Form No. 3357-683 Rev A Z441 Z Master® with 48in or 52in TURBO FORCE® Side Discharge Mower Model No. 74441—Serial No. 270000001 and Up Model No. 74442—Serial No. 270000001 and Up Register your product at www.Toro.
Warning CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Important: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land. Other states or federal areas may have similar laws. Figure 1 1.
Using the Rollover Protection System (ROPS).................. 15 Think Safety First .............................. 16 Operating the Parking Brake .............. 17 Starting and Stopping the Engine .............................. 17 Operating the Power Take Off (PTO) ............................... 19 The Safety Interlock System............... 19 Driving Forward or Backward ............ 20 Stopping the Machine ........................ 21 Adjusting the Height-of-Cut ..............
Safety hair, loose clothing or jewelry may get tangled in moving parts. • Inspect the area where the equipment is to be used and remove all objects such as rocks, toys and wire which can be thrown by the machine. • Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive. – Use only an approved container – Never refuel or drain the machine indoors. – Never remove gas cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke.
• Never carry passengers and keep pets and bystanders away. • Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions. • Slow down and use caution when crossing roads and sidewalks. Stop blades if not mowing. • Be aware of the mower discharge direction and do not point it at anyone. • Do not operate the mower under the influence of alcohol or drugs. • Use extreme care when loading or unloading the machine into a trailer or truck.
• Carefully release pressure from components with stored energy. • Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last. • Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them. • Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running.
Slope Chart 7
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 58-6520 1. Grease 1-403005 66-1340 1-523552 65-2690 1-633818 68-8340 98-4387 54-9220 1. Warning—wear hearing protection.
8-5954 107-1687 103-2644 105-7798 107-1688 107-1613 9
Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. 2. No re, open ame, or smoking. 7. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8. 5. Read the Operator’s Manual. 9. 10. 107-2112 Keep bystanders a safe distance from the battery. Wear eye protection; explosive gases can cause blindness and other injuries Battery acid can cause blindness or severe burns. Flush eyes immediately with water and get medical help fast.
Manufacturer’s Mark 1. Indicates the blade is identied as a part from the original machine manufacturer. 107-8445 107-9309 1. Warning—read the Operator’s Manual for information on charging the battery; contains lead; do not discard. 2. Read the Operator’s Manual. 108-5995 1. Fast 2. Slow 3. Neutral 11 4.
110-0439 1. Choke 2. Engine—stop 3. 4. Engine—run Engine—start 5. Fast 6. Continuous variable setting 12 7. Slow 8.
Product Overview Using the Hour Meter The hour meter (Figure 5) records the number of hours the engine has operated. It operates when the engine is running. Use these times for scheduling regular maintenance. Figure 5 1. Hour meter Using the Fuel Shutoff Valve The machine has 2 fuel tanks, one on the left side and the other on the right side. Each tank connects to a check valve and then to a tee. From there a common fuel line leads to the engine (Figure 6). Figure 3 1. 2. 3. 4. 5.
Operation In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. Note: Determine the left and right sides of the machine from the normal operating position. Adding Fuel • Always place gasoline containers on the ground away from your vehicle before filling. Use Unleaded Regular Gasoline suitable for automotive use (85 pump octane minimum).
• Cleans the engine while it runs • Eliminates gum-like varnish buildup in the fuel system, which causes hard starting There is no rollover protection when the roll bar is in the down position. Important: Do not use fuel additives containing methanol or ethanol. • Lower the roll bar only when absolutely necessary. Add the correct amount of gas stabilizer/conditioner to the gas. • Do not wear the seat belt when the roll bar is in the down position.
Think Safety First 5. To raise the roll bar, remove the hairpin cotter pins and remove the two pins (Figure 8). 6. Raise the roll bar to the upright position and install the two pins and secure them with the hairpin cotter pins (Figure 8). Please read all safety instructions and symbols in the safety section. Knowing this information could help you or bystanders avoid injury. Important: Always use the seat belt with the roll bar in the raised position.
