Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74313

FormNo.3420-439RevA

ZMaster

8000SeriesRidingMower

with42inor48in/122cmCuttingUnit

ModelNo.74310—SerialNo.316000001andUp

ModelNo.74311TE—SerialNo.316000001andUp

ModelNo.74312—SerialNo.316000001andUp

ModelNo.74313—SerialNo.316000001andUp

ModelNo.74315—SerialNo.400000000andUp

SetupInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

TheengineexhaustfromthisproductcontainschemicalsknowntotheStateof

Californiatocausecancer,birthdefects,orotherreproductiveharm.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Openthecrate.

Rearcasterwheel1

Bolt(1/2x13inches)

Locknut(1/2inch)

Removethemachinefromthecrate.

ROPSKit(soldseparately)

InstalltheROPS(International

machinesonly).

Longguard1

Guard

Bolt(1/4x1inch)

Flatwasher(1/4inch)

Retainernut(1/4inch)

InstallthePTO-shaftguards

(Internationalmachinesonly).

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Checkthetorqueofthewheellugnuts.

Wingnut(1/4inch)

2Installthebattery.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3420-439*A

Summary of content (16 pages)

PAGE 1
Form No. 3420-439 Rev A Z Master® 8000 Series Riding Mower with 42in or 48in/122cm Cutting Unit Model No. 74310—Serial No. 316000001 and Up Model No. 74311TE—Serial No. 316000001 and Up Model No. 74312—Serial No. 316000001 and Up Model No. 74313—Serial No. 316000001 and Up Model No. 74315—Serial No.
PAGE 2
Procedure 9 10 11 Description Use Qty. No parts required – Charge the battery. No parts required – Check the hydraulic Fluid. No. 2 lithium grease (Purchase separately.) 1 tube Check the machine for grease. 12 No parts required – Check the machine before delivery to the customer. 13 Operator's Manual Engine owner's manual Registration card Operator training material Key 1 1 1 1 2 Deliver the machine to the customer.
PAGE 3
CAUTION Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not support the machine or may malfunction, allowing the machine to fall and cause injury. Do not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support. 3. g025175 Figure 2 1. Bolt (1/2 x 13 inches) 3. Locknut (1/2 inch) 2. Rear caster wheel Raise the rear of the machine approximately 25.
PAGE 4
that the crate opening under the mower deck is fully covered. 10. 14. Place a plywood sheet (58.4 cm x 81.3 cm or 23 inches x 32 inches), or similar support, over the opening to provide support for the deck when you drive the machine off the crate (Figure 4). With the deck-locking pins pulled out in the unlock position, carefully lower the deck (Figure 6). g026150 g006790 Figure 4 1. Drive tire Figure 6 3. Plywood sheet under the rear deck rollers 3.
PAGE 5
1. Remove the rear caster-wheel assembly from inside the hopper. 2. Remove the bolt holding the rear frame to the crate (Figure 11). 3. Lift the front of the hopper up. Note: Use care when hoisting the machine to prevent damaging the hopper. 4. Using the hoist, lift the machine at the location shown in Figure 9. g026151 Figure 8 1. Front caster 2. Rear-deck rollers 3. Plywood between the drive wheels 4.
PAGE 6
g025317 Figure 10 3. Place jack stands at the arrows 1. Rear caster fork 2. Bolt holding rear frame g026290 6. 7. 8. Figure 12 Remove and discard the rear-frame support and its hardware which is located behind the drive tires. 1. Lift points on each side of the seat Install the rear caster wheel to the rear caster fork with a bolt (1/2 x 13 inches) and locknut (1/2 inch) As shown in Figure 11. Important: Ensure the mower deck is in the upright position before raising the front of the machine.
PAGE 7
3 Installing the ROPS International Machines Only Parts needed for this procedure: 1 Procedure g025171 Figure 13 1. Deck-support pin ROPS Kit (sold separately) Install the ROPS Kit as described in the Installation Instructions for the kit. 3. Side-strut hardware 2. Strut between the deck-support pins 21. 4 With the deck-locking pins pulled out in the unlock position, carefully lower the deck (Figure 14).
PAGE 8
5 Checking the Tire Pressure No Parts Required Procedure Pressure: 103 kPa (15 psi) g036545 Figure 15 1. Bolts Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the correct tire type, correct air pressure needed, and procedure. 2. Rubber guard 4. Fold the guard forward. 5. Install the metal guards with the attached bolts shown in Figure 16.
PAGE 9
terminal first, then the negative (black) cable to the negative battery terminal. Slip the insulator boot over the positive terminal. 8 Note: If time does not permit charging the battery, Installing the Battery or if charging equipment is not available, connect the negative battery cable and run the vehicle continuously for 20 to 30 minutes to sufficiently charge the battery.
PAGE 10
12. 10 Replace the hydraulic reservoir cap and tighten until snug. Do not overtighten. 11 Checking the Hydraulic Fluid Checking the Machine for Grease No Parts Required Procedure Parts needed for this procedure: The machine is shipped with hydraulic fluid in the reservoir. 1 tube No. 2 lithium grease (Purchase separately.) 1. Check and ensure the reservoir has hydraulic fluid. Procedure 2. If needed add Toro HYPR-OIL™ 500 hydraulic fluid.
PAGE 11
12 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the machine. Check the mower-deck gearboxes for fluid. Check the engine-oil level.
PAGE 12
13 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator's Manual 1 Engine owner's manual 1 Registration card 1 Operator training material 2 Key Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No. Serial No.
PAGE 13
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Fuel tank • Oil fill cap/Oil dipstick • Spark plug(s) • Engine-oil filter • Engine-oil drain • Fuel gauge, valve and hose • Air filter • Hydraulic-fluid reservoir • Hydraulic filter • Battery • Ignition switch • Throttle lever • Choke (if applicable) • Power takeoff (PTO) • Motion-control levers • Parking brake • Height-of-cut • Adjustable s
PAGE 14
Notes:
PAGE 15
Notes:
PAGE 16