Form No. 3351-689 Z149 Z Master With 44in SFS Side Discharge Mower Model No. 74411—Serial No. 250000001 and Up Operator’s Manual Register your product at www.Toro.
Warning Stopping the Machine . . . . . . . . . . . . . . . . . . . . . . Adjusting the Height-of-Cut . . . . . . . . . . . . . . . . . Adjusting the Anti-scalp Rollers . . . . . . . . . . . . . . Positioning the Seat . . . . . . . . . . . . . . . . . . . . . . . . Pushing the Machine by Hand . . . . . . . . . . . . . . . . Operating with the Side Discharge . . . . . . . . . . . . Transporting the Machine . . . . . . . . . . . . . . . . . . . Loading the Machines . . . . . . . . . . . . . . . . . . . . . .
This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note: emphasizes general information worthy of special attention. Introduction Read this manual carefully to learn how to operate and maintain your product properly. The information in this manual can help you and others avoid injury and product damage. Although Toro designs and produces safe products, you are responsible for operating the product properly and safely.
• Be aware of the mower discharge direction and do not point it at anyone. • Wear appropriate clothing including hard hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry may get tangled in moving parts. • Do not operate the mower under the influence of alcohol or drugs. • Inspect the area where the equipment is to be used and remove all objects such as rocks, toys and wire which can be thrown by the machine.
• Keep all parts in good working condition and all hardware tightened. Replace all worn or damaged decals. Using the Rollover Protection System (ROPS) • Keep the roll bar in the raised and locked position and use the seat belt when operating the machine. • Use only Toro-approved attachments. Warranty may be voided if used with unapproved attachments. • Be certain that the seat belt can be released quickly in the event of an emergency. • Be aware there is no rollover protection when the roll bar is down.
Slope Chart Fold along appropriate line Example: Compare slope with folded edge. Align this edge with a vertical surface (Tree, Building, Fence post, pole, etc.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 65–2690 1-403005 67-5360 1-523552 68-8340 1-633818 98-3798 98-4387 54-9220 1. Warning—wear hearing protection.
98-5954 103-1997 107-2100 103–2644 104-8569 10
107-2112 107-2102 107-2148 11
107-8445 107-9309 1. Warning—read the Operator’s Manual for information on charging the battery; contains lead; do not discard. 2. Read the Operator’s Manual.
108-4050 Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 2. No fire, open flames, or smoking. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 5. Read the Operator’s Manual. 6. Keep bystanders a safe distance from the battery. 7. Wear eye protection; explosive gases can cause blindness and other injuries 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 10. Contains lead; do not discard.
Gasoline and Oil Warning Recommended Gasoline Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. Use unleaded regular gasoline suitable for automotive use (85 pump octane minimum). You may use leaded regular gasoline if unleaded regular is not available. • Avoid prolonged breathing of vapors. • Keep your face away from the nozzle and fuel tank or conditioner opening. • Keep gasoline away from eyes and skin.
1. To lower the roll bar, loosen the front handles (Fig. 2). Operation Note: Determine the left and right sides of the machine from the normal operating position. Using the Rollover Protection System (ROPS) 1 m-7406 Figure 2 Warning 1. Front handle To avoid injury or death from a rollover, keep the roll bar in the raised locked position and use the seat belt. 2. Remove the hairpin cotter pins and remove the 2 pins (Fig. 3). Ensure that the rear part of the seat is secured with the seat latch.
3. Lower the the roll bar to the down position. Danger Note: There are 2 down positions. See Figure 4 for the positions. Operating the machine on wet grass or steep slopes can cause sliding and loss of control. 2 Wheels dropping over the edges can cause rollovers, which may result in serious injury, death, or drowning. 1 There is no rollover protection when the roll bar is down. Always keep the roll bar in the raised and locked position, and use the seat belt. m-7432a Figure 4 1.
Using the Hour Meter Caution The hour meter (Fig. 8) records the number of hours the engine has operated. It operates when the engine is running. Use these times for scheduling regular maintenance. This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. 1 Wear hearing protection when operating this machine. m–4202 Figure 8 1. Hour meter Figure 6 Using the Fuel Shutoff Valve 1. Warning—wear hearing protection.
Operating the Parking Brake 3. Move the PTO (power takeoff) to Off (Fig. 11). 2 Always set the parking brake when you stop the machine or leave it unattended. 1 Important Do not park the machine on slopes unless the wheels are chocked or blocked. 2 Setting the Parking Brake 1 1. Move the motion control levers (Fig. 10) to the neutral lock position. m–4201 1 m–2719 Figure 11 Figure 12 1. PTO—On 2. PTO—Off 1. Choke—On 2. Choke—Off 4.