Setting the Parking Brake 1. Move the motion control levers (Figure 18) out to the neutral lock position. 2. Pull up and back on the parking brake lever to set the parking brake (Figure 12). The parking brake lever should stay firmly in the engaged position. Parking brake may not hold machine parked on a slope and could cause personal injury or property damage. Do not park on slopes unless wheels are chocked or blocked Figure 10 1. Safe Zone-use the Z Master 3.
Figure 15 1. Throttle—fast 2. Throttle—slow 6. Turn the ignition key to Start. When the engines starts, release the key (Figure 16). Figure 13 1. PTO—on 2. PTO—off Important: Do not engage starter for more than 10 seconds at a time. If engine fails to start allow 30 second cool-down period between attempts. Failure to follow these instructions can burn out starter motor. 4. Move the choke control to the on position before starting a cold engine (Figure 14).
Important: Make sure that the fuel shut off valve is closed before transporting or storing the machine, as fuel leakage may occur. Set the parking brake before transporting. Make sure to remove the key as the fuel pump may run and cause the battery to lose charge. Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. Figure 17 Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes.
engaged or if you rise from the seat when the PTO is engaged. Machine can spin very rapidly. Operator may lose control of machine and cause personal injury or damage to machine. Testing the Safety Interlock System Test the safety interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately. • Use caution when making turns. • Slow the machine down before making sharp turns. 1.
page 14. Remember to remove the key from the ignition switch. Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. Adjusting the Height-of-Cut The height-of-cut is adjusted from 1-1/2 to 4-1/2 inch (38 to 114 mm) in 1/4 inch (6 mm) increments by relocating the clevis pin into different hole locations. 1.
Adjusting the Anti-Scalp Rollers Whenever you change the height-of-cut, it is recommended to adjust the height of the anti-scalp rollers. 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. After adjusting the height-of-cut, adjust the rollers by removing the flange nut, bushing, spacer, and bolt (Figure 20 , Figure 21 and Figure 50 ).
Position B Use this position when bagging. Figure 24 Figure 22 1. Cam lock 3. 2. Lever 4. Rotate cam to increase or decrease locking pressure Slot Position C This is the full open position. The suggested use for this position is as follows. Positioning the Flow Bafe • Use in tall, dense grass mowing conditions. The following figures are only recommendations for use. Adjustments will vary by grass type, moisture content, and height of grass. • Use in wet conditions.
Figure 25 Figure 27 1. Seat latch 2. Fuel cap Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. 3. Seat Pushing the Machine by Hand Important: To adjust, move the lever sideways to unlock seat (Figure 26). Important: Always push the machine by hand. Never tow the machine because hydraulic damage may occur. Slide the seat to the desired position and release lever to lock in position.
necessary lighting and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets or bystanders avoid injury. To transport the machine: • Lock the brake and block the wheels. • Securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes. • Secure a trailer to the towing vehicle with safety chains. Figure 28 1. Side console controls 2. By-pass valve 3.
Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp. Both maneuvers can cause the unit to tip backward. Loading a unit onto a trailer or truck increases the possibility of backward tip-over and could cause serious injury or death. • Use extreme caution when operating a unit on a ramp. • Use only a single, full width ramp; Do Not use individual ramps for each side of the unit.
Mowing Direction tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. Alternate mowing direction to keep the grass standing straight.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the rst 8 operating hours • Change the engine oil. • Check the hydraulic uid. After the rst 25 operating hours • Change the hydraulic lter and oil. Before each use or daily • • • • • Check the safety system. Check the engine oil level. Clean the air intake screen. Check the mower blades. Clean the mower deck. Every 25 hours • • • • • Grease the mower deck and spindles.
Lubrication Greasing and Lubrication Lubricate the machine when shown on the Check Service Reference Aid decal (Figure 30). Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: General-purpose grease. How to Grease 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Figure 30 3.
