Form No. 3329–249 Z14–38, Z16–42, or Z17-42 TimeCutter Z with Side Discharge Mower Model No. 74301—Serial No. 230000001 and Up Model No. 74330—Serial No. 230000001 and Up Model No. 74350—Serial No.
Page The Safety Interlock System . . . . . . . . . . . . . . . . 14 Testing the Safety Interlock System . . . . . . . . . . . 14 Driving Forward or Backward . . . . . . . . . . . . . . . 15 Stopping the Machine . . . . . . . . . . . . . . . . . . . . . . 15 Adjusting the Height of Cut . . . . . . . . . . . . . . . . . 16 Adjusting the Mower Wheels (For Models 74330 and 74350 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Positioning the Seat . . . . . . . . . . . . . . . . . . . . . . .
serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product. Safety This machine meets or exceeds the B71.1–1998 specifications of the American National Standards Institute, in effect at the time of production. However, improper use or maintenance by the operator or owner can result in injury.
• Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions. Children • Use extra care when loading or unloading the machine into a trailer or truck. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Always wear safety goggles or safety glasses with side shields when operating mower.
• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Use only genuine Toro replacement parts to ensure that original standards are maintained. Toro Riding Mower Safety The following list contains safety information specific to Toro products or other safety information that you must know that is not included in the ANSI standards. • Engine exhaust contains carbon monoxide, which is an odorless, deadly poison that can kill you.
Slope Chart 7
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Note: If needed, a Decal Kit, 106–8708, and Fench manual are available. Order the Decal Kit from the Toro Parts Department and the French manual from either the Toro Parts Department or online at www.toro.com. 68-3650 68-3660 105-7015 79-3140 106-2223 93-1122 106-2224 1. 2. 3. 4.
6-8716 104-4163 1. Explosion hazard 2. No fire, open flames, or smoking. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 5. Read the Operator’s Manual. 6. Keep bystanders a safe distance from the battery. 106-8742 1. Parking brake 106-7026 106-8743 1. Height of cut 106-7043 1. Do not tow the machine; pull the lever out to ride on the machine or push the lever in to push the machine.
104-5091 1. Contains lead; do not discard. 2. Recycle 3. Wear eye protection; explosive gases can cause blindness and other injuries 4. No sparks, flame, or smoking 5. Sulfuric acid can cause blindness or severe burns. 6. Flush eyes immediately with water and get medical help fast. 7. Maximum fill line 106-2225 11 8. Minimum fill line 9.
Gasoline and Oil Recommended Gasoline Warning Use UNLEADED Regular Gasoline suitable for automotive use (87 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. Gasoline is harmful or fatal if swallowed. Long–term exposure to vapors can cause serious injury and illness. Important Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline.
Controls Operation Become familiar with all of the controls (Fig. 3 and 4) before you start the engine and operate the machine. Note: Determine the left and right sides of the machine from the normal operating position. 3 2 Think Safety First Please carefully read all of the safety instructions and decals in the safety section. Knowing this information could help you, your family, pets or bystanders avoid injury. 1 Danger Mowing on wet grass or steep slopes can cause sliding and loss of control.
Starting and Stopping the Engine 2 1 3 Starting the Engine 4 1. Sit down on the seat and move the motion controls to the brake position. m–4268 Figure 7 2. Move the PTO (power take off) to Off (Fig. 5). 1. Off 2. Run 3. Start 4. Ignition 2 1 Stopping the Engine 1. Move the throttle lever to Fast (Fig. 6). m–4201 2. Move the PTO to Off (Fig. 5). Figure 5 1. PTO—On 3. Turn the ignition key to Off (Fig. 7). 2. PTO—Off 4.
2 3. While sitting on the seat, move the PTO to Off, and lock the motion control levers in neutral. Start the engine. While the engine is running, move the motion control levers to the center, unlocked position, engage the PTO, and rise slightly from the seat; the engine should stop. 1 m–4201 Figure 8 1. PTO—On Driving Forward or Backward 2. PTO—Off The throttle control regulates the engine speed as measured in rpm (revolutions per minute).
Backward 1. Move the levers to the center, unlocked position. 2. To go backward, slowly pull the motion control levers rearward (Fig. 9). To go straight, apply equal pressure to both motion control levers (Fig. 9). To turn, release the pressure on the motion control lever toward the direction you want to turn (Fig. 9). G F To stop, push the motion control levers to neutral.
Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. 1 1. Raise the seat and loosen the adjustment knobs (Fig. 12). 2 3 2. Move the seat to the desired position and tighten the knobs. m–6417 1 Figure 13 1. Control lever 2. Bolt 3. Control arm shaft Pushing the Machine by Hand Important Always push the machine by hand. Never tow the machine because damage may occur. m–6433 Figure 12 1.