Stopping the Engine 3. Pull out the power takeoff (PTO) switch to engage the PTO (Fig. 15). 1. Push the PTO to Off (Fig. 13). 2. Move the throttle lever midway between Slow and Fast (Fig. 13). 2 1 3. Let the engine idle for 60 seconds (Fig. 14). 4. Turn the ignition key to Off (Fig. 14). 5. Disconnect the wire from the spark plug(s) to prevent the possibility of someone accidentally starting the machine before it is transported or stored. m–4201 6.
Testing the Safety Interlock System 3. To go forward, slowly push the motion control levers forward (Fig. 16). Test the safety interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair it immediately. 2 3 1. While sitting on the seat, engage the parking brake, engage the PTO, and try to start the engine; the engine should not crank. 1 4 2.
Adjusting the Anti-scalp Rollers Caution Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Whenever you change the height-of-cut, adjust the height of the anti-scalp rollers. Always remove the ignition key and set the parking brake when leaving the machine unattended, even for a few minutes. Adjusting the Outer Roller 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake.
Adjusting the Center Rollers Pushing the Machine by Hand 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. Important Always push the machine by hand. Never tow the machine, because hydraulic damage may occur. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. To Push the Machine 3. After adjusting the height-of-cut, remove the bolt and nut (Fig. 19). 1.
Operating with the Side Discharge Warning Driving on a street or roadway without turn signals, lights, reflective markings, or a slow moving vehicle emblem is dangerous and can lead to accidents that cause personal injury. The mower has a hinged grass deflector that disperses the clippings to the side and down toward the turf. Danger Do not drive the machine on a public street or roadway.
Mowing Direction the downside of the slope and the ramp extends up the slope. This will minimize the ramp angle. The trailer or truck should be as level as possible. Alternate the mowing direction to keep the grass standing straight. This also helps disperse clippings, which enhances decomposition and fertilization. Important Do not attempt to turn the machine while on the ramp; you may lose control and drive off the side.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval After First 8 Hours Each Use Maintenance Procedure • Check the hydraulic fluid level. • Change the engine oil. • Change the hydraulic filter. • • • • Check the engine oil level. Check the safety system. Clean the engine air intake1. Clean the mower housing. Every 25 Hours • Service the foam air cleaner1. • Check the battery electrolyte.
Important Refer to your engine operator’s manual for additional maintenance procedures. Caution If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition and disconnect the wire from the spark plug(s) before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug.
Checking for Bent Blades Removing the Blades 1. Rotate the blades until the ends face forward and backward (Fig. 24). Measure from a level surface to the cutting edge of the blades (Fig. 25). Note this dimension. Replace any blade if it hits a solid object, is out of balance, or is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades.
Sharpening the Blades Cleaning the Cooling System Clean the air intake screen from grass and debris before each use. Warning Check and clean the cooling fins and the engine shrouds every 100 hours or yearly, which ever comes first. When you sharpen the blade, pieces of the blade could be thrown and cause serious injury. 1. Disengage the PTO and set the parking brake. Wear proper eye protection when you sharpen the blade. 2.
Servicing the Air Cleaner Servicing the Primary Filter Primary Filter: Check and/or replace it after every 200 operating hours or more often in dusty conditions. • Check and/or replace the primary filter after 200 operating hours. Safety Filter: Replace it after every 600 operating hours. • If the primary filter is dirty, bent, or damaged, replace it. Note: Check the filters more frequently if the operating conditions are extremely dusty or sandy. • Do not clean the primary filter.
Servicing the Engine Oil 5. Unscrew the oil dipstick and wipe the end clean (Fig. 31). Service Interval/Specification 6. Slide the oil dipstick fully into the filler tube, but do not thread it onto the tube (Fig. 31). Change the engine oil: • After every 100 operating hours 7. Pull the dipstick out and look at the end. If the oil level is low, slowly pour only enough oil into the filler tube to raise the level to the Full mark.
Changing the Oil Filter 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Replace the oil filter every 200 operating hours or every other oil change. 3. Disconnect the wire(s) from the spark plug(s) (Fig. 34). Note: Change the oil filter more frequently when the operating conditions are extremely dusty or sandy. 4. Clean around the spark plug(s) to prevent dirt from falling into the engine and potentially causing damage. 1.
