Form No. 3356-852 Rev C TimeCutter® Z380 and Z420 Riding Mowers Model No. 74419—Serial No. 270000001 and Up Model No. 74420—Serial No. 270000001 and Up Register your product at www.Toro.
This spark ignition system complies with Canadian ICES-002 Figure 2 Introduction 1. Safety alert symbol. Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
Removing and Installing the Engine Hood..................... 22 Lubrication................................................ 23 Greasing the Bearings ........................ 23 Engine Maintenance.................................. 23 Servicing the Air Cleaner ................... 23 Servicing the Engine Oil .................... 24 Servicing the Spark Plug .................... 26 Fuel System Maintenance .......................... 27 Draining the Fuel Tank ...................... 27 Replacing the Fuel Filter ...
Safety ◊ being driven too fast; Safe Operation Practices for Ride-on (riding) Rotary Lawnmower Machines ◊ the type of machine is unsuitable for its task; ◊ inadequate braking; ◊ lack of awareness of the effect of ground conditions, especially slopes; This machine meets or exceeds European Standards in effect at the time of production. However, improper use or maintenance by the operator or owner can result in injury.
• Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect. • Mow only in daylight or in good artificial light. • Before attempting to start the engine, disengage all blade attachment clutches and shift into neutral. • Do not use on slopes of more than 15 degrees. • Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care.
information that you must know that is not included in the CEN standard. • Engine exhaust contains carbon monoxide, which is an odorless, deadly poison that can kill you. Do not run engine indoors or in an enclosed area. • Keep hands, feet, hair and loose clothing away from attachment discharge area, underside of mower and any moving parts while engine is running. • Do not touch equipment or attachment parts which may be hot from operation. Allow to cool before attempting to maintain, adjust, or service.
This unit has an equivalent continuous A-weighted whole body vibration level of .195 m/s2, based on measurements of identical machines per EN 1032. Model 74420 This unit has an equivalent continuous A-weighted hand/arm vibration level of 4.66 m/s2, based on measurements of identical machines per EN 1033. This unit has an equivalent continuous A-weighted whole body vibration level of .14 m/s2, based on measurements of identical machines per EN 1032.
Slope Chart 8
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-6677 1. Warning—don’t operate the mower with the deector up or removed; keep the deector in place. 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. 93-7009 1. Warning—don’t operate the mower with the deector up or removed; keep the deector in place. 2.
6-2223 106-8742 1. Parking brake 106-2224 1. 2. 3. 4. 5. 6. Throttle 7. 8. Choke Fast 9. Continuous variable setting10. 11. Slow Power take-off (PTO), Blade control switch on some models 106-8743 Headlights Engine—stop Engine—run Engine—start Ignition 1. Height of cut Battery Symbols Some or all of these symbols are on your battery 108-6109 1. To push the machine, move tow levers forward and then out to lock them into position. 1. Explosion hazard 6. 2. No re, open ame, or smoking. 7. 3.
0-6567 1. Warning—read the Operator’s Manual. 2. Warning—read the instructions before servicing or performing maintenance; move the motion control levers to the brake position, remove the ignition key and disconnect the spark plug wire. 3. Cutting/dismemberment hazard, mower blade; entanglement hazard, belt—do not open or remove safety shields while engine is running. 4.
Product Overview Figure 3 1. Seat 2. Control levers 3. Control panel 4. 5. 6. Height of cut lever Mower deck Footrest 7. Front caster wheel 8. Rear drive wheel 9. Cup holder 12 10.
Controls operator to exit the machine (Figure 4). Always position the motion control levers into the park position when you stop the machine or leave it unattended. Become familiar with all of the controls Figure 5 and Figure 4 before you start the engine and operate the machine. Height-of-Cut Lever The height of cut lever allows the operator to lower and raise the deck from the seated position.
Operation Recommended Gasoline Note: Determine the left and right sides of the machine from the normal operating position. Use UNLEADED Regular Gasoline suitable for automotive use (87 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. Think Safety First Important: Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline.
• Cleans the engine while it runs • Eliminates gum-like varnish buildup in the fuel system, which causes hard starting In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. Important: Do not use fuel additives containing methanol or ethanol. Add the correct amount of gas stabilizer/conditioner to the gas.
Figure 9 1. Off 2. Run 3. 4. Start Ignition Figure 7 1. Blade control switch—On 2. Stopping the Engine Blade control switch—Off 1. Move the throttle lever to Fast (Figure 8). 3. Move the throttle lever to Choke before starting a cold engine (Figure 8). 2. Disengage the blades by moving the blade control switch to Off (Figure 7). Note: A warm or hot engine may not require choking. 3. Turn the ignition key to Off (Figure 9). 4.
does not operate as described below, have an Authorized Service Dealer repair the safety system immediately. 1. While sitting on the seat, with the control levers in park position, and move the blade control switch to On. Try starting the engine; the engine should not crank. 2. While sitting on the seat, move the blade control switch to Off. Move either motion control lever to the center, unlocked position. Try starting the engine; the engine should not crank. Repeat with the other motion control lever.
Forward Stopping the Machine 1. Move the levers to the center, unlocked position. To stop the machine, move the motion control levers to neutral and outward to the park position, disengage the blade control switch, ensure the throttle is in the fast position, and turn the ignition key to off. Remember to remove the key from the ignition switch. 2. To go forward, slowly push the motion control levers forward (Figure 11).
Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. 1. Raise the seat and loosen the adjustment knobs enough to move the seat (Figure 13). Important: Make sure that the spacers stay in place when loosening the knobs to move the seat. Loss of the spacers can result in damage to the seat. 2. Move the seat to the desired position and tighten the knobs. Figure 14 1. 2. Control lever Bolt 3.
Side Discharge The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death. Figure 15 1. Bypass levers 3. 2.
Cut 1/3 of the Grass Blade inside the mower, cutting quality will eventually become unsatisfactory. It is best to cut only about 1/3 of the grass blade. Cutting more than that is not recommended unless grass is sparse, or it is late fall when grass grows more slowly. Blade Maintenance Maintain a sharp blade throughout the cutting season because a sharp blade cuts cleanly without tearing or shredding the grass blades.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the rst 8 operating hours • Change the engine oil. Before each use or daily • • • • Check the safety interlock system. Check the engine oil level. Check the cutting blades. Clean the mower housing. Every 25 hours • • • • Grease all lubrication points.
Figure 17 1. Engine hood 2. Knob Figure 19 2. To install the hood, put the hooks into the slots and slide forward (Figure 18). 1. Front caster tire 3. Tighten the knobs in the engine hood (Figure 17). Figure 20 4. Connect a grease gun to each fitting (Figure 19 and Figure 20). Pump grease into the fittings until grease begins to ooze out of the bearings. 5. Wipe up any excess grease. Figure 18 1. Engine hood 2.
Cleaning the Foam Element and wait for all moving parts to stop before leaving the operating position. 1. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly. 3. Clean around the air cleaner to prevent dirt from getting into the engine and causing damage. Pull up on the air cleaner cover handle and rotate it toward the engine (Figure 21). Remove the air cleaner cover. 2. Dry the element by squeezing it in a clean cloth. Do not oil the element.
Figure 25 1. Figure 23 Oil dipstick 2. Metal end 4. Screw the oil dipstick fully onto the fill hole. Unscrew the dipstick, pull it out, and look at the end. If the oil level is low, slowly pour only enough oil into the fill hole to raise the level to, but not over, the Full mark on the dipstick. Checking the Oil Level 1. Park the machine on a level surface, disengage the blade control switch, stop the engine, and remove the key.
7. When oil has drained completely, close the drain valve. tighten the filter an additional 1/2 to 3/4 turn (Figure 27). 5. Fill the crankcase with the proper type of new oil; refer to Changing and Draining the Oil in Engine Maintenance, page 23. 8. Remove the drain hose (Figure 26). Note: Dispose of the used oil at a recycling center. 9. Change the oil filter, if necessary (Figure 27). Servicing the Spark Plug 10. Clean around the oil dipstick and unscrew the cap (Figure 24).
Important: Never clean the spark plug. Always replace the spark plug when it has a black coating, worn electrodes, an oily film, or cracks. 2. Check the gap between the center and side electrodes (Figure 29). Bend the side electrode (Figure 29) if the gap is not correct. 2. Move the motion control levers outward to the park position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
Note: Now is the best time to install a new fuel filter because the fuel tank is empty. Removing the Battery 7. Install the fuel line onto the fuel filter. Slide the hose clamp close to the fuel filter to secure the fuel line (Figure 31). Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.
the Battery in Electrical System Maintenance, page 28. Adding Water to the Battery The best time to add distilled water to the battery is just before you operate the machine. This lets the water mix thoroughly with the electrolyte solution. 1. Remove the battery from the machine; refer to Removing the Battery in Electrical System Maintenance, page 28. Important: Never fill the battery with distilled water while the battery is installed in the machine.
disconnect the charger leads from the battery posts (Figure 34). • Charge Circuit F2-25 amp, blade-type • Optional Headlight Kit-10 amp, blade type 1. Raise the seat to gain access to the fuse holder (Figure 35). 2. To replace a fuse, pull out on the fuse to remove it (Figure 35). Figure 34 1. Positive battery post 2. Negative battery post 3. 4. Red (+) charger lead Black (-) charger lead 5. Install the battery in the machine and connect the battery cables; refer to Installing the Battery.
sharpen the blades; refer to Sharpening the Blades. 2. Inspect the blades, especially the curved area (Figure 37). If you notice any damage, wear, or a slot forming in this area (item 3 in Figure 37), immediately install a new blade. Figure 36 1. Valve stem Mower Maintenance Figure 37 Servicing the Cutting Blades 1. 2. Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades.
