Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74409

FormNo.3356-151RevD

Z334orZ340ZMaster

Mowers

ForallZ334orZ340ZMasterMowers

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removethemachinefromthecrate.

Bolt(3/8x1inch)

Nut(3/8inch)

Installtheseatlanyard.

Rightcontrollever1

Leftcontrollever

Bolt(3/8x1inch)(2areassembled)

Curvedwasher(3/8inch)(2are

assembled)

Installthemotioncontrollevers.

Nopartsrequired

–

Addingfueltothemachine.

Nopartsrequired

–

Chargethebattery.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Checkthehydraulicoil.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

Operator’sManual

PartsCatalog

EngineOwner’sManual

RegistrationCard

SafetyVideo

Key2

Deliveringthemachinetothecustomer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3356-151 Rev D Z334 or Z340 Z Master® Mowers For all Z334 or Z340 Z Master Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 © 2008—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
1 Removing the Machine from the Crate No Parts Required Procedure 1. Remove the straps holding the machine to the crate. 2. Check the air pressure in the rear tires. Pressure: 13 psi (90 kPa) Note: There is no valve stem located in the front tires, it is a semi-pneumatic tire and does not need to be checked. Figure 2 1. Seat base 2. Bolt (3/8 x 1 inch) 3. Lanyard 4.
PAGE 3
. Raise the levers to the neutral position and align them by sliding them forward or backward and tighten the bolts. 4 4. If the ends of the levers hit against each when rotated into the drive position, move them to the neutral position and carefully bend them outward. Adding Fuel to the Machine 5. Move them back to the drive position and check for clearance. No Parts Required 6. Repeat if necessary. Procedure Note: Make sure both fuel tanks are half full when first starting the machine.
PAGE 4
5 6 Charging the Battery Checking the Machine for Grease No Parts Required Parts needed for this procedure: Procedure 1 tube Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Charging the battery produces gasses that can explode and cause serious injury. Procedure • Keep cigarettes, sparks and flames away from the battery. 2. Check the idler arm for grease. 1. Remove the belt covers. 3. Check the grease for the spindle bearings.
PAGE 5
7 Checking the Engine Oil Level No Parts Required Procedure Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking Oil Level in Operator’s Manual. 8 Figure 7 1. Cap 2. Baffle Preparing the Side Discharge Chute No Parts Required Procedure Remove the plastic tie holding the side discharge chute up and lower the chute into place. 9 Checking the Hydraulic Oil No Parts Required Procedure 1.
PAGE 6
10 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check the engine oil level. Check the hydraulic fluid level. Check the operation of the parking brake.
PAGE 7
11 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Parts Catalog 1 Engine Owner’s Manual 1 Registration Card 1 Safety Video 2 Key Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 8
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: Fuel tank caps Oil fill cap/ Oil dipstick Engine oil filter Engine oil drain Fuel filters Air filter Hydraulic fluid reservoir Hydraulic filters Battery Ignition switch Throttle lever Power take off switch (PTO) Motion control levers Parking brake Mower height-of-cut Adjustable seat Hydraulic bypass valves Refer to theOperator’s Manual to point out safety procedures, operation,