4. Grease the three spindle bearings under the pulleys until grease comes out the lower seals (Figure 31). 5. Grease the idler arm on the mower deck (Figure 31). 6. Grease the fittings on the push arms (Figure 31). Figure 32 1. Latches 2. Air cleaner cover 3. 4. Air lter body Primary lter 4. Clean the inside of the air cleaner cover with compressed air. 5. Gently slide the air filter out of the air cleaner body (Figure 32). Avoid knocking the filter into the side of the body. 6.
Servicing the Engine Oil Service Interval/Specication Change the engine oil as follows: • After the first 8 operating hours • After every 100 operating hours Note: Change the oil more frequently when the operating conditions are extremely dusty or sandy. Figure 34 1. Oil Type: Detergent oil (API service SF, SG, SH, or SJ) Oil dipstick 2. Filler tube 5. Unscrew the oil dipstick and wipe the end clean (Figure 34). Crankcase Capacity: 58 ounces (1.7 liter) with the filter removed; 51 ounces (1.
Figure 36 1. Oil lter 2. Adapter 11. Slowly add the additional oil to bring it to the Full mark. 3. Apply a thin coat of new oil to the rubber gasket on the replacement filter (Figure 36). 4. Install the replacement oil filter to the filter adapter, turn the oil filter clockwise until the rubber gasket contacts the filter adapter, then tighten the filter an additional 3/4 turn (Figure 36). 5. Fill the crankcase with the proper type of new oil; refer to Servicing the Engine Oil. 6.
Important: Always replace the spark plugs when it has a black coating, worn electrodes, an oily film, or cracks. 3. Disconnect the wires from the spark plugs (Figure 37). 3. Check the gap between the center and side electrodes (Figure 38). Bend the side electrode (Figure 38) if the gap is not correct. Installing the Spark Plugs 1. Install the spark plugs and the metal washer. Ensure that the air gap is set correctly. 2. Tighten the spark plugs to 16 ft-lb (22 N•m). 3.
5. Disconnect the fuel line from the fuel filter (Figure 39). 6. Open the fuel shutoff valve. Note: Allow gasoline to drain into a fuel container can or drain pan (Figure 39). Note: Now is the best time to install a new fuel filter because the fuel tank is empty. 7. Install the fuel line onto the fuel filter. Slide the hose clamp close to the fuel filter to secure the fuel line (Figure 39). Figure 39 1. Fuel shutoff valve 2. Hose clamp 3. 4. Electrical System Maintenance Fuel line Fuel lter 6.
Removing the Battery Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • When removing or installing the battery, do not allow the battery terminals to touch any metal parts of the machine. • Do not allow metal tools to short between the battery terminals and metal parts of the machine. Figure 40 1. 2. 3. 4. 5. 6.
Charging the Battery Fuse: • Main, F1-30 amp, blade-type • Charge circuit, F2-25 amp, blade-type Charging the battery produces gasses that can explode. • Optional head light kit, 10 amp, blade-type 1. Raise the seat to gain access to the fuse holder (Figure 42). Never smoke near the battery and keep sparks and flames away from battery. 2. To replace the fuses, pull out on the fuse to remove it. Important: Always keep the battery fully charged (1.265 specific gravity).
Drive System Maintenance Checking the Tire Pressure Check the pressure at the valve stem after every 50 operating hours or monthly, whichever occurs first (Figure 44). Adjusting the Tracking Maintain the air pressure in the rear tires at 13 psi (90 kPa). Uneven tire pressure can cause an uneven cut. Check the tires when they are cold to get the most accurate pressure reading. Note: Determine the left and right sides of the machine from the normal operating position.
Figure 45 1. Slotted Nut 2. Two threads or less showing 3. 4. Figure 46 Hole in threaded shaft Washer (if needed) 1. Spring Washers 2. Lock Nut 5. Check the distance from bottom of slot in nut to inside edge of hole. Two threads or less should be showing (Figure 45). 3. Dust Cap Cooling System Maintenance 6. If more than two threads are showing remove nut and install washer between hub and nut. Cleaning the Air Intake Screen 7. Torque the slotted nut to 125 ft-lb. (170 N•m) (Figure 45). 8.
