Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74450TE

FormNo.3365-100RevA

Z400ZMaster

With122cmTURBOFORCE

SideDischargeMower

ModelNo.74450TE—SerialNo.310000001andUp

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removepartsfromthecrate.

Nopartsrequired

–

Checkthetirepressure.

Rearwheels2Installthedrivewheels.

Rollbar,rightsection1

Rollbar,leftsection

Rollbar,centersection1

Bolt,(3/8x1inch)

Curvedwasher

Flangenut,(3/8inch)

Bolt,(1/2x3–1/4inch)

Flangenut,(1/2inch)

InstalltheRolloverProtectionSystem

(ROPS).

Lefthandarmrest

Flatwasher1

Bolt,(1/2x3-1/4inches)

Plasticatwasher

Spacer

Installtheseat.

Rightcontrollever1

Leftcontrollever

Bolt(3/8x1inch)(2areassembled)

Curvedwasher(3/8inch)(2are

assembled)

Installthemotioncontrollevers.

Nopartsrequired

–

Addingfueltothemachine.

Nopartsrequired

–

Chargethebattery.

Aircleanercap1

Hoseclamp1

Installtheaircleanercap.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3365-100 Rev A Z400 Z Master® With 122cm TURBO FORCE® Side Discharge Mower Model No. 74450TE—Serial No. 310000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 12 13 © 2010—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty. No parts required – Remove parts from the crate. No parts required – Check the tire pressure. Rear wheels 2 Install the drive wheels.
PAGE 2
Procedure 14 Description Operator’s Manual Engine Owner’s Manual Registration Card Operator training material Key 1 Qty. Use 1 1 1 1 2 Delivering the machine to the customer. 3 Removing Parts from the Crate Raising the Machine Up and Installing the Drive Wheels No Parts Required Parts needed for this procedure: Procedure 2 Remove the tires, the seat and the parts for the ROPS from the shipping crate. Rear wheels Procedure 1.
PAGE 3
. Remove the wheel nuts from both sides of the vehicle and remove the right angle retaining plate. Discard the screws and retaining plate. 4 Installing the Roll Over Protection System Parts needed for this procedure: Figure 4 4. Mount the wheels with the valve stem to the outside and secure them with the wheel nuts previously removed.
PAGE 4
2. Install the lanyard clips onto the long bolts (1/2 x 3-1/4 inch). Note: Make sure the bent tab points toward the head of the bolt. Figure 7 3. Lightly oil the ends of the center roll bar section. 4. Loosely install the center roll bar section using 2 bolts (1/2 x 3-1/4 inch) and 2 flange nuts (1/2 inch). Note: Make sure the bolts are installed from the outside of the roll bar. Note: Make sure the lanyard tab is installed as show and points forward. Figure 9 6.
PAGE 5
1 5 2 Installing the Seat Parts needed for this procedure: g012851 3 1 Lefthand armrest 1 Flat washer 1 Bolt, (1/2 x 3-1/4 inches) 1 Plastic flat washer 1 Spacer Figure 12 1. Spacer 2. Slot– install to the rear of seat 3. Bent ends 5. Install the seat and spacers to the seat frame with the previously removed nuts. Procedure 1. Install the left armrest to the seat with a flat washer, plastic flat washer, spacer and a bolt (1/2 x 3-1/4 inches). 1 2 3 4 5 6 g012850 Figure 11 1. Seat 2.
PAGE 6
Figure 14 6 Installing the Motion Control Levers Parts needed for this procedure: 1 Right control lever 1 Left control lever 4 Bolt (3/8 x 1 inch) (2 are assembled) 4 Curved washer (3/8 inch) (2 are assembled) Figure 16 Procedure Note: If the machine is not properly tracking, refer to Adjusting the Tracking in your Operator’s Manual. 1. Rotate the motion control levers to the upright position. 2. Loosely install the control levers on the outside of the posts, using 4 bolts and 4 curved washers.
PAGE 7
8 9 Charging the Battery Installing the Air Cleaner Cap No Parts Required Parts needed for this procedure: Procedure 1 Air cleaner cap 1 Hose clamp WARNING Procedure Charging the battery produces gasses that can explode and cause serious injury. 1. Remove the plastic plug. • Keep cigarettes, sparks and flames away from the battery. • Make sure the ignition switch is off. • Ventilate when charging or using the battery in an enclosed space.
PAGE 8
10 Checking the Machine for Grease Parts needed for this procedure: 1 tube Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Figure 19 Procedure 4. Install the air cleaner cap onto the air cleaner and secure it with the hose clamp. 1. Check the tensioning arm for grease. 2. Check the grease for the three spindle bearings. If needed, add grease until it comes out of the lower seals.
PAGE 9
12 Preparing the Side Discharge Chute No Parts Required Procedure Remove the plastic tie holding the side discharge chute up and lower the chute into place. Check and ensure the spring is installed correctly. The grass deflector must be able to lower down into position. Lift the deflector up to test that it lowers into the full down position. If needed, refer to Replacing the Grass Deflector in the Operator’s Manual.
PAGE 10
13 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check that all mower spindles are greased. Check the engine oil level.
PAGE 11
14 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator’s Manual 1 Engine Owner’s Manual 1 Registration Card 1 Operator training material 2 Key Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 12
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: Fuel tank caps Oil fill cap/ Oil dipstick Engine oil filter Engine oil drain Fuel filters Air filter Hydraulic fluid reservoir Hydraulic filter Battery Ignition switch Throttle lever Power take off switch (PTO) Motion control levers Parking brake Mower height-of-cut Adjustable seat Hydraulic bypass valves Rollover Protection System (ROPS) Mower deck flow baffle Refer to theOper