1 3 2 2 3 1 m–6423 Figure 15 1. Footrest 2. Rod m–6418 3. Hole positions Figure 14 1. Position for operating the machine 2. Position for pushing the machine Removing and Installing the Engine Hood To Operate the Machine 1. To remove the hood, loosen the knobs and then pull the hood back and up (Fig. 16). Push the two bypass levers towards the inside and then pull them rearward (Fig. 14). Note: The machine will not drive unless the bypass levers are pushed in and then to the outside.
Cutting a Lawn for the First Time Cut grass slightly longer than normal to ensure that the cutting height of the mower does not scalp any uneven ground. However, the cutting height used in the past is generally the best one to use. When cutting grass longer than six inches tall, you may want to cut the lawn twice to ensure an acceptable quality of cut. 1 2 Cut 1/3 of the Grass Blade It is best to cut only about 1/3 of the grass blade.
Keep the Underside of the Mower Clean Clean clippings and dirt from the underside of the mower after each use. If grass and dirt build up inside the mower, cutting quality will eventually become unsatisfactory. Blade Maintenance Maintain a sharp blade throughout the cutting season because a sharp blade cuts cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval Each use After first 5 hours Maintenance Procedure • Check the engine oil level. • Check the safety system. • Clean the mower housing. • Change the engine oil. Every 5 hours • Check the cutting blades. Every 25 hours • • • • • • Every 50 hours • Change the engine oil.2 Every 100 hours • • • • • Clean the cooling system.
Servicing the Engine Oil 1 2 Check the oil level daily or after every 8 hours. Change the oil after the first 5 operating hours and every 50 operating hours thereafter. Oil Type: Detergent oil (API service SF, SG, SH, SJ, or higher) Crankcase Capacity: 3 • 48 oz./1-1/2 qt. (1400 cc/1.4 l) when the filter is not changed; • 56 oz./1-3/4 qt. (1700 cc/1.7 l) when the filter is changed (Models 74330 and 74350 only) m–6439 Figure 18 1. Oil dipstick 2. Filler tube Viscosity: See the table below. 3.
3. Disengage the PTO and set the parking brake. 2. Remove the old filter and wipe the filter adapter gasket surface (Fig. 21). 4. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Apply a thin coat of clean oil to the rubber gasket on the replacement filter (Fig. 21). 5. Slide the drain hose over the drain valve. 3 6. Place a pan below the drain hose. Rotate oil drain valve to allow oil to drain (Fig. 20). 2 7.
Important worn. 2 1 Replace the foam element if it is torn or Cleaning the Paper Element: 1. Lightly tap the element on a flat surface to remove dust and dirt. 2. Carefully clean the rubber seal on the paper element to prevent debris from entering the engine. 3. Inspect the element for tears, an oily film, and damage to the rubber seal. Important Never clean the paper element with pressurized air or liquids, such as solvent, gas, or kerosene.
1 Servicing the Cutting Blades Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. 2 Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade.
Warning 2 A blade that is bent or damaged could break apart and could seriously injure or kill you or bystanders. 1 3 • Always replace bent or damaged blade with a new blade. • Never file or create sharp notches in the edges or surfaces of blade. m–151 Figure 26 1. Cutting edge 2. Curved area 3. Wear/slot forming Removing the Blades Checking for Bent Blades The blades must be replaced if a solid object is hit, if the blade is out of balance, or the blade is bent.
3. Clean the grease fittings with a rag. Make sure to scrape any paint off of the front of the fitting(s). 1 4. Connect a grease gun to the fitting. Pump grease into the fittings until grease begins to ooze out of the bearings. m–1854 Figure 29 5. Wipe up any excess grease. 1. Sharpen at original angle Where to Add Grease 2. Check the balance of the blade by putting it on a blade balancer (Fig. 30). If the blade stays in a horizontal position, the blade is balanced and can be used.
Servicing the Battery Warning Warning Incorrect battery cable routing could damage the tractor and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. CALIFORNIA Proposition 65 Warning • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always connect the positive (red) battery cable before connecting the negative (black) cable.
3. Remove the vent caps from the battery (Fig. 34). 5. Slide the red terminal boot onto the positive (red) battery post. 4. Slowly pour distilled water into each battery cell until the electrolyte level is up to the Upper line (Fig. 34) on the battery case. 6. Secure the battery with the hold-down (Fig. 33). Checking the Electrolyte Level Important Do not overfill the battery because electrolyte (sulfuric acid) can cause severe corrosion and damage to the chassis. Danger 5.
Draining the Fuel Tank Replacing the Fuel Filter Replace the fuel filter after every 100 operating hours or yearly, whichever occurs first. Danger Never install a dirty filter if it is removed from the fuel line. In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. 1. Park the machine on a level surface and disengage the blade control (PTO). 2.
