Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74311

FormNo.3383-798RevB

ZMaster

8000SeriesRidingMower

with42inor48inDirect-CollectCuttingUnit

ModelNo.74310—SerialNo.314000001andUp

ModelNo.74311—SerialNo.314000001andUp

ModelNo.74312—SerialNo.314000001andUp

SetupInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Theengineexhaustfromthisproduct

containschemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orotherreproductiveharm.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Openthecrate.

Rearcasterwheel1

Bolt(1/2x13inches)

Locknut(1/2inch)

Removethemachinefromthecrate.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Checkthewheellugnuttorque.

Wingnut(1/4inch)

2Installthebattery.

Nopartsrequired

–

Chargethebattery.

Nopartsrequired

–

Checkthehydraulicoil.

Number2general-purposelithium-base

ormolybdenum-basegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3383-798*B

Summary of content (12 pages)

PAGE 1
Form No. 3383-798 Rev B Z Master® 8000 Series Riding Mower with 42in or 48in Direct-Collect Cutting Unit Model No. 74310—Serial No. 314000001 and Up Model No. 74311—Serial No. 314000001 and Up Model No. 74312—Serial No. 314000001 and Up Setup Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Procedure Description Use Qty. 10 No parts required – Check the machine before delivery to the customer (All machines). 11 Operator's Manual Engine Owner's Manual Registration card Operator-training material Key 1 1 1 1 2 Delivering the machine to the customer (All machines). 2. Remove the bolt holding the rear-frame support to the frame (Figure 1).
PAGE 3
provide support for the deck when the unit is driven off of the crate (Figure 4). Figure 2 1. Bolt (1/2 x 13 inches) 3. Locknut (1/2 inch) 2. Rear caster wheel 1 2 3 g026150 Figure 4 7. Carefully remove the jack stands and lower the machine. 1. Drive tire Important: Ensure the mower deck is in the upright position before raising the front of the machine. 8. Raise the front of the machine and support it with jack stands or an equivalent support (Figure 3). 3.
PAGE 4
1 2 3 4 Figure 6 3. Push the deck locking pin in and rotate toward the front to lock 1. Deck lift handle g026151 Figure 8 2. Rotate the deck locking pin toward the rear and pull outward to unlock 1. Front caster 2. Rear deck rollers 15. Push the deck-locking pins inward and rotate them forward to securely lock the deck in the lowered position. 3. Plywood between drive wheels 4.
PAGE 5
2. Remove the bolt holding the rear frame to the crate (Figure 11). 3. Lift the front of the hopper up. Note: Use care when hoisting the machine to prevent damage to the hopper. 4. Using the hoist, lift the machine at the location shown in Figure 9. Figure 10 3. Place jack stands at the arrows 1. Rear caster fork 2. Bolt holding rear frame 6. Remove and discard the rear-frame support and its hardware, located behind the drive tires. 7.
PAGE 6
Figure 13 Figure 12 1. Deck support pin 3. Side-strut hardware 2. Strut between the deck-support pins 1. Lift points on each side of the seat Important: Ensure the mower deck is in the upright position before raising the front of the machine. 21. With the deck locking pins pulled out in the unlock position, carefully lower the deck (Figure 14). 13. Raise up the front of the machine, just enough to remove and discard the deck support from under the rear deck rollers. 14.
PAGE 7
WARNING 6 Operating mower without locking pins securely latched can result in the mower deck folding up unexpectedly. The mower deck folding up unexpectedly can cause serious injury. Installing the Battery Parts needed for this procedure: Always operate mower with locking pins securely latched.
PAGE 8
Note: If time does not permit charging the battery, or if charging equipment is not available, connect the negative battery cable and run the vehicle continuously for 20 to 30 minutes to sufficiently charge the battery. 8 Checking the Hydraulic Oil 7 No Parts Required Charging the Battery Procedure The machine is shipped with hydraulic oil in the reservoir. No Parts Required 1. Check and ensure the reservoir has hydraulic oil. 2. If needed add Toro HYPR-OIL™ 500 hydraulic oil. Procedure 3.
PAGE 9
Checking the Machine for Grease Parts needed for this procedure: 1 tube Number 2 general-purpose lithium-base or molybdenum-base grease. (Purchase separately.) Procedure Before you use the machine, check the machine for grease; refer to Lubrication in the Operator's Manual.
PAGE 10
Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the machine. Check the mower deck gearboxes for oil. Check the engine-oil level. Check the hydraulic-fluid level.
PAGE 11
Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator's Manual 1 Engine Owner's Manual 1 Registration card 1 Operator-training material 2 Key Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No. Serial No.
PAGE 12
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank • Oil fill cap/Oil dipstick • Spark plug(s) • Engine-oil filter • Engine-oil drain • Fuel gauge, valve and hose • Air filter • Hydraulic-fluid reservoir • Hydraulic filter • Battery • Ignition switch • Throttle lever • Choke (if applicable) • Power take off (PTO) • Motion-control levers • Parking brake • Height-of-cut • Adjustable