Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74253

FormNo.3361-727RevA

Z580ZMaster

Mowers

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Unfoldthecrate.

Nopartsrequired

–

Checkthetirepressure.

Bolt,(3/8x1inch)

Flangenut,(3/8inch)

Curvedwasher

InstalltheRollOverProtectionSystem

(ROPS)

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Chargethebattery.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

Operator’sManual

EngineOwner’sManual

RegistrationCard

Operatortrainingmaterial

Key2

Deliveringthemachinetothecustomer.

UnfoldingtheCrate

NoPartsRequired

Procedure

RefertothePackagingCrateInstructionsincludedwith

themachine.

CheckingtheTirePressure

NoPartsRequired

Procedure

Pressure:13psi(90kPa)

Note:Thefrontcasterwheelsaresemi-pneumatictires

anddonotneedtobechecked.

Checktheairpressureinthedrivetires.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3361-727 Rev A Z580 Z Master® Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 Description Use Qty. No parts required – Unfold the crate. No parts required – Check the tire pressure. Bolt, (3/8 x 1 inch) Flange nut, (3/8 inch) Curved washer 8 8 8 Install the Roll Over Protection System (ROPS) No parts required – Add fuel to the machine. No parts required – Charge the battery.
PAGE 2
Figure 1 Figure 2 2. Remove this hardware and discard it 1. Roll Over Protection System (ROPS) 3 2. Install the ROPS to the frame on both sides with 8 bolts (3/8 x 1 inch), 8 curved washers, and 8 flange nuts (3/8 inch) (Figure 3). Installing the Roll Over Protection System (ROPS) Parts needed for this procedure: 8 Bolt, (3/8 x 1 inch) 8 Flange nut, (3/8 inch) 8 Curved washer Procedure The Roll Over Protection System (ROPS) is not installed in the correct position for shipping purposes. 1.
PAGE 3
5 6 Charging the Battery Checking the Machine for Grease No Parts Required Parts needed for this procedure: Procedure 1 tube Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Procedure Charging the battery produces gasses that can explode and cause serious injury. 1. Remove the belt covers as shown below. • Keep cigarettes, sparks and flames away from the battery. • Make sure the ignition switch is off.
PAGE 4
Figure 6 Figure 8 5. Check the grease for the pump belt idler arm (Figure 7). 7 Checking the Engine Oil Level No Parts Required Procedure Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking Oil Level in Operator’s Manual. Figure 7 6. Check the grease for the PTO drive belt idler arm (Figure 8).
PAGE 5
8 Checking the Side Discharge Chute No Parts Required Procedure If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. Figure 9 1. Grass Deflector An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury or death. Also, contact with the blade could occur. 2. Spring 3.
PAGE 6
9 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check that all mower spindles are greased. Check the engine oil level. Check the hydraulic fluid level.
PAGE 7
10 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Engine Owner’s Manual 1 Registration Card 1 Operator training material 2 Key Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 8
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: Fuel tank caps Oil fill cap/ Oil dipstick Engine oil filter Engine oil drain Fuel filters Air filter Radiator coolant Hydraulic fluid reservoir Hydraulic filter Battery Ignition switch Throttle lever Malfunction indicator light (MIL) and Engine Temperature light Power take off switch (PTO) Motion control levers Parking brake Mower height-of-cut Lift assist lever Z Stand® (Only