3. Check the gap between the center and side electrodes and bend the side electrode if the gap is not correct (Fig. 35). 7. Remove the filter from the fuel lines. Installing the Spark Plug(s) 9. Open the fuel shutoff valve. 8. Install a new filter and move the hose clamps close to the filter (Fig. 36). 1. Install the spark plug(s). Draining the Fuel Tank Note: Ensure that the air gap is set correctly. 2. Tighten the spark plug(s) to 16 ft-lb (22 N⋅m). Danger 3.
Greasing and Lubrication Greasing the Front Caster Pivots Lubricate the machine at the intervals shown on the Check Service Reference Aid decal (Fig. 37). Lubricate more frequently when operating conditions are extremely dusty or sandy. Lubricate the front caster pivots once a year. 1. Remove the dust cap and adjust the caster pivots. Note: Keep dust cap off until greasing is done. Refer to Adjusting the Caster Pivot Bearing on page 39. 2. Remove the hex plug and thread a grease zerk into the hole. 3.
Where to Add Light Oil or Spray Lubrication 2. Clean area around filler neck of hydraulic tank (Fig. 40). Lubricate the machine in the following areas with spray type lubricant or light oil. Lubricate every 160 hours. 1 2 • Seat switch actuator • Brake handle pivot • Brake rod bushings 4 3 • Motion control bronze bushings Checking the Tire Pressure m–5615 Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause an uneven cut.
Replacing the Hydraulic Filter 5. Install the replacement hydraulic filter onto the filter adapter, but do not tighten. Change the hydraulic filter: 6. Fill the hydraulic tank with hydraulic fluid until the fluid overflows the filter • After the first 8 operating hours • After every 200 operating hours 7. Turn the oil filter clockwise until the rubber gasket contacts the filter adapter, then tighten the filter an additional 1/2 turn (Fig. 42).
5. Move lever to the neutral position but not locked (Fig. 43). Warning Hydraulic fluid escaping under pressure can penetrate skin and cause injury. 2 3 • If hydraulic fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this type of injury; otherwise, gangrene may result. • Keep your body and hands away from pin hole leaks or nozzles that eject high pressure hydraulic fluid. • Use cardboard or paper to find hydraulic leaks.
8. If adjustment is needed, loosen the nut and jam nut against the yoke (Fig. 44). Setting the Left-hand Hydraulic Pump Neutral Position 9. Apply slight rearward pressure on the motion control lever, and turn the head of the adjustment bolt in the appropriate direction until the control lever is centered in the neutral lock position (Fig. 43). 1. Start the engine, open the throttle halfway and release the parking brake. Refer to Starting and Stopping the Engine on page 18.
3. Adjust the pump rod length by rotating the double nuts on the rod in the appropriate direction until the wheel is still or slightly creeps in reverse (Fig. 44). Adjusting the Tracking 4. Move the motion control lever forward and reverse, then back to neutral. The wheel must stop turning or slightly creep in reverse. Important Adjust the handle neutral and the hydraulic pump neutral before adjusting the tracking.
Adjusting the Caster Pivot Bearing Checking the Wheel Hub Slotted Nut Check after every 500 operating hours or at storage, whichever occurs first. Check after every 500 operating hours. The slotted nut needs to be torqued to 125 ft-lb (170 N⋅m). 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. 2.
Leveling the Mower at Three Positions 2. Measure the right blade at the B location (Fig. 49), from a level surface to the cutting edge of the blade tip (Fig. 50). Important There are only 3 measuring positions needed to level the mower. Setting Up the Machine MEASURE FROM CUTTING EDGE TO A LEVEL SURFACE 1. Position mower on a flat surface. 2. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. m–2539 Figure 50 3.
9. Tighten the jam nut under the rear support arm and tighten the bolt that secures the chain to the rear support arm. 7. Loosen the front swivel jam nuts, at the front of the right and left swivels, approximately 1/2 inch (13 mm) (Fig. 54). 10. Adjust the opposite side if needed. 8 1 Adjusting the Front-to-Rear Mower Pitch 8 4 1. Position the right blade front to rear (Fig. 52). Front A 6 7 5 2 B 3 m–7704 m–1078 Front Figure 54 Figure 52 1. 10-1/4 inch (260 mm) between the large washers 2.
Adjusting the Push Arms Inspecting the Belts If needed, adjust the push arms to increase or decrease the mower belt tension. Inspect all belts every 250 hours. Check belts for cracks, frayed edges, burn marks, or any other damage. Replace damaged belts. 1. To adjust the push arms, loosen the jam nut and rotate the ball joint counterclockwise, one turn at a time.(Fig. 55). Replacing the Mower Belt 2. Adjust each side the same amount.