Figure 48 1. Figure 47 1. Guard 2. Air intake screen 3. 4. 2. 3. 4. Bolt Fan housing Brake lever 5. 3/16 to 1/4 inch (5 to 7 mm) Spring, 2-3/4 inch (74 mm) 6. Jam nut and yoke 7. Trunnion Adjusting nuts Collar on brake rod 3. If an adjustment is necessary, do the following: A. Loosen the jam nut below the spring and tighten the nut directly below the yoke (Figure 48). B. Turn the nut until you obtain the correct measurement. C.
Check belts for cracks, frayed edges, burn marks or any other damage. Replace damaged belts. Replacing the Mower Belt The signs of a worn mower belt are squealing while the belt is rotating, blades slipping while you are cutting grass, frayed belt edges, burn marks, and cracks. Replace the mower belt if you detect any of these signs. 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. Figure 50 2.
7. Release the pressure on the spring loaded idler (Figure 51). 8. Install the mower belt. Figure 52 1. 2. Figure 51 1. Belt 2. Clutch electrical wire 3. Clutch stop 4. 5. 6. Bolt Clutch Idler Push arm 15–1/8 inch (384 mm) 3. 4. Jam nut Ball joint 2. Adjust each side the same amount. Each push arm should have a length of 15–1/8 inch (384 mm) (Figure 52). Note: Increase the tension by lengthening the push arms; decrease the tension by shortening the push arms.
5. Move lever to the neutral position but not locked (Figure 53). Figure 53 1. Neutral locked position 2. Control lever 3. Neutral position 6. Pull the lever back until the clevis pin (on the arm below the pivot shaft) contacts the end of the slot (just beginning to put pressure on the spring) (Figure 54). Figure 54 1. 2. 3. 4. 5. Clevis pin in slot Nut Nut-Left hand thread Adjustment bolt Pump rod 6. 7. 8. 9. Double nuts Jam nut Yoke Ball joint 7.
Hydraulic System Maintenance Servicing the Hydraulic System Checking the Hydraulic Fluid Fluid Type: Mobil 1 15W-50 synthetic motor oil or equivalent synthetic oil. Figure 55 1. 2. Important: Use oil specified or equivalent. Other fluids could cause system damage. Cap Bafe 3. 4. Cold uid level-full Hot uid level-full Hydraulic System Oil Capacity: 67 ounces (2.0 l) Check the hydraulic fluid level: Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Important: Do not substitute automotive oil filter or severe hydraulic system damage may result. 3. Place a drain pan under filter, remove the old filter and wipe the filter adapter gasket surface clean (Figure 56). Figure 57 1. Hydraulic lter 2. Gasket 3.
Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Engine must be running so motion control adjustment can be performed. Contact with moving parts or hot surfaces may cause personal injury. • If hydraulic fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this type of injury. Gangrene may result if this is not done. Keep hands, feet, face, clothing and other body parts away from rotating parts, muffler and other hot surfaces.
Figure 58 1. Tracking knob 2. Pump rod 3. Adjustment bolt Setting the Right-hand Hydraulic Pump Neutral Position Figure 59 1. Double nuts 2. Pump rod 1. Loosen the locknuts at the ball joints on the pump control rod (Figure 59). 2. Start the engine, open throttle 1/2 way and release parking brake. Refer to Starting and Stopping the Engine in Operation, page 14. 3. 4. Locknut Ball joint Electrical system will not perform proper safety shut off with jumper wire installed.
Mower Deck Maintenance 6. Record this measurement. This measurement needs to be 3-1/8 to 3-1/4 inches (79 to 83mm). Leveling the Mower at Three Positions Important: There are only three measuring positions needed to level the mower. Preparing the Machine 1. Position mower on a flat surface. 2. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 3.