2. Move the motion control levers to the brake position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 1 3. Check the air pressure of all four tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure, page 30. 4 4. Set the height-of-cut lever to position D [3 inch (76 mm)]. 2 5. Carefully rotate the blade(s) side to side (Fig. 38). Measure between the outside cutting edges and the flat surface (Fig. 38).
4. Check and adjust the side-to-side blade level if you have not checked the setting; refer to Leveling the Mower from Side-to-Side, page 30. m–6427 3 2 1 5. Measure the length of the rod extending out of the adjusting block on the sides of the chassis (Fig. 41). 1 6. If the rod length is not a 3/4 inch (19 mm), remove the hairpin cotter and washer from the end of the adjusting rod (Fig. 41) and turn the rod until the 3/4 inch (19 mm) dimension is obtained. 2 3 7.
Inspecting the Belts 5 Inspect all belts every 100 hours. 6 Check the belts for cracks, frayed edges, burn marks, or any other damage. Replace damaged belts. 1 1 3 6 Replacing the Mower Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. 3 2 1. Park the machine on a level surface and disengage the blade control (PTO). 8 2.
2. Move the motion control levers to the brake position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Slide the mower under the tractor. 4. Lower the height-of-cut lever to the lowest position. 5. Attach the adjusting rod to the tractor with the washer and hairpin cotter (Fig. 46) on each side of the mower. 2 6. Slide the leveling brackets onto the mounting pins and secure them with the washers and hairpin cotters (Fig. 46). 1 m–6431 7.
Washing the Underside of the Mower Warning A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with blade or thrown debris can cause injury or death. After each use, wash the underside of the mower to prevent grass buildup for improved mulch action and clipping dispersal. 1. Park the machine on a level surface and disengage the blade control (PTO). • Replace broken or missing washout fitting immediately, before using mower again.
Important The grass deflector must be spring loaded in the down position. Lift the deflector up to test that it snaps to the full down position. 5 3 4 2 1 6 7 m–6461 Figure 49 1. 2. 3. 4. Grass deflector Grass deflector bracket Spring Rod 5. Nut, 3/8 inch 6. Internal lock washer 7.
BK BN BLUE GREEN GREY ORANGE BU GN GY OR PTO CLUTCH BROWN BN BK Y W GY BN BLACK Y W VIO T R PK SW2 (PTO) 4 Y GN W SHOWN WITH PARK BRAKE DISENGAGED SW5 (BRAKE) SHOWN WITH PARK BRAKE DISENGAGED SW3 (BRAKE) PK YELLOW WHITE VIOLET TAN RED PINK SHOWN IN OFF POSITION 7 GND 1 WIRE COLOR CODES 5 2 4 3 37 1 I OR OR X K1 (KILL RELAY) W Y SW4 (SEAT) SHOWN WITH OPERATOR IN SEAT PK Y BU BU S SW1 (IGNITION) VIO R SOLENOID A F1 B BK Y F2 GND 10A F3 25A X I
Cleaning and Storage crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s). 1. Disengage the PTO, set the parking brake, stop the engine, and remove the key. 12. Clean any dirt and chaff from the top of the mower. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine cylinder head fins and blower housing. 13.
Troubleshooting Problem The engine g overheats. The starter does not crank. The engine g will not start, starts h d or ffails hard, il tto kkeep running. i Possible Causes Corrective Action 1. The engine load is excessive. 1. Reduce ground speed. 2. The oil level in the crankcase is low. 2. Add oil to the crankcase. 3. The cooling fins and air passages under the engine blower housing are plugged. 3. Remove the obstruction from the cooling fins and air passages. 4. The air cleaner is dirty. 4.
Problem The engine g loses power. The machine does not drive. There is abnormal vibration. Uneven cutting g height. g Possible Causes Corrective Action 1. The engine load is excessive. 1. Reduce ground speed. 2. The air cleaner is dirty. 2. Clean the air cleaner element. 3. The oil level in the crankcase is low. 3. Add oil to the crankcase. 4. The cooling fins and air passages under the engine blower housing are plugged. 4. Remove the obstruction from the cooling fins and air passages. 5.
Problem The blades do not rotate. Possible Causes Corrective Action 1. The drive belt is worn, loose or broken. 1. Install a new drive belt. 2. The drive belt is off of the pulley. 2. Install the drive belt and check the adjusting shafts and belt guides for the correct position. 3. The mower belt is worn, loose, or broken. 3. Install a new mower belt.
Consumer TimeCutter The Toro Total Coverage Guarantee A Two-Year Full Warranty (Limited Warranty for Commercial Use) Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship.