Replacing the Pump Drive Belt 6. Remove the spring loaded idler pulley (Fig. 56). 7. Route the new belt through the idler arm (Fig. 56). Check the pump drive belt for wear after every 50 operating hours. 8. Install the idler pulley and route the belt onto the other pulleys (Fig. 57). 1. Remove the mower belt first; refer to Replacing the Mower Belt on page 42. 1 2. Remove the bolt from the clutch stop and unplug the clutch electrical wire (Fig. 58).
Adjusting the Parking Brake Servicing the Fuses Check the parking brake for proper adjustment. 1. Disengage the brake lever (lever down). The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. 2. Measure the length of the spring; the measurement should be 2-3/4 inch (74 mm) between the washers (Fig. 59).
Installing the Battery Servicing the Battery 1. Position the battery in the tray with the terminal posts toward the engine (Fig. 62). Warning 9 5 4 11 CALIFORNIA 2 Proposition 65 Warning 7 Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. 6 7 3 Checking the Electrolyte Level 1. Shut off the engine and wait for all moving parts to stop. 8 10 1 2.
Removing the Battery Adding Water to the Battery The best time to add distilled water to the battery is just before you operate the machine. This lets the water mix thoroughly with the electrolyte solution. Warning The battery terminals or metal tools could short against metal machine components, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Note: Never fill the battery with distilled water while the battery installed in the machine.
4. When the battery is fully charged, unplug the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Fig. 63). 1. Remove the locknut, bolt, spring, and spacer that hold the deflector to the pivot brackets (Fig. 64). 8 4 2 6 2 4 3 3 1 5 1 m–7710 7 m–4970 Figure 63 1. Positive Battery Post 2. Negative Battery Post m–5037 3. Red (+) Charger Lead 4. Black (–) Charger Lead Figure 64 1. 2. 3. 4. 5. 5.
PTO CLUTCH GND BK BK BN VIO (NEUTRAL) SW5 W SW4 (NEUTRAL) SHOWN WITH PARK BRAKE DISENGAGED SW3 (BRAKE) VIO Y SHOWN WITH LEVER IN NEUTRAL POSITION SHOWN WITH LEVER IN NEUTRAL POSITION Y SHOWN IN OFF POSITION GY BN SW2 (PTO) I S OR BK P1–B T Y K2 (START RELAY) P2–C SW6 (SEAT SW) SHOWN WITH OPERATOR IN SEAT TERMINAL VIEW FROM BACK OF SWITCH B A KEY SW Y X NO CONNECTION BIA AND X Y BIS P1–A DELAY MODULE 100–6186 P1–C PK OFF ON START OR GY BN GN F1 30A Y R R B BK K1
Cleaning and Storage A. Add a petroleum based stabilizer/conditioner to fuel in the tank. Follow mixing instructions from stabilizer manufacture. Do not use an alcohol based stabilizer (ethanol or methanol). 1. Disengage the power takeoff (PTO), set the parking brake and turn the ignition key to off. Remove spark plug wire. Remove the key. Note: A fuel stabilizer/conditioner is most effective when mixed with fresh gasoline and used at all times. 2.
Troubleshooting Problem Starter does not crank. Engine g will not start, starts hard, or f il to fails t keep k running. i Engine g loses power. Engine g overheats. Possible Causes Corrective Action 1. Blade control (PTO) is engaged. 1. Move blade control (PTO) to Disengaged. 2. Parking brake is not on. 2. Set parking brake. 3. Operator is not seated. 3. Sit on the seat. 4. Battery is dead. 4. Charge the battery. 5. Electrical connections are corroded or loose. 5.
Problem Machine does not drive. Abnormal vibration. Uneven cutting g height. g Blades do not rotate. Possible Causes Corrective Action 1. Traction belt is worn, loose or broken. 1. Contact Authorized Service Dealer. 2. Traction belt is off pulley. 2. Contact Authorized Service Dealer. 3. Hydro fluid level low. 3. Add hydro fluid to reservoir. 1. Engine mounting bolts are loose. 1. Tighten engine mounting bolts. 2. Loose engine pulley, idler pulley, or blade pulley. 2.
The Toro Total Coverage Guarantee LCE A Limited Warranty Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the listed Toro Products if defective in materials or workmanship. The following time periods apply from the date of purchase: You must maintain your Toro Product by following the maintenance procedures described in the operator’s manual.