4. Measure the right blade at the B location, from a level surface to the cutting edge of the blade tip (Figure 62). 5. Record this measurement. 6. The mower blade should be a 1/4 to 3/8 inch (6 to 10 mm) lower at position A than at position B (Figure 62). If it is not correct, proceed to the following steps. Note: Both of the front swivels need to be adjusted the same amount to maintain equal chain tension. 7.
Before Inspecting or Servicing the Blades Park the machine on a level surface, disengage the blade control (PTO), and set the parking brake. Turn the ignition key to Off. Remove the key. Inspecting the Blades 1. Inspect the cutting edges (Figure 64). If the edges are not sharp or have nicks, remove and sharpen the blades. Refer to Sharpening the Blades. 2. Inspect the blades, especially the curved area (Figure 64).
Contact with a sharp blade can cause serious injury. Wear gloves or wrap sharp edges of the blade with a rag. 1. Hold the blade end using a rag or thickly-padded glove. 2. Remove the blade bolt, spring disk and blade from the spindle shaft (Figure 68). Sharpening the Blades Figure 65 1. Measure here from blade to hard surface 2. When sharpening blade, pieces of blade could be thrown and cause serious injury. Position A Wear proper eye protection when sharpening blade. 4.
Installing the Blades 1. Install the blade onto the spindle shaft (Figure 68). Note: Make sure the L end of the spring is installed behind the deck edge before installing the bolt as shown in Figure 69. Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. 2. Install the spring disk and blade bolt. The spring disk cone must be installed toward the bolt head (Figure 68). Torque the blade bolt to 85-110 ft-lb (115-150 N•m). 3.
Waste Disposal Engine oil, batteries, hydraulic oil, and engine coolant are pollutants to the environment. Dispose of these according to your state and local regulations.
Storage A. Add a petroleum based stabilizer/conditioner to fuel in the tank. Follow mixing instructions from the stabilizer manufacturer. Do not use an alcohol based stabilizer (ethanol or methanol). 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to Off. Remove the key. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine and hydraulic system.
Troubleshooting Problem Starter does not crank Possible Cause 1. Blade control (PTO) is engaged. 2. Parking brake is not on. 3. Operator is not seated. 4. Battery is dead. 5. Electrical connections are corroded or loose. 6. Fuse is blown. 7. Relay or switch is defective. Engine will not start, starts hard, or fails to keep running. 1. Fuel tank is empty. 2. Air cleaner is dirty. 3. Dirt in the fuel lter. 4. Dirt, water, or stale fuel is in the fuel system. Engine loses power. 1.
Problem Machine does not drive. Abnormal vibration. Possible Cause 1. By pass valve is not closed tight. 2. Drive or pump belt is worn, loose or broken. 3. Drive or pump belt is off a pulley. 4. Broken or missing idler spring. 5. Hydraulic uid level is low or too hot. 1. Tighten the by pass valve. 2. Change the belt. 1. Cutting blade(s) is/are bent or unbalanced. 2. Blade mounting bolt is loose. 3. Engine mounting bolts are loose. 4. Loose engine pulley, idler pulley, or blade pulley. 5.
Problem Blades do not rotate. Possible Cause 1. Drive belt is worn, loose or broken. 2. Drive belt is off pulley. 3. Deck belt is worn, loose or broken. 4. Deck belt is off pulley. 5. Broken or missing idler spring. 56 Corrective Action 1. Check the belt tension. 2. Install the drive belt and check adjusting shafts and belt guides for correct position. 3. Install a new deck belt. 4. Install the deck pulley and check the idler pulley, idler arm and spring for correct position and function. 5.
Schematics Wire Diagram (Rev.
Evaporative Emission Control Warranty Statement California Evaporative Emission Control Warranty Statement Your Warranty Rights and Obligations Introduction The California Air Resources Board and The Toro® Company are pleased to explain the evaporative emission control system’s warranty on your 2006 model year equipment. In California, new equipment that use small off-road engines must be designed, built, and equipped to meet the State’s stringent anti-smog standards.
LCE The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered Items and Conditions Not Covered The Toro® Company and its afliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the listed Toro Products if defective in materials or workmanship.