Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74432

Form No. 3357-921 Rev A

TimeCutter® ZD Riding Mower

Model No. All Models

Setup Instructions

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Charge the battery.

Retainer clip

Screw, self-tapping (10 x 1/2 inch)

Install the bag clips.

Collection bag

DFS lever

Washer

Cotter pin

Install the collection bag.

Ignition Key

Operator’s Manual

Engine Operator’s Manual

Complete the Setup.

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Step

Charging the Battery

No Parts Required

Procedure

Bulk electrolyte with 1.260 speciﬁc g ra vity m ust be

purc hased from a local batter y supply outlet.

Batter y electr ol yte contains sulfuric acid

which is a deadl y poison and causes sev er e

bur ns.

• Do not drink electr ol yte and a v oid

contact with skin, ey es or clothing . W ear

safety g lasses to shield y our ey es and

r ob ber g lo v es to pr otect y our hands.

• Fill the batter y wher e clean w ater is

al w ays a v aila ble f or ﬂushing the skin.

• F ollo w all instr uctions and compl y with

all safety messa ges on the electr ol yte

container .

1. Raise the seat to access the batter y .

2. R emo v e the batter y from the mac hine and

place it on a lev el surface; refer to the Operator’ s

Manual , R emo ving the Batter y .

Important: Nev er ﬁll the batter y with

electr ol yte while the batter y is installed in

the tractor . Electr ol yte could be spilled on

other par ts and cause cor r osion.

3. Clean the top of the batter y with a paper to w el.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (4 pages)

PAGE 1
Form No. 3357-921 Rev A TimeCutter® ZD Riding Mower Model No. All Models Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 3 4 Qty. Description No parts required – Retainer clip Screw, self-tapping (10 x 1/2 inch) Collection bag DFS lever Washer Cotter pin Ignition Key Operator’s Manual Engine Operator’s Manual 2 4 1 1 1 1 1 1 1 Use Charge the battery. Install the bag clips. Install the collection bag. Complete the Setup.
PAGE 2
4. Remove the vent caps from the battery (Figure 1). Slowly pour electrolyte into each battery cell until the electrolyte level is up to the Upper line on the battery case (Figure 1). 8. Charge the battery for 10 to 15 minutes at 25 to 30 amps or 30 minutes at 4 to 6 amps (Figure 2). Do not overcharge the battery. 9. When ﬁnished, unplug the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Figure 2).
PAGE 3
G005849 4 2 2 1 1 G005848 5 Figure 3 1. Bag clip 2. Screw 3. Heat shield, backside 4. 5. 6. 6 3 4 Holes, existing Heat shield Bag clip, installed 3. Repeat this procedure for the remaining clip on the opposing side of the heat shield. Figure 4 1. 2. Step 3 3. 4. Washer Cotter pin 3. Install a washer over the end of the DFS lever inside the collection bag (Figure 4). 4. Secure the lever assembly with a cotter pin and bend the ends to hold it place (Figure 4). 5.
PAGE 4
Step 4 Completing the Setup Parts needed for this step: 1 1 1 Ignition Key Operator’s Manual Engine Operator’s Manual Procedure Checking the Tire Pressure Check the front and rear tires for proper inﬂation. Refer to Checking the Tire Pressure in the Operator’s Manual for the recommended inﬂation pressure. Checking the Mower Adjustment The mower deck was leveled at the factory. If the mower is not cutting level, adjust the side-to-side level and the front-to-rear blade slope.