A blade that is bent or damaged could break apart and could seriously injure or kill you or bystanders. Figure 40 1. Sharpen at original angle • Always replace bent or damaged blade with a new blade. • Never file or create sharp notches in the edges or surfaces of blade. 2. Check the balance of the blade by putting it on a blade balancer (Figure 41). If the blade stays in a horizontal position, the blade is balanced and can be used.
3. Check the air pressure of all four tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure in Drive System Maintenance, page 30. 4. Set the height-of-cut lever to position D [3 inch (76 mm)]. 5. Carefully rotate the blade(s) side to side (Figure 42). Measure between the outside cutting edges and the flat surface (Figure 42). If both measurements are not within 3/16 inch (5 mm), an adjustment is required; continue with this procedure.
refer to Checking the Tire Pressure in Drive System Maintenance, page 30. 4. Check and adjust the side-to-side blade level if you have not checked the setting; refer to Leveling the Mower from Side-to-Side. 5. Measure the length of the rod extending out of the adjusting block on the sides of the chassis (Figure 45). 6.
level of the mower; refer to Leveling the Mower from Side-to-Side. Removing the Mower Note: Before removing the mower, make a note for which holes are used in the leveling brackets (Figure 49). 1. Park the machine on a level surface and disengage the blade control switch. Figure 49 2. Move the motion control levers outward to the park position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 38 inch leveler bracket shown 1. 2.
and wait for all moving parts to stop before leaving the operating position. 3. Slide the mower under the machine. 4. Lower the height-of-cut lever to the lowest position. 5. Attach the adjusting rod to the machine with the washer and hairpin cotter (Figure 49) on each side of the mower. 6. Slide the leveling brackets onto the mounting pins and secure them with the washers and hairpin cotters (Figure 49). 7. Attach the front support rods to the machine with the clevis pins and hairpin cotters (Figure 48).
Slide rod through second grass deflector bracket and internal lock washer (Figure 51). 7. Insert rod at front of grass deflector into short stand-off on deck. Secure rear end of rod into the mower with a nut (3/8 inch) (Figure 51). Important: The grass deflector must be spring loaded in the down position. Lift the deflector up to test that it snaps to the full down position. Figure 52 1. 2. Washout tting Hose 3. 4. O-ring Coupling 4. Lower the mower to the lowest height-of-cut. 5.
Storage Stop the engine, allow it to cool, and drain the fuel tank; refer to Draining the Fuel Tank in Fuel System Maintenance, page 27. Cleaning and Storage Restart the engine and run it until it stops. 1. Disengage the blade control switch, move the motion controls outward to the park position, stop the engine, and remove the key. Choke or prime the engine. Start and run the engine until it will not start. Operate the primer, if equipped, several times to ensure no fuel remains in the primer system.
Troubleshooting Problem The engine overheats. Possible Cause 1. The engine load is excessive. 2. The oil level in the crankcase is low. 3. The cooling ns and air passages under the engine blower housing are plugged. 4. The air cleaner is dirty. 5. Dirt, water, or stale fuel is in fuel system. The starter does not crank 1. The blade control switch is engaged. 2. The motion control levers are not in the park position. 3. The operator is not seated. 4. The battery is dead. 5.
Problem Possible Cause Corrective Action The engine will not start, starts hard, or fails to keep running. 1. The fuel tank is empty. 1. Fill the fuel tank. 2. The fuel valve turned off. 2. Open the fuel valve. 3. The choke is not on. 3. Move the choke lever to On. 4. The air cleaner is dirty. 4. Clean or replace the air cleaner element. 5. The spark plug wire(s) is 5. Install the wire(s) on the loose or disconnected. spark plug. 6. Install a new, correctly 6. The spark plug(s) is gapped spark plug(s).
Problem Possible Cause Corrective Action There is abnormal vibration. 1. The engine mounting bolts are loose. 2. The engine pulley, idler pulley, or blade pulley is loose. 3. The engine pulley is damaged. 4. The cutting blade(s) is/are bent or unbalanced. 5. A blade mounting bolt is loose. 6. A blade spindle is bent. 1. Tighten the engine mounting bolts. 2. Tighten the appropriate pulley. 3. Contact an Authorized Service Dealer. 4. Install a new cutting blade(s). 5. Tighten the blade mounting bolt. 6.
Schematics Electrical Diagram (Rev.
International Distributor List—Consumer Products Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip B-Ray Corporation Casco Sales Company Ceres S.A CSSC Turf Equipment (pvt) Ltd Cyril Johnston & Co Equiver Femco S.A. G.Y.K. Company ltd. Geomechaniki of Athens Guandong Golden Star Hako Gorund and Garden Hydroturf Int. Co Hydroturf Egypt LLC Ibea S.p.A. Irriamc Jean Heybroek b.v. Lely (U.K. ) Limited Maquiver S.A. Maruyama Mfg. Co. Inc. Metra Kft Mounteld a.s. Munditol S.A.
The Toro Warranty Conditions and Products Covered Instructions for Obtaining Warranty Service The Toro® Company and its afliate, Toro Warranty Company, pursuant to an agreement between them, jointly promises to the original purchaser* to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship.