair this switch. Charging the battery produces gasses that can explode.
BK PTO CLUTCH DK.GN SHOWN WITH LEVER IN NEUTRAL POSITION LT.GN (NEUTRAL) SW5 LT.BU SHOWN WITH LEVER IN NEUTRAL POSITION LT.BU SW4 (NEUTRAL) SHOWN WITH PARK BRAKE DISENGAGED GND GY SW3 (BRAKE) SHOWN IN OFF POSITION DK.
Cleaning and Storage Important Do not store stabilizer/conditioned gasoline over 90 days. 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to Off. Remove the key. 12. Remove the spark plug(s) and check its condition; refer to Servicing the Spark Plug, page 34. With the spark plug(s) removed from the engine, pour two tablespoons of engine oil into the spark plug hole. Now use the starter to crank the engine and distribute the oil inside the cylinder.
Troubleshooting Problem Starter does not crank. Engine g will not start, starts hard, or f il to fails t keep k running. i Engine g loses power. Engine g overheats. Possible Causes Corrective Action 1. Blade control (PTO) is engaged. 1. Move blade control (PTO) to Disengaged. 2. Parking brake is not on. 2. Set parking brake. 3. Operator is not seated. 3. Sit on the seat. 4. Battery is dead. 4. Charge the battery. 5. Electrical connections are corroded or loose. 5.
Problem Machine does not drive. Abnormal vibration. Uneven cutting g height. g Blades do not rotate. Possible Causes Corrective Action 5. The crankcase oil level is incorrect. 5. Fill or drain to the full mark. 6. The fuel mixture is lean. 6. Contact your Authorized Service Dealer. 7. Excessive loading. 7. Reduce load; use lower ground speed. 1. Traction belt is worn, loose or broken. 1. Contact Authorized Service Dealer. 2. Traction belt is off pulley. 2. Contact Authorized Service Dealer.
The Toro Total Coverage Guarantee LCE A Limited Warranty Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the listed Toro Products if defective in materials or workmanship. The following time periods apply from the date of purchase: You must maintain your Toro Product by following the maintenance procedures described in the operator’